What Causes Engine Oil Leaks?

1 Answers
MacMaddox
07/29/25 6:15pm
Engine oil leaks can be caused by the following reasons: 1. Damaged or displaced sealing gaskets; 2. Improper installation of sealing components not following specified procedures; 3. Overfilling of lubricating oil or using incorrect oil type; 4. Prolonged engine use leading to aging and failure of sealing components; 5. Excessive pressure difference between engine interior and exterior. Solutions include: 1. Tightening various fastening nuts as required and according to specifications; 2. Timely replacement of failed sealing components; 3. Proper oil maintenance to prevent sludge buildup that may clog internal check valves or breather valves; 4. Ensuring proper sealing of external connecting pipes. Frequent disassembly may cause fastening rings to loosen/break or rubber parts to stretch, reducing sealing effectiveness and leading to oil seepage.
Was this review help?
15
5
Share
More Forum Discussions

What Are the S and L Gears?

Here is the relevant introduction about the S and L gears: 1. L Gear: Never engage this gear during normal driving. When accelerating or decelerating during driving, the vehicle's gear remains in the low gear. Maintaining a low gear while accelerating uphill provides stronger power. When going downhill, the low gear can help slow down the vehicle. 2. S Gear: When the S gear is engaged, the engine speed increases, and the fuel injection volume changes. At the same time, the adjustable suspension comfort becomes stiffer, reducing body roll during turns and alleviating nose-diving when braking. The trade-off for these effects is increased fuel consumption due to higher engine speeds, but the vehicle's overall performance is enhanced.
4
2
Share

What is the battery model for Venucia T90?

Venucia T90 uses a 46B24L battery model with 12V output voltage, which is a lead-acid battery primarily composed of lead and its oxides, featuring sulfuric acid solution as electrolyte, manufactured by VARTA. Here are the main reasons for battery damage: 1. Not turning off vehicle electronics before engine shutdown, causing excessive instantaneous current during restart that damages the battery. 2. Leaving headlights on after parking, resulting in complete battery drain. 3. Modifying car circuits leading to excessive power load on the battery.
5
3
Share

How Many Cylinders Does the Focus Engine Have?

Focus is equipped with a 3-cylinder engine, with 4 valves per cylinder. The working principle of an automobile cylinder is to guide the piston to perform linear reciprocating motion within the cylinder. In the engine cylinder, air converts thermal energy into mechanical energy through expansion; in the compressor cylinder, gas is compressed by the piston to increase pressure, thereby providing a power source. Below is an introduction to the classification of cylinders: 1. Single-acting cylinder: Only one end has a piston rod. Air is supplied from one side of the piston to generate pressure, which pushes the piston to extend and produce thrust, and returns via spring or self-weight. 2. Double-acting cylinder: Air is alternately supplied from both sides of the piston, outputting force in one or two directions. 3. Diaphragm cylinder: Uses a diaphragm instead of a piston, outputting force in only one direction and resetting via spring. It has good sealing performance but a short stroke. 4. Impact cylinder: This is a new type of component. It converts the pressure energy of compressed gas into the kinetic energy of the piston's high-speed (10~20 meters/second) movement to perform work. The impact cylinder adds a middle cover with a nozzle and a drain port.
19
0
Share

Is it necessary to rotate front and rear tires?

Tire rotation between front and rear positions is necessary as wear patterns differ between them. Regular tire rotation is important. Below are specific details: 1. Generally speaking, for front-wheel-drive vehicles, since the front tires bear most of the forces during load-bearing, acceleration, steering, and braking, they wear out faster than rear tires, with a wear ratio that can reach 2:1. 2. In routine maintenance, frequent tire rotation helps ensure even wear, thereby extending tire lifespan. If signs of premature or irregular wear are observed, the rotation frequency may be appropriately increased. After rotation, a four-wheel alignment is required because it ensures the vehicle's suspension system and steering system are in standard condition.
7
3
Share

How to Reset the Maintenance Reminder on the Volkswagen Lavida?

The steps to reset the maintenance reminder on the Volkswagen Lavida are as follows: 1. Turn off the ignition switch. 2. Press and hold the "0.0" button on the instrument panel. 3. Turn on the ignition switch while keeping the "0.0" button pressed. 4. Release the "0.0" button. When the message "Confirm to reset the service data" appears on the instrument panel display, press the "0.0" button again to confirm, and the maintenance reminder will be removed. Here is some related information about the Volkswagen Lavida: (1) The Volkswagen Lavida is a compact car under SAIC Volkswagen. The car has a length, width, and height of 4670mm, 1806mm, and 1474mm respectively, with a wheelbase of 2688mm. It features a MacPherson strut front suspension and a torsion beam rear suspension.
1
4
Share

What brand is the Mazda Atenza transmission?

The Mazda Atenza transmission is manufactured by Aisin. Below are some key details about Aisin: 1. Aisin transmissions are known for their smooth shifting, providing a seamless driving experience without noticeable jerks, and they are highly durable. 2. The Aisin 6AT transmission utilizes a dual planetary gear set, and its expanded lock-up range design helps reduce fuel consumption during upshifts. 3. Additionally, the fuel-saving valve incorporates advanced structural technology, optimizing fuel combustion efficiency both during idling and acceleration. 4. Moreover, the torque converter is equipped with a long-stroke damper, effectively minimizing vibrations.
19
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.