···
Log in / Register

What Causes Increased Tire Noise?

4 Answers
DelCarson
09/06/25 7:41am

Tire noise increase is related to four factors: 1. Tire material: Undoubtedly, tires with softer materials generally have better noise control during driving, but they may lack in wear resistance. 2. Tread pattern design: As tires rotate rapidly during movement, air quickly impacts the tread patterns, and the noise generated from this impact constitutes the main source of tire noise. It can be observed that tires focusing on quiet performance typically feature densely arranged, fine tread patterns. 3. Groove cavity compression: Since tires are made of elastic rubber, when they contact the ground, the compression deformation compresses and expels air from the groove cavities in contact with the ground, generating noise as the air is forcibly expelled. 4. Poor vehicle sound insulation: Inadequate use of noise-reducing foam in the wheel arches is also one of the factors contributing to loud tire noise.

Was this review help?
16
4
Share
SanEmilio
09/18/25 7:18am

I noticed increased tire noise while driving, which is quite annoying. I need to check the possible causes. The most common issue is tire-related, such as aging or severe wear. When the tread becomes shallow, it tends to produce a humming sound on the road. Additionally, incorrect tire pressure—either too high or too low—can also cause this, so maintaining proper inflation is essential for stability. Another possibility is unbalanced wheels or loose suspension, which can amplify noise over bumps. Road conditions play a role too; newly paved roads are quieter, while older, uneven surfaces tend to be noisier. If the noise becomes more noticeable at higher speeds, it might be due to the tire type—for example, performance tires are initially quieter but become louder as they wear. I recommend regularly inspecting tire condition and replacing them if the edges are worn, as this affects driving safety. Periodic visits to the repair shop for adjustments can prevent prolonged noise exposure, which not only strains your ears but also increases fuel consumption. Overall, maintaining good habits can minimize such annoyances.

Was this review help?
12
0
Share
Expand All
SavannahLynn
11/01/25 7:45am

Recently, the tire noise has become noticeably louder when driving on the highway, so I really need to pay attention. I think it's mainly related to tire wear. After several years of use, the tires have worn flat, causing uneven contact with the ground, which leads to noise. Tire pressure is also crucial—both overinflation and underinflation are problematic. It's important to inflate them according to the manual, such as slightly reducing pressure during hot summers. If suspension components are worn, like a damaged shock absorber, increased tire vibration can amplify the noise. Additionally, unbalanced wheels or improper tire installation, such as mounting the tread pattern in the wrong direction, can also contribute. Frequent driving on gravel roads can add to the issue due to the rough surface. Ignoring these problems might lead to more serious issues like a tire blowout, so if something feels off, it's best to stop and check or visit a professional shop. Regular maintenance, including checking tire pressure and wear, can prevent a lot of trouble.

Was this review help?
11
3
Share
Expand All
VanNaomi
12/15/25 7:53am

When the tire noise increases, I think the reasons are quite straightforward. The main cause is tire wear; shallow tread patterns make more noise on highways. Incorrect tire pressure can also lead to noise when driving on hard surfaces. Additionally, a damaged suspension can increase vibrations. These are the basic issues, and it's best to address them promptly.

Was this review help?
11
1
Share
Expand All
More Forum Discussions

What is the most reasonable RPM for a manual transmission?

Manual transmission vehicles typically maintain an engine RPM between 1500 and 2000. Below are the relevant details:1. Generally, shifting gears at around 3000 RPM is sufficient. The higher the engine RPM, the more work is done per unit time, thus increasing power. However, higher RPMs speed up the entire cycle, causing fuel to be expelled before it has enough time to fully combust.2. Therefore, higher RPMs are not always better. The optimal RPM mainly depends on the speed and gear, and maintaining around 3000 RPM is advisable.3. Additionally, avoid low-gear high-speed and high-gear low-speed driving, as these can cause significant damage to the engine.
17
3
Share

Is a battery voltage of 10.5V considered faulty?

A battery voltage of 10.5V cannot definitively determine if it is damaged. Use a tester to check its health status; if it is below 45%, it generally should be replaced. Here are specific details about car batteries: 1. Function of a car battery: When starting the engine, it provides a strong starting current to the starter and works together with the generator to supply power to electrical devices. When the engine is idling, it supplies power to electrical devices. The car battery also acts as a capacitor, protecting the vehicle's electrical equipment. 2. Voltage: With the increasing number of electrical devices in vehicles and the emergence of mild hybrids, the 12V voltage is no longer sufficient, leading to a continuous increase in voltage. Currently, the mainstream mild hybrid voltage is 48V.
18
3
Share

What are the symptoms of a faulty temperature sensor in an EFI vehicle?

When the temperature sensor in an EFI vehicle fails, it can cause overheating or cylinder scuffing. Here is some relevant information about temperature sensors: 1. Working principle: After environmental temperature changes, the temperature sensor will produce a corresponding extension, so the sensor can convert this reaction into signals in different ways. A bimetallic strip consists of two metals with different expansion coefficients bonded together. As the temperature changes, material A expands more than the other metal, causing the strip to bend. The curvature of the bend can be converted into an output signal. 2. Categories: To achieve reliable temperature measurement, it is essential to first select the correct temperature instrument, i.e., the temperature sensor. Thermocouples, thermistors, platinum resistance (RTD), and temperature ICs are the most commonly used temperature sensors in testing.
14
5
Share

What does Battery 2.0 mean?

Battery 2.0 indicates that the battery capacity is 20AH. Here are some precautions for automotive battery usage: 1. Parking at night: Shift the gear to neutral or N position, and observe whether the car lights dim. When the vehicle is in neutral, the engine idles, and the lights are entirely powered by the battery. Insufficient battery charge will cause the lights to dim. 2. Battery replacement: It is recommended that owners replace the battery with a quality-assured one to avoid purchasing inferior products. Regular cleaning of dust and oxides on the battery surface is necessary during use. 3. Develop good driving habits: Turn off the headlights, air conditioning, and other electrical devices before parking. Wait a few minutes after starting the vehicle before using the air conditioning or other electrical appliances to reduce the instantaneous load on the car battery and extend its service life.
15
3
Share

Where is the Tire Pressure Module of the Baojun 510 Located?

The tire pressure module of the Baojun 510 is located at the vehicle's onboard computer. Below is a relevant introduction to the Baojun 510: 1. Exterior Design: The Baojun 510 features a distinctive split-headlight design, with LED daytime running lights connected to the large front grille, while the main headlights are positioned on either side of the grille. The rear of the vehicle uses conventional halogen tail lights. 2. Configuration: The Baojun 510 is equipped with an 8-inch LCD capacitive touchscreen, along with practical features such as keyless entry + one-button start, automatic climate control, leather-wrapped steering wheel, cruise control, and power-adjustable/folding/heated exterior mirrors.
16
2
Share

Should you use low beam or high beam when driving on the highway at night?

You should use high beam when driving on the highway at night. Because highway driving is fast and requires good visibility distance, high beam is the correct method to ensure visibility in relatively empty roads with no lighting at night. Here are the detailed explanations: 1. The use of headlights on highways depends on specific driving habits. 2. You can use high beam when driving in areas without street lights to expand the field of vision. 3. However, when encountering oncoming vehicles, you should switch to low beam for safety and courtesy. 4. When driving at low speeds, the engine's power generation is insufficient, and the battery is in a state of negative charge. Using high beam will affect its service life. In addition, using high beam when driving at low speeds at night will also increase the vehicle's fuel consumption.
7
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.