What Causes Loud Motorcycle Noise?

1 Answers
SanKaylee
07/30/25 7:18am
There are many factors that affect motorcycle noise, which can be summarized into the following categories: temperature, speed, load, and lubrication. Temperature: Some engine noises appear as the temperature rises, while others diminish with increasing temperature. The occurrence of certain noises is often accompanied by heating phenomena. Therefore, in addition to listening to the noise, it is also necessary to measure the temperature to aid in diagnosis. Speed: Noise has a certain relationship with engine speed and vehicle speed. Load: Load has a certain impact on noise. Generally, noise increases with the increase in load, which is a common pattern. Lubrication: Regardless of the type of noise, when lubrication conditions are poor, the noise is usually more severe.
Was this review help?
1
3
Share
More Forum Discussions

What are the differences between Porsche 911 and 718?

Here are the differences between Porsche 911 and 718: 1. Appearance: The Porsche 911 does not have an air intake on the rear door; the Porsche 718 has an air intake on the rear door. This is because the 718 is mid-engined and requires cooling, while the 911 is rear-engined and does not need side vents for cooling. 2. Engine layout: The 911 has a rear-engine, rear-wheel-drive layout; the 718 has a mid-engine, rear-wheel-drive layout. 3. Engine: The 911 is equipped with 3.0T, 3.8T, and 4.0L engines; the 718 is equipped with 2.0T and 2.5T engines.
14
4
Share

Where is the jump-start location for the Audi A4L?

The battery of the Audi A4L can be jump-started at the positive and negative terminals. Here is some related information about the Audi A4L: 1. Audi battery positive and negative terminals: Both the positive and negative terminals of the battery are located in the engine compartment. The positive terminal is next to the air filter in the engine compartment and has a cover on it. The negative terminal is located behind the positive terminal and is a metal post without any cover on its surface. 2. Overview of the Audi A4L: The Audi A4L is a model officially released by Audi on November 16, 2008. The new Audi A4L features a completely new exterior and chassis design, with the front and rear of the car resembling the Audi A5.
10
5
Share

Should You Buy a Car from a Dealership or a 4S Store?

It is recommended to purchase a car from a 4S store. Here are the advantages of buying from a 4S store: 1. Brand advantage: Most 4S stores deal with car brands that have strong brand recognition, high competitiveness, and significant market share, making brand advantage their primary competitive edge, which other car sales models cannot match. 2. Complete and standardized service system: The core competitiveness of a 4S store lies in winning customers through high-quality service. At a 4S store, consumers can access all value-added services, including car information, market trends, after-sales service, maintenance guidelines, and spare parts supply. Both complete vehicles and parts are guaranteed to be original, ensuring consumers have no concerns about after-sales service, repairs, or maintenance.
17
3
Share

What are the reasons for no air coming out after running the car air conditioner for an hour?

The reasons for no air coming out after running the car air conditioner for an hour include poor heat dissipation of the air conditioner, slow rotation speed of the external fan or a dirty air conditioner; compressor damage; damage to the compressor's overheating protector; damage to the temperature sensor; and insufficient refrigerant, leading to poor cooling effect. Poor heat dissipation of the air conditioner: The main control switch may have poor contact, or the tightening screw between the motor and the fan blade of the blower may have loosened, causing the car heater blower to stop working. Use a multimeter to measure the contact resistance of the main control switch. If the resistance is too high or zero, it indicates a fault that should be repaired or replaced immediately. If the air conditioner blower stops working, it will cause subsequent heat dissipation issues, leading the air conditioning system to engage in high-pressure protection, which results in the protective shutdown of the air conditioning compressor. Severe internal wear of the compressor: This can prevent it from functioning normally. Since the compressor plays a crucial role in the air conditioning system—primarily compressing and delivering cold air—it operates in a high-speed rotation state for extended periods, which is one of the reasons it may fail to work properly. The compressor is mainly used to compress and deliver cold air. If there is a problem, check for any refrigerant leaks. Without cold air to compress or deliver, it naturally won't work.
7
3
Share

How to Remove Glue After Peeling Off Car Film?

Methods to remove residual glue from car film: Use organic solvents or industrial alcohol; Use a hair dryer to soften the glue on the glass; Use cotton or cloth dipped in vinegar; Wipe gently with a cloth soaked in ethyl acetate. Methods to remove old car film from car glass: 1. Peel it off directly: Low-quality film is easier to handle, as its adhesive strength is not particularly strong, making removal relatively simple. High-quality car film is more difficult to remove and may require professional help or specialized tools. 2. Use vinegar: Apply vinegar evenly to the adhesive with a cotton swab. Through the glass, you can immediately see the vinegar slowly spreading between the glass and the adhesive. Then, scrape back and forth with the cotton swab, and soon the adhesive will start to peel off. There will be minimal residue left on the glass, which can be wiped clean with a paper towel, leaving the surface as good as new. 3. Use essential balm: Initially, there is no obvious reaction when essential balm comes into contact with the adhesive. Persistently apply the balm to the adhesive and then scrape with a cotton swab. Gradually, the adhesive will soften, and some parts will start to peel off. With continuous application and scraping, the reaction speeds up, and within about 2 minutes, the adhesive will be completely removed. 4. Use alcohol: Apply alcohol to the adhesive on the glass, and you will immediately see the adhesive slowly soften and dissolve. Gently peel it off by hand, and the adhesive will come off cleanly from the glass.
9
5
Share

What is the Active Braking Active Safety System?

Here is a detailed introduction to automotive safety systems: 1. Types: There are two categories—active safety systems and passive safety systems. 2. Active Safety Systems: Include electronic devices such as ABS and ESP. 3. Passive Safety Systems: Involve vehicle body energy-absorbing structures, seat belts, airbags, etc. Below is additional information on safety systems: 1. Assisted Deceleration: When the vehicle ahead brakes, stops, or encounters other obstacles, the active safety system automatically applies additional force to the braking system, helping the driver reduce braking distance. It can also adjust the steering wheel to alter the vehicle's path and avoid obstacles. 2. Risk Reduction: The active braking technology system can achieve active deceleration and also reduce losses and risks in emergency situations, which reflects the maturity of automotive safety.
13
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.