What Causes Sudden Loss of Power in a Car

2 Answers
DiFinley
07/29/25 3:56am
Reasons for sudden loss of power in a car are as follows: 1. Excessive carbon deposits: When there is too much carbon buildup inside the engine, the car's ignition system may malfunction, and the engine's air intake efficiency decreases, ultimately leading to reduced engine power. The car may exhibit symptoms like weak idling, and in severe cases, it may even shake. 2. Low-quality gasoline: Fuel system failures can occur if the car is filled with low-quality gasoline, resulting in decreased engine power. If the car's fuel requirement is 95 octane, then it must be filled with 95 octane gasoline, as this is the minimum fuel standard for the car. Another possible cause is a blocked fuel tank vent, which restricts fuel supply, leading to an overly lean air-fuel mixture in the engine and reduced engine efficiency. 3. Insufficient oil: Low engine oil levels or insufficient engine coolant can increase the engine's load, impairing its cooling performance. This not only reduces engine power but also increases the car's fuel consumption.
Was this review help?
11
3
Share
VanRosalie
08/12/25 7:43am
There are quite a few reasons why a car might suddenly lose power. Last time I went on a road trip, my car couldn't accelerate even when I floored the gas pedal on a hill, which really scared me. The mechanic later said it could be due to a clogged fuel filter or a faulty fuel pump, causing insufficient fuel supply. Also, if the spark plugs fail to ignite properly, the engine won't perform well, which is often related to aging parts in older cars. Additionally, if the air filter is extremely dirty, the engine won't get enough air, affecting its power. Remember to change the oil and check the filters regularly—these small maintenance tasks can prevent a lot of trouble. If you experience a loss of power, don't rush to drive long distances; instead, find a safe place to pull over and check the issue. Otherwise, breaking down midway could be even more dangerous.
Was this review help?
5
0
Share
Expand All
More Forum Discussions

What is the matching method for replacing the idle speed motor?

There are several main methods for matching after replacing the idle speed motor: 1. Power-off method - After installing the new idle speed motor, disconnect the negative terminal of the car battery for more than 5 minutes, then restart the vehicle to check if the current idle speed is normal. 2. Turn the ignition switch on for 10 seconds, then turn it off for more than 15 seconds. Repeat this several times before starting the vehicle, as the idle speed motor can generally perform self-learning. 3. The best method is to use specialized diagnostic equipment to match the idle speed motor, followed by a test drive after completion.
6
5
Share

Can a Temporary License Plate Be Used in Other Regions?

New cars with temporary license plates can travel to other regions, but the ability to do so depends on the color of the plate. Below are the specific details: 1. Sky-blue temporary license plates: These plates are for temporary use within the administrative jurisdiction and are limited to vehicles driving within the city, so they cannot be used in other regions; 2. Brown-yellow temporary license plates: These can be used for vehicles traveling across regions, and this type of plate must be applied for if crossing city boundaries; 3. Additionally, if an expired temporary license plate is used, the vehicle may be impounded, fined, and penalized with 3 demerit points if discovered by traffic police.
6
4
Share

What are the methods for jump-starting a car with a dead battery?

Here are the specific methods for jump-starting a car with a dead battery: 1. Jump-starting with the help of another vehicle. Below are the detailed steps for jump-starting with another vehicle: (1) When jump-starting a car, you need to use jumper cables, which come in red and black. The red cable is the positive cable, and the black cable is the negative cable. First, take out the red positive jumper cable and connect one end to the positive terminal of the vehicle's battery and the other end to the positive terminal of the other vehicle's battery. (2) Then, take out the black negative jumper cable and connect one end to the negative terminal of the vehicle's battery and the other end to the negative terminal of the other vehicle's battery. (3) During the connection process, avoid letting the cables touch any metal parts of the car body to prevent a short circuit. 2. Jump-starting with an external power source. Once the positive and negative cables are properly connected, you can start the vehicle. After the car successfully starts, remove the jumper cables carefully, ensuring they do not touch any metal parts of the body or other components. Then, let the engine idle or drive for more than half an hour to allow the engine to recharge the car's battery.
7
2
Share

Is it better to service your car at a 4S shop or an external repair shop?

If you want to save money, go to an external repair shop and choose a relatively good service garage. If you want repair guarantees and don’t mind spending, go to a 4S shop. Benefits of servicing at a 4S shop: 1. Genuine parts with warranties, ensuring peace of mind while driving. 2. Professional staff, standardized operations, high first-time repair rate, and targeted repairs. 3. Guaranteed quality, excellent service, monitored by manufacturers, and under public and media scrutiny. They have the capability to provide repair guarantees. 4. Frequent visits make you a loyal customer, eligible for many promotional activities. The 4S shop will be willing and proactive in offering warranties for your car. Some repairs beyond the warranty scope may also be covered upon request.
1
2
Share

Why is there no sound from the dash cam?

There may be no sound from the dash cam because the recording switch is turned off, the microphone is damaged, or the speaker is damaged. Below is a related introduction to dash cams: A dash cam is an instrument that records images, sounds, and other relevant information during vehicle travel. After installing a dash cam, it can record the entire driving process of the car, including video images and sounds, providing evidence for traffic accidents. Different dash cam products have different appearances, but their basic components include: 1. Main unit: includes devices such as a microprocessor, data storage, real-time clock, display, lens module, operation keys, printer, and data communication interface. If the display and printer are not integrated into the main unit, there should be corresponding data display and print output interfaces. 2. Speed sensor. 3. Data analysis software. 4. Infrared camera, an essential component for night vision functionality. There are many dash cams on the market today, and differentiated products have evolved with market demands. The main configurations are no longer just basic recording functions. Many dash cams now come with navigation, some have radar detectors, some feature front and rear recording, and some include all these functions. Currently, the highest-end dash cam on the market is the smart cloud rearview mirror dash cam.
15
2
Share

Can I pass the annual inspection after changing the rims?

Changing the rims will result in failing the annual inspection. Here are the specific details about changing rims: 1. If the modification of the rims has not been approved by the traffic management department in advance, the vehicle will not pass the annual inspection normally, and the original rims must be reinstalled before the inspection. 2. According to the relevant provisions of the current "Motor Vehicle Registration Regulations," any changes to the body color, model, performance, purpose, or structure of a licensed motor vehicle, including replacing the frame, body, or engine, require the owner to apply for a modification registration with the vehicle management office. Installing spoilers, body kits, or modifying exhaust pipes are, in principle, not allowed.
7
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.