What Causes High Water Temperature in Wuling Rongguang Mini Truck?

1 Answers
LaElaina
07/29/25 3:35pm
Wuling Rongguang Mini Truck's high water temperature may be caused by not replacing the coolant for a long time. The Wuling Rongguang Mini Truck uses a water-cooled engine, which relies on the continuous circulation of coolant within the engine for heat dissipation. The antifreeze has two circulation paths in the engine: one is the large circulation, and the other is the small circulation. The related introduction is as follows: 1. Small Circulation: When the engine has just started, the antifreeze performs a small circulation. At this time, the antifreeze does not pass through the radiator for heat dissipation, which helps the engine to warm up quickly. 2. Large Circulation: When the engine reaches the normal operating temperature, the antifreeze will perform a large circulation. At this time, the antifreeze will pass through the radiator for heat dissipation, which can keep the engine within a reasonable temperature range.
Was this review help?
7
3
Share
More Forum Discussions

What is the method for cleaning a car throttle body?

Method for cleaning a car throttle body: 1. Remove the intake bellows at the front end of the throttle body; 2. Turn on the car ignition switch without starting the engine, press the accelerator pedal to operate the throttle cable, placing the throttle body in the fully open position; 3. After matching the throttle body, restart the engine and let it idle for 3 to 5 minutes, then perform rapid acceleration 2 to 3 times, keeping the maximum speed at 3000 RPM per second. The throttle body is used to control the intake air volume. The accelerator pedal actually controls the opening degree of the throttle body, and the control unit adjusts the fuel injection amount based on the throttle opening and opening rate. When the throttle body becomes dirty, its efficiency decreases, and the opening angle increases. The control unit will make certain adjustments and matches. Under normal conditions, the adaptive adjustment value for idle speed is 1.
16
0
Share

How to Solve High Fuel Consumption in Suzuki Swift?

Insufficient tire pressure and tire wear. Insufficient or low tire pressure will increase friction between the tires and the ground, leading to greater resistance and higher fuel consumption. Regularly clean carbon deposits. Poor-quality gasoline can cause excessive carbon buildup, which roughens the intake pipe walls and increases fuel consumption.
3
1
Share

How to Activate One-Touch Window Control in Lincoln Vehicles?

Locate the window control button, press and hold it until the window is fully raised. After the window is completely closed, continue holding the button for approximately 2 to 5 seconds. At this point, you can release the button to enable one-touch window control. One-touch window control refers to a system where the car window glass can be fully raised or lowered with a single press of a button. Its main functions are to facilitate operation for drivers and passengers and to enhance safety.
5
1
Share

What to Do When the Brakes Fail in an Automatic Transmission Car?

Automatic transmission cars have fewer pedals than manual transmission cars, lacking a clutch pedal, and only have an accelerator pedal and a brake pedal. The brake pedal is on the left, and the accelerator pedal is on the right. The operation method involves pivoting the right heel to rotate left and right, using the sole of the foot to press the brake or accelerator pedal. Automatic transmission refers to the car's automatic gear shifting mechanism, from top to bottom, respectively: Parking or starting gear P, reverse gear R, neutral gear N, forward gear also known as drive gear D, sports mode S, and low gear L.
19
4
Share

How to Use the Auto Hold Function?

The usage method of the auto hold function is: 1. After enabling the auto hold function, there is no need to pull the handbrake when waiting at traffic lights; 2. After coming to a complete stop, there is no need to switch back and forth between D gear and N gear, or D gear and P gear; 3. In D gear or N gear, there is no need to keep the foot on the brake pedal, as the vehicle will remain stationary; 4. When the vehicle starts moving again, the system determines that the vehicle is about to start based on the throttle action and engine traction, and the braking force is automatically released. The gears of an automatic transmission are: 1. P is the parking gear. After the vehicle stops, engaging P gear will prevent the vehicle from moving; 2. R is the reverse gear, which can only be engaged when the vehicle is stationary; 3. N is the neutral gear, used for temporary stops such as waiting at traffic lights, and the handbrake should be pulled up at the same time; 4. S is the sport gear, suitable for overtaking; 5. D is the drive gear; 6. L is the low gear, used when the vehicle is going downhill.
8
4
Share

How to Release the Steering Lock System?

Turn the steering wheel while turning the key to start the car. Alternatively, press the one-button start first, then step on the brake and turn the steering wheel. For example, if there is a malfunction in the steering lock function, the key is out of battery, or a wire has poor contact, etc., contact a 4S dealership.
15
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.