What Causes Engine Exhaust Pipe to Spray Engine Oil?

2 Answers
Leanne
09/02/25 2:05am
Engine exhaust pipe spraying engine oil is caused by: 1. Failure of piston, cylinder liner, piston pin, or piston rings. The damaged parts need to be identified and replaced; 2. Severe wear between the valve stem and valve guide, or poor sealing, resulting in excessive clearance and oil leakage downward; 3. Some vehicle models have inherent design defects that cause slight oil dripping from the exhaust, which is not obvious and does not cause significant impact. The car exhaust pipe serves to reduce vibration and noise for the vehicle body, extending the lifespan of the exhaust muffler system. Its main material is stainless steel.
Was this review help?
5
1
Share
McMarcus
09/14/25 4:29am
When the engine's exhaust pipe sprays oil, I suspect it might be due to worn piston rings, which allow oil to seep into the combustion chamber, mix with gasoline, and eventually be expelled through the exhaust. Another possibility is a failed valve guide seal—aging or overheating can cause it to crack and leak oil. If the car is turbocharged, a damaged turbocharger seal could also allow oil to leak into the exhaust system. Additionally, a damaged cylinder head gasket might connect the oil passage. In any case, this issue should not be taken lightly, as it can lead to high oil consumption, air pollution, and even blue smoke from the tailpipe, affecting performance and safety. It's recommended to take the car to a repair shop for inspection as soon as possible and avoid delaying the fix.
Was this review help?
7
5
Share
Expand All
More Forum Discussions

Where is the Audi emergency gear release located?

Audi emergency gear release is located behind the ashtray. N (neutral) gear: Functions the same as the neutral gear in a manual transmission, used for temporary parking. Another function is that if the engine suddenly stalls while driving and you want to restart the engine while moving, you need to shift into N gear. Generally, shift into N gear when waiting at traffic lights. Remember not to coast in N gear with an automatic transmission vehicle. Because modern cars are no longer from the carburetor era, this method cannot save fuel and can easily damage the clutch and cause danger. P (parking) gear: Used when turning off the engine or when the car is stationary. As the name suggests, its function is for parking. When the vehicle is stopped, you need to shift into P gear before you can power off, remove the key, and lock the doors. When the gear is shifted into P, the vehicle's braking mechanism is locked, and even if the vehicle is parked on a slope, it will not move. Note that when using this position, the car must remain stationary; otherwise, the transmission may be damaged.
3
0
Share

Is the Vehicle Inspection Station Closed During National Day Holiday?

Vehicle inspection stations are closed during the National Day holiday, so vehicle inspections cannot be conducted. Timely Vehicle Inspection: Vehicles that fail to undergo annual inspection on time will not have the annual inspection sticker. Driving a vehicle without this sticker is illegal. It is essential to get your vehicle inspected at the vehicle management office within the stipulated time to avoid any impact on driving. Purpose of Vehicle Annual Inspection: The goal of annual inspection is to eliminate potential safety hazards in vehicles, reduce the occurrence of traffic accidents, and encourage regular vehicle maintenance by owners. If a vehicle fails the inspection, the relevant staff will inform the owner of the specific non-compliant items. The owner is then given a limited time to make the necessary repairs before the vehicle can be re-inspected.
18
1
Share

What is the RPM of an Audi A3 at 120 km/h?

Audi A3 at 120 km/h has an RPM of 2500-3500. Engine RPM: Generally, vehicles with larger displacement have lower engine RPM at the same speed. Additionally, higher gears also result in lower engine RPM. For fuel-efficient driving, it is advisable to use higher gears to reduce engine RPM and thereby lower fuel consumption. However, when overtaking, it is appropriate to downshift to increase engine RPM for stronger power output. Continuously Variable Transmission (CVT): Whether it's a manual transmission, AT automatic transmission, or CVT continuously variable transmission, the principle is the same. Among them, CVT transmission is more suitable for family use. Firstly, it lacks the transmission gears of an automatic transmission, resulting in no jerking sensation during gear shifts, and due to its linear power output, driving is very smooth. Secondly, the gear design of a CVT is very flexible, offering many more gear ratios compared to traditional transmissions, making it easier to achieve various gear ratios and performance in the transmission system. Thirdly, CVT transmissions have high mechanical efficiency, leading to lower fuel consumption in vehicles.
20
4
Share

What is the reason for the Civic's charging system check and the horn not working?

Civic horn not working may be due to contact erosion. Contact erosion: If the horn is pressed for a long time, it can easily cause the horn contacts to erode and generate impedance. The current flowing through the electromagnetic coil weakens, the electromagnetic suction decreases, and it cannot attract the armature to drive the diaphragm to vibrate normally, resulting in a hoarse sound or even no sound. However, when the horn is pressed continuously, if a strong instantaneous current passes through the impedance, it can still work normally, so it may work intermittently. Poor sealing can easily lead to moisture. Although the inside of the horn is sealed, if the sealing is not tight, fog may enter during car washing or there may be water vapor in the internal air space. Water vapor can easily cause the contacts to become damp and fail to work properly. Poor contact of the electromagnetic coil terminal: Some horns have internal electromagnetic coil enameled wire terminal connections made of aluminum metal rivet crimping, rather than firm soldering. If the insulating paint on the enameled wire end is not completely removed or the rivet crimping is not firm, it can easily cause a virtual connection fault, leading to poor horn performance.
5
2
Share

What Causes the Constant Beeping of BMW Front Radar?

Here are the reasons why the BMW front radar keeps beeping: License Plate Issues: Especially for the front radar, since it generally requires a wide detection range, the radar's ultrasonic waves are also fan-shaped. If the license plate frame is too large or the license plate is bent or deformed, it may enter the radar's detection range, causing false alarms and constant beeping. For this issue, we can remove the license plate frame, install the license plate separately, or go to a 4S shop to reset the license plate frame width using a diagnostic tool. If the license plate is deformed, restore it to a flat state before reinstalling. Additionally, it's best to install the license plate with a curvature similar to that of the bumper, ensuring it fits snugly against the bumper. Once properly fixed, it generally won't beep unnecessarily. This problem usually occurs with new cars or vehicles that have had their license plates reinstalled. Dirty Radar Sensor: This is also quite common. For example, after washing the car or driving on muddy roads in rainy weather, mud or rainwater may be detected by the radar on the bumper or directly cover the radar sensor. In winter, rainwater may freeze on the bumper or sensor. Even a small bee flying by could trigger an alarm.
14
3
Share

Why is the Volkswagen Bora's wiper making loud noise?

Volkswagen Bora's wiper making loud noise is due to aging wiper blades. Maintain cleanliness: When there are streak marks on the glass surface, the wiper blade may be dirty. You can sprinkle alcohol on a towel and wipe the surface of the wiper blade. Cleaning once a month can improve the performance of the wiper. Check the rubber: If the wiper makes abnormal noises during operation, it may be due to aging or cracks in the rubber blade. If the wear is not severe, you can use sandpaper to smooth out rough spots on the surface. Avoid sunlight: Park the car in a shaded area where it is not exposed to sunlight, such as a garage. Summer is a season that is particularly harsh on cars. Wiper blades are rubber products, and sunlight will only accelerate the aging process. Refill fluid: Adding plain water directly to the windshield washer fluid reservoir is not conducive to the maintenance of the windshield and wiper blades in the long run. To ensure the longevity of the components, always use proper windshield washer fluid. Refill the washer fluid in time to be prepared for unexpected needs.
11
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.