What Causes the Abnormal Noise from Newly Replaced Tires?

2 Answers
DeHaven
07/24/25 5:05am
Reasons for abnormal noise from newly replaced tires are as follows: 1. Technicians did not perform wheel balancing: After replacing the new tires, technicians failed to perform wheel balancing, resulting in uneven resistance and wear on the tires, leading to "tire cupping." 2. The new tires are wider than the old ones: The newly replaced tires are wider than the previous ones, increasing the contact area with the ground, raising the friction coefficient, and consequently, the tire noise. The louder noise may make the driver perceive a humming abnormal sound. 3. Issues with the bearings: During the process of replacing the new tires, certain steps might not have been properly executed, causing problems with the bearings, which then produce abnormal noises.
Was this review help?
7
2
Share
OKathryn
08/11/25 12:40am
I recently got new tires too and noticed some strange noises while driving. It might be due to improper installation, like loose wheel bolts or unbalanced tires, causing shaking and noise at higher speeds. Another possibility is incorrect tire pressure—either too high or too low can cause unusual wear and noise. Or maybe there are small stones or metal debris stuck around the tires, making a squeaking sound when rubbing. I suggest checking the tire pressure first—use a cheap gauge to see if it’s within the recommended range, then brush out any debris stuck in the tire treads. If the noise persists, take it to a shop immediately—don’t wait until it damages the suspension system. My neighbor once had to pay over a thousand bucks for repairs due to a small issue. Remember, regular tire maintenance is crucial, especially in the first few weeks after getting new ones.
Was this review help?
3
5
Share
Expand All
More Forum Discussions

Does Zippo use cotton pads or rubber pads?

Zippo uses cotton pads. Zippo uses degreased cotton inside: Tear the cotton apart and remove visible impurities such as small stones and dead leaves. Wash the cotton with water until the outflow is clear. Place the cotton in an enamel pot, add water until it is just submerged, then add NaOH equivalent to 2% to 5% of the water weight. Cover and boil, then simmer for 10 minutes. Cool, rinse with plenty of water, scrubbing for about 10 minutes. Dry the washed cotton on clean paper. The function of Zippo cotton pads: Zippo cotton pads prevent oil leakage, but if too much oil is added beyond the cotton's absorption capacity, it will still seep out! Additionally, the English text on the cotton pad roughly indicates the oil filling area, and the small holes on the pad can also hold spare flints. First, choose genuine Zippo lighter fluid and keep away from fire sources. Before refueling, place waste newspaper or similar padding under the lighter to prevent oil from dripping onto the table. The appropriate amount of oil to add doesn't have an exact standard. Based on experience, add oil until the cotton appears moist, which is about 70% of the cotton's oil absorption capacity. If the lighter, which usually works well, starts having ignition issues, the first thing to consider is whether it needs refueling. However, sometimes to extend the time between refueling, people add more oil, which only leads to waste. When refueling, due to gravity, the oil settles at the top of the lighter (when the lighter is inverted, i.e., the windproof cap area). If the cotton appears moist with oil, it means too much has been added. Cotton has a saturation point for oil absorption. If the body is reassembled into the case, excess oil will leak from the bottom. Therefore, it's recommended to refuel frequently but in small amounts. After refueling, check the case and padding for any oil leakage and wipe it dry before testing the lighter.
20
0
Share

How to Turn on the Air Conditioning in the Buick Envision?

To turn on the air conditioning in the Buick Envision, simply press the AC button on the center console. Taking the 2021 Buick Envision 1.5T as an example, it belongs to the midsize SUV category with body dimensions of 4694mm in length, 1839mm in width, and 1686mm in height, featuring a wheelbase of 2750mm. It has a fuel tank capacity of 66 liters and a curb weight of 1610kg. The 2021 Buick Envision 1.5T is equipped with a MacPherson strut front suspension and a multi-link rear suspension. It is powered by a 1.5L turbocharged engine delivering a maximum horsepower of 169PS, a peak power of 124kW, and a maximum torque of 250Nm, paired with a 7-speed dual-clutch transmission.
1
3
Share

What to Do If You Fill Your Car with the Wrong Fuel?

The solutions for filling your car with the wrong fuel are: 1. If you fill high-octane fuel with low-octane fuel, short-term use will not damage the engine; 2. If you fill gasoline with diesel, the owner should contact a repair shop as soon as possible to clean the fuel tank and fuel system, conduct a comprehensive inspection of the engine, and avoid ignition to prevent damage to the car; 3. If you fill diesel with gasoline, replace the fuel immediately. Precautions for refueling your car include: 1. Refuel in the morning or evening to avoid direct sunlight at noon; 2. Add more fresh fuel before long-distance trips; 3. Do not exceed the fuel tank's upper limit; 4. Avoid using electronic devices; 5. No smoking; 6. Park, turn off the engine, and shut off the power.
3
4
Share

How to Identify the Production Date of Automotive Glass?

To identify the production date of automotive glass, follow these steps: 1. Check the code located at the bottom left or right corner of the window glass; 2. The number represents the year, while the dots represent the month; 3. If the dots are in front of the number, it indicates the first half of the year. Subtract the number of dots from 7 to get the month in the first half; 4. If the dots are behind the number, it indicates the second half of the year. Subtract the number of dots from 13 to get the month in the second half. Types and functions of automotive glass: 1. Laminated glass: A transparent adhesive plastic film is placed between two or three layers of glass, enhancing the glass's resistance to breakage; 2. Tempered glass: Ordinary glass is quenched to create internal stress. When impacted and broken, the glass shatters into small, blunt-edged pieces, reducing the risk of injury to passengers.
9
5
Share

What are the body length and width of the Baojun 310?

The body length and width of the Baojun 310 are 4032mm and 1680mm respectively. The Baojun 310 comes in the following colors: Candy White, Azure Blue, Metallic Red, Morning Glow Red, Vibrant Orange, Crystal Red, and Aurora Silver. The Baojun 310 is a compact 5-door, 5-seat hatchback with a body height of 1450mm and a wheelbase of 2550mm. It is equipped with a 1.2L naturally aspirated engine and a 5-speed manual transmission, delivering a maximum power of 59 kW and a maximum torque of 112 Nm. The drive system is front-wheel drive, with a MacPherson strut independent suspension at the front and a torsion beam non-independent suspension at the rear.
17
2
Share

Where is the license plate with 'Qiong' from?

Qiong is the license plate code for Hainan Province. The license plate codes for different regions in Hainan Province are as follows: Qiong A represents Haikou, Qiong B represents Sanya, Qiong C represents Qionghai, Qiong D represents Wuzhishan, Qiong E represents Yangpu Economic Development Zone, and Qiong F represents Danzhou City. License plates, also known as vehicle registration plates, are standardized hard number plates issued by vehicle management authorities after reviewing, inspecting, and registering vehicles applying for plates, in accordance with national vehicle management regulations. The main functions of license plates are: 1. Identifying the region to which the vehicle belongs; 2. Tracing the owner and registration information of the vehicle based on the license plate.
15
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.