What Causes the Abnormal Noise When Accelerating?

2 Answers
DiKaleb
07/24/25 4:00pm
It may be caused by an improperly installed air filter or an issue with the oil-gas separator. It is recommended that the owner take the vehicle to a repair shop for inspection. The relevant details are as follows: 1. Unfiltered Air: During operation, the engine needs to draw in a large amount of air. If the air is not filtered, the dust suspended in the air can be drawn into the cylinders, accelerating the wear of the piston group and cylinders. Larger particles entering between the piston and cylinder can cause severe "cylinder scoring," which is particularly common in dry and sandy working environments. The air filter is installed in front of the carburetor or intake pipe to filter out dust and sand particles, ensuring that sufficient and clean air enters the cylinders. 2. Oil-Gas Separator: Pull out the oil dipstick slightly to check. If the noise disappears, it may be an issue with the oil-gas separator. If the noise persists, it is likely related to the clutch, and further inspection is recommended. The sound of compressed air flow produced by the turbocharger during operation is normal. The higher the engine speed or the deeper the accelerator pedal is pressed, the louder the engine noise becomes. When pressing the accelerator, do so gently and avoid pressing it all the way down suddenly, as this can cause such noises.
Was this review help?
10
5
Share
QuinnAnn
08/11/25 8:57am
A few days ago, I also encountered abnormal noises when accelerating while driving. The sound was like knocking or creaking, which was quite unsettling. There are usually many possible causes for this issue, with the most common being faults in the engine ignition system. For example, carbon buildup on the spark plugs can lead to uneven combustion, causing irregular explosions of gasoline in the cylinders, which produces abnormal noises. Another common cause is the transmission system, such as worn-out gearbox gears or a slipping clutch, which can easily produce creaking sounds under the increased load during acceleration. Additionally, leaks in the exhaust system can cause hissing sounds, especially in older cars where rubber gaskets have deteriorated. Loose belts or worn bearings are also frequent culprits, as the increased RPM during acceleration makes the noise more noticeable. When I was younger and driving in the countryside, several instances of abnormal noises turned out to be belt-related issues. If not fixed promptly, they could damage more components. For safety's sake, it's best to have it checked by a professional repair shop as soon as possible to avoid bigger problems down the line.
Was this review help?
5
3
Share
Expand All
More Forum Discussions

Why are there scratches on the car window tint film?

Scratches on the glass are definitely caused during the reapplication of the film. When removing the original car film, adhesive residue may remain on the glass. Some installers may use a knife to scrape directly on the glass, which can easily damage it. Additional information: Functions of solar films: 1. Utilize the physical properties of metals to block heat, reduce fuel consumption, and improve comfort. 2. In modern solar film production technology, aluminum, gold, copper, silver, and other metals are often vacuum-deposited or magnetron-sputtered to create multi-layered, highly insulating metal film layers. The outer shell electrons (free electrons) in metal materials are generally not bound by the nucleus. When irradiated by light waves, the electric field of the light causes the free electrons to absorb the energy of the light, producing oscillations at the same frequency as the light. These oscillations then emit light at the same frequency as the original light, known as light reflection.
8
3
Share

How many days does it usually take to get the driver's license after passing Subject 4?

Generally, you will receive the driver's license on the spot after passing Subject 4. Here is some information about obtaining the license after passing Subject 4: 1. Overview: After passing all the driving test subjects, the vehicle management office will usually process the license within one working day. In some places, you can even get the license within two hours after the test. If you choose to have the license mailed, the vehicle management office will send it to the address provided during registration. It usually takes about a week to receive the license. 2. Regulations: According to the 'Regulations on the Application and Use of Motor Vehicle Driving Licenses (2016 Edition)', Article 55 states that after passing the test, the applicant must receive no less than half an hour of safety education on civilized driving and traffic accident case warnings, and participate in the license oath ceremony. The vehicle management office shall issue the motor vehicle driving license on the same day the applicant attends the license oath ceremony. For those applying to add a permitted driving category, the original motor vehicle driving license shall be retrieved.
9
2
Share

How to Solve the Problem of Water and Fog in Taillights?

