What Causes Steering Wheel Vibration During High-Speed Braking?

How to Remove the Crankshaft Pulley on a Mondeo?

Here are the steps to remove the crankshaft pulley on a Ford Mondeo: 1. First, use a Phillips screwdriver and special tools to remove the air filter; use a Phillips screwdriver to remove the front grille; 2. Loosen the bolts on the alternator bracket with tools and release the alternator, then remove the alternator belt; 3. Loosen the bolts on the A/C compressor bracket with tools and remove the compressor belt; 4. Use a flathead screwdriver to lock the flywheel in the small hole at the bottom of the transmission; simultaneously use tools to loosen the crankshaft pulley bolt and remove it. 5. At this point, the pulley should come off easily.

14

3

Share

The Simplest Method to Find 30 Centimeters

The simplest method is to divide the front of the car into three equal parts. When the right one-third of the front aligns with the sideline, the distance between the car body and the sideline is exactly 30cm. During the operation, continuously observe from the rearview mirror. When the reference point coincides with the sideline, immediately press the clutch and brake to stop. The skills for pulling over are as follows: 1. Turn on the light: When hearing the voice prompt "Please pull over ahead," first turn on the right turn signal. 2. Position: Pay attention to observe the right front and find a suitable parking spot. 3. Slow down: It is recommended to slow down to below 10km/h, shift to first gear, and the slower the speed, the more beneficial it is for the next operation.

4

5

Share

Differences Between Ferrari 488 and 458?

Ferrari 488 and 458 differ in the following aspects: 1. The Ferrari 488 is equipped with a 3.9T turbocharged V8 engine, delivering a maximum output of 669 horsepower and a peak torque of 760 Nm; the Ferrari 458 features a 4.5L naturally aspirated V8 engine, producing a maximum output of 570 horsepower and a peak torque of 540 Nm. 2. The Ferrari 488 accelerates from 0 to 100 km/h in 3 seconds; the Ferrari 458 achieves the same in 3.4 seconds. 3. The Ferrari 488 measures 4568/1952/1213 mm in length, width, and height; the Ferrari 458 measures 4527/1937/1213 mm.

7

0

Share

Should Brake Rotors Be Resurfaced or Replaced?

Severely worn brake rotors require replacement with new ones. Below are detailed instructions for brake rotor replacement: 1. Replace brake rotors after two brake pad changes: Replacing brake rotors doesn't necessarily mean replacing brake pads simultaneously. If the brake pads still have sufficient thickness, they can be retained. Generally, brake rotors should be replaced after two brake pad changes. When the combined groove depth on both sides of the rotor exceeds 3mm or the rotor edges become sharp, immediate replacement is necessary. 2. Depends on driving conditions and habits: Brake rotor replacement intervals are significantly influenced by driving environment and habits. Frequent braking in urban or mountainous areas accelerates wear, shortening replacement cycles. Conversely, highway driving with less frequent braking naturally extends service life.

5

4

Share

How to use the parking function in Tiguan L?

Tiguan L's automatic parking usage method is as follows: 1. Near the parking space, activate the automatic parking function. 2. Control the vehicle to move forward at a speed below 30km/h, keeping parallel to the roadside vehicles. 3. When a suitable parking position is detected, the onboard computer will prompt the driver to shift into R gear. 4. After shifting into R gear, the automatic parking assist system will control the vehicle to complete parking into the space. More information about Tiguan L: 1. Tiguan L is equipped with a 2.0T engine, with a maximum power of 137 kW and a peak torque of 320 Nm. 2. The 2019 Tiguan L series comes standard with keyless entry, one-button start, electronic parking brake, and other equipment.

3

4

Share

What is the speed rating of car tires?

Tire speed rating indicates the maximum speed at which a tire can carry a specified load under defined conditions. The representation method and specific classification of tire speed ratings are as follows: Tire speed rating representation method: It is represented by English letters, with different letters corresponding to different speed ratings. For example: a speed rating of W on a tire represents 270KM/h, V represents 240KM/h, H represents 210KM/h, and Y represents 300KM/h. Specific classification of tire speed ratings: Different speed ratings also mean differences in price. For tires of the same size and specification, those marked with W are certainly more expensive than those marked with V, because they have a higher load capacity than V-rated tires.

8

5

Share

What Causes Steering Wheel Vibration During High-Speed Braking?

How to Remove the Crankshaft Pulley on a Mondeo?

The Simplest Method to Find 30 Centimeters

Differences Between Ferrari 488 and 458?

Should Brake Rotors Be Resurfaced or Replaced?

How to use the parking function in Tiguan L?

What is the speed rating of car tires?

What transmission does the 15th-gen Lingpai have?

What do the letters F, D, and A on green license plates represent?

How Many Paint Surfaces Does a Bumper Count As?

How to Calculate Diesel Engine Fuel Consumption?