Browse

Antiques Collectibles Apparel Baby Kids Items Books， Movies And Music Electronics Free Stuff Garden Outdoor Health Beauty Home Goods Home Improvement Supplies Musical Instruments Office Supplies Pet Supplies Sporting Goods Ticket Toys Games Transportation Others

Used Cars New Cars Others

Business Crafts Design And Web Events Home Improvement Legal Lessons Personal Pets Photography Repair And Technical Support Wellness Writing， Translation， And Transcription Others

Activities & Groups Artists & Musicians Classes & Lessons Events Friendship & Networking Lost & Found Rideshare Sports Teams Volunteers Travel & Travel Partners Skills & Language Swap Other

What Causes Delayed Gear Shifting in Automatic Transmission Vehicles?

1 Answers

Frank

07/30/25 8:21am

It may be due to excessive viscosity of the vehicle's transmission fluid. It is recommended to check whether the transmission fluid needs to be replaced. Here is the relevant information: Principle of Automatic Transmission Structure: In an automatic transmission, the selection of gear ratios and shifting are performed automatically. The term "automatic" refers to the fact that each gear change in the mechanical transmission is achieved by a system that controls the shifting actuators based on signals reflecting engine load and vehicle speed. Points to Note: The principle of automatic shifting in automatic transmission vehicles relies on a hydraulic system that determines whether to upshift or downshift based on throttle input. Since hydraulic pressure response requires a certain amount of time, the shifting reaction in automatic transmission vehicles is relatively slow.

Was this review help?

15

2

Share

More Forum Discussions

Does a Noisy Tensioner Pulley Damage the Car?

A noisy tensioner pulley can damage the car and affect its normal operation. Here are the reasons for a noisy tensioner pulley: 1. Aging or damage to the internal bearings. In severe cases, the tensioner pulley may completely fail to function. 2. Damage to the tensioner pulley can cause timing belt misalignment, leading to ignition and valve timing disorders, engine shaking, difficulty starting, and even valve deformation upon starting. 3. If the generator belt tensioner pulley is damaged, the vehicle's generator may not work properly, and power steering may become ineffective. Below is additional information about the tensioner pulley: 1. The tensioner pulley is located on the engine's timing belt or timing chain, providing guidance and tension to both. 2. During the operation of the timing belt or timing chain, the camshaft drives the valves to open and close at the correct time, coordinating with the piston to complete the four processes: intake, compression, power, and exhaust.

Where is the VIN number located on the Wuling Hongguang S?

The VIN number of the Wuling Hongguang S is located under the front passenger seat. Lift the seat to find it. The VIN number, also known as the vehicle identification number, serves as the car's ID and cannot be altered. There are several locations on the vehicle where the VIN can be found, as described below: 1. Engine compartment: There is usually a metal vehicle identification plate fixed to the frame inside the engine compartment, which displays the VIN. 2. B-pillar body plate: Another body plate is typically located on the B-pillar on the front passenger side. This plate is usually not metal but a sticker affixed to the B-pillar. 3. Lower left corner of the windshield: Most vehicles have the VIN displayed in the lower left corner of the windshield. 4. Frame-stamped VIN: The location of the stamped VIN varies by brand and model and may require some time to locate.

How to Remove the Spark Plugs on a Hyundai Verna?

Steps for replacing the spark plugs on a Hyundai Verna: Open the hood, lift the plastic engine cover, remove the high-voltage ignition wires, and mark each cylinder's position to avoid confusion. Use a spark plug socket to remove the spark plugs one by one. While removing them, check for any external debris like leaves or dust and ensure they are thoroughly cleaned. Place the new spark plugs into the spark plug holes, hand-tighten them a few turns, and then use the socket to tighten them further. Reinstall the high-voltage ignition wires in the correct firing order, then secure the cover. Damaged spark plugs can directly cause issues such as electrical leakage in the ignition system, increased fuel consumption, reduced power, and most notably, difficulty starting the vehicle, affecting its normal operation. Severe spark plug erosion—indicated by pitting, damage, or melted electrodes—means the spark plugs are ruined and should be replaced.

What Causes the High and Low Pressure of a Car's Air Conditioning to Be Equally High?

The reason for the high and low pressure of a car's air conditioning being equally high is insufficient refrigerant (Freon) in the AC lines or excessive addition of refrigerant oil, leading to a shortage of refrigerant. Here are the troubleshooting methods for car air conditioning: 1. Release excess refrigerant. 2. Replace the receiver-drier. 3. Perform a thorough vacuum and refill with refrigerant. 4. Clean or replace the condenser, and inspect the fan motor and its circuit. Compressor maintenance includes the following methods: 1. Check if the refrigerant is sufficient, measure the temperature difference between the inlet and outlet pipes of the drier, and inspect using a manifold pressure gauge. 2. Clean the air vents and remove dust and dirt inside the cabin. 3. Check if the refrigerant level in the AC system is normal. 4. Inspect the condition of the compressor belt.

How to Release Windshield Washer Fluid in the Car?

The most direct method to release windshield washer fluid in a car is by spraying it out through the windshield wipers. Here are some related details about releasing windshield washer fluid: 1. If the windshield washer fluid is frozen, do not attempt to spray it. Running the windshield washer continuously for several seconds can cause the washer motor to overheat, leading to expensive repair costs. 2. If sunlight doesn't thaw the fluid, you can add some warm water (not boiling water) to the washer fluid reservoir. Once the fluid thaws, make sure to drain it completely to prevent it from freezing again. 3. Additionally, in colder weather, when adding windshield washer fluid to the car, if tap water has been previously added to the reservoir, ensure it is completely drained. Mixing windshield washer fluid with tap water can easily lead to freezing.

How to Reset the Subaru Yellow Warning Light?

Subaru's yellow oil warning light may be caused by issues such as low oil level. To reset it, the underlying problem must be resolved. Check if the oil level is low or if the oil hasn't been changed on time and has deteriorated. Other related causes include: aging oil pump internal leakage, relief valve pressure release, bearing wear pressure release, or clogged filter. If any issues are detected, the vehicle should be sent to a workshop for inspection and repair. Additional relevant information is as follows: 1. The Subaru Forester's body dimensions are 4560mm in length, 1780mm in width, and 1700mm in height, with a wheelbase of 2615mm and a front-engine four-wheel-drive layout. 2. In terms of exterior design, this vehicle is equipped with high-brightness LED headlight assemblies, providing better visibility for the driver. The fog light area features more chrome trim for decoration, and the rear adopts C-shaped taillights.

Trending Ranking

What is a Motorcycle Quick Shifter System?

The Difference Between Double White Solid Lines and Single White Solid Lines

Which country is the Porsche brand from?

What does 1113 mean on a tire?

How to Remove 502 Glue from a Car?

Is the Changan Oushang X7 equipped with the Blue Whale engine?

Why Does the Engine Leak Oil?

Why does the Baojun 560 electronic steering lock malfunction?

How Should Beginners Who Just Got Their Driver's License Practice Driving?

How to turn off the fog lights on an Audi Q5 with automatic headlights?

More Forum Discussions

How long does it generally take to drive 40,000 kilometers?

How to Remove Adhesive Residue Left by Film?

How often should car air conditioning refrigerant be recharged?

How to Operate the Brake Pedal After Driving Through Water

Help

Cookie

Cookie Settings

© 2025 Servanan International Pte. Ltd.