Solutions for water and fog in taillights: 1. Remove the dust cover of the taillight to allow the water vapor inside to escape quickly, although this method is relatively slow. 2. Turn on the taillight for 30 minutes to increase the internal temperature of the taillight, speeding up the evaporation of small water droplets inside. 3. Use an air gun to blow air into the taillight, promoting air circulation inside, which can accelerate defogging and dehumidification. Note that the air gun must be treated to remove moisture. Below are precautions for water in taillights: 2. After handling, reinstall the dust cover of the taillight to its original position, or wrap several layers of raw tape around the threads of the lamp cover to enhance the sealing effect. 3. When washing the car or taking it to a car wash, avoid directly spraying the taillight vents with a water gun. In fact, water ingress and fogging in car lights are influenced by various factors, but ultimately, they are determined by the structure of the car light, the temperature field inside the light, the flow field, and other factors.
16
1
Share

What is the urban fuel consumption of the Audi A6L?

Audi A6L's urban fuel consumption is 8.0L/100km. Below are the specific reasons for high car fuel consumption: 1. Affected by temperature: It leads to fluctuations in fuel consumption. In winter when the temperature is low, fuel consumption tends to increase. 2. Vehicle not serviced for a long time: Dirty engine oil and air filters can also cause increased fuel consumption. Dirty engine oil leads to poor lubrication, increasing the resistance of various moving parts in the engine, requiring more energy to overcome the resistance, thus increasing fuel consumption. 3. Insufficient tire pressure: Insufficient tire pressure increases the contact area between the tires and the ground, leading to greater friction, i.e., increased driving resistance, which raises fuel consumption. 4. Excessive carbon buildup in the vehicle: Carbon buildup can occur in the throttle body, fuel injectors, intake manifold, and piston top. Excessive carbon buildup in any of these areas can lead to incomplete combustion, thereby increasing fuel consumption.
17
5
Share

What is the real fuel consumption of the CRV 1.5T?

CRV 1.5T real fuel consumption is 6.2-6.7L/100km. Actual fuel consumption is related to driving habits, techniques, road conditions, climate, etc. Driving test data shows that the real urban fuel consumption can reach 7.5-8.5 liters/100km. Here is some information about the CRV: 1. Powertrain: It is equipped with a newly developed 2.0L double overhead camshaft i-VTEC engine from Honda, representing the latest technology from Honda. The maximum power is 110kW/6500rpm, and the maximum torque is 190N·m/4000rpm. While its power and off-road capabilities are not as strong as those of pure off-road vehicles, as a multi-purpose urban vehicle, its comfort and practicality are unmatched by off-road vehicles. 2. Design: The CRV places the handbrake on the left side of the center console, known as the column-mounted design, which not only makes operation more convenient but also provides more spacious front-row seating.
1
3
Share

Does the Outlander meet China 6 emission standards?

The Outlander does meet China 6 emission standards. Here is some information about the Outlander's China 6 models: 1. Regional distribution: Some Mitsubishi Outlander models comply with China 6 standards, while others meet China 5 standards. The China 6 models are sold in regions where China 6 standards have been implemented. 2. Exterior: The 2019 Mitsubishi Outlander features certain upgrades and optimizations to its exterior and interior based on the current model, such as the latest full LED headlights, additional chrome trim below the bumper, and new 18-inch two-tone alloy wheels. 3. Power: The 2019 Mitsubishi Outlander offers two engine options: a 2.0L and a 2.4L. The 2.0L naturally aspirated engine delivers a maximum power of 122kW (161PS) and a peak torque of 201N·m, while the 2.4L naturally aspirated engine produces a maximum power of 141kW (192PS) and a peak torque of 235N·m.
12
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.