What Causes Car Body Shaking at 120 km/h?

2 Answers
PaigeLynn
07/25/25 7:16am
The reasons for car body shaking at 120 km/h include excessive engine carbon deposits or component aging, as well as ignition system failures. Pre-departure vehicle inspection: Before setting off each day, conduct a comprehensive vehicle check, including checking for oil or water leaks, measuring tire pressure to ensure it's appropriate, inspecting engine oil condition to verify its color is normal and the oil level is correct. Safe driving: Use seat belts correctly - their protective effect during violent collisions is no less than that of airbags. Avoid fatigue driving and take breaks every 2 hours. Traffic rule compliance: Especially on highways, don't speed. Speeding not only risks traffic police penalties but more importantly is unsafe.
Was this review help?
14
2
Share
DelGabriel
08/10/25 6:28pm
My car starts to shake when it reaches 120 km/h, and I've encountered this issue several times. The main cause is usually related to the tires. The most common reason is improper wheel balancing, especially after changing tires or patching them without rebalancing. At high speeds, it can shake like a massage chair. Other causes include uneven tire wear, inconsistent tire pressure on both sides, or even slight wheel rim deformation, all of which can lead to shaking. Once, after changing tires, I noticed shaking at high speeds, and it was only resolved after rebalancing and a four-wheel alignment. Additionally, bulging or aging/deformed tires are worth checking, especially for cars that frequently drive on rough roads. If none of these are the issue, then it might be necessary to inspect the suspension system.
Was this review help?
13
5
Share
Expand All
More Forum Discussions

What Can Someone Do with a Found Driver's License?

Someone who finds a driver's license can: use it to deduct points in place of their own license. Below are the relevant precautions regarding the replacement of a driver's license: 1. Required documents: Bring your ID card, two recent one-inch white-background color photos without hats, and if the license was not issued in your registered residence, also bring a temporary residence permit or residence certificate, to the vehicle management office where the license was issued to complete the replacement procedures. 2. Application restrictions: During the period when the motor vehicle driver's license is legally seized, detained, or temporarily suspended, the motor vehicle driver is not allowed to apply for a replacement. After the motor vehicle driver replaces the motor vehicle driver's license, the original motor vehicle driver's license becomes invalid and must not be used anymore.
16
4
Share

Can Peterbilt Trucks Be Driven on Roads in China?

Peterbilt trucks can be driven on roads in China, but an A2 or A1 driver's license is required. Additional information: 1. Peterbilt: The Peterbilt 389 heavy-duty truck tractor, produced by the American company Peterbilt, played the role of "Optimus Prime" in the Transformers film series. The vehicle dimensions are 9.4 meters × 2.4 meters × 4 meters. 2. About Peterbilt Company: Peterbilt Company is a subsidiary of PACCAR Inc. Since its founding in 1939, it has established its dominance in the production of high-quality trucks in the United States. The company is headquartered in Washington State and holds about 10% of the heavy-duty truck market in the U.S. Peterbilt and Kenworth are the two flagship brands under PACCAR Inc. The perfect combination of innovation and classic design makes them the most representative American-style long-nose heavy-duty trucks.
13
4
Share

What is the difference between BMW's S gear and Sport mode?

BMW Sport mode and S gear differ in the following ways: Sport mode combines chassis and transmission programming. In high-end models abroad, Sport mode includes a heavier steering wheel, stiffer suspension, and the transmission logic shifting into S gear. However, domestic models lack dynamic chassis systems, so Sport mode only results in a heavier steering wheel and the transmission logic shifting into S gear, with Sport+ additionally disabling DSC. On the other hand, engaging S gear solely involves changes in transmission logic, specifically preventing automatic upshifting to the highest gear, shortening shift times, and reducing throttle lag. Therefore, S gear is only a part of Sport mode. Additional information: 1. Sport mode: As the name suggests, Sport mode enhances the engine's power output and driving dynamics for a more sporty experience, delivering the ultimate BMW-style driving thrill. 2. S gear: This refers to the S gear under the M/S position on the left side of BMW's electronic gear lever, also known as Sport mode, which is activated by shifting gears.
5
2
Share

How to Replace the Battery in a Jeep Electronic Key?

The method to replace the battery in a Jeep electronic key is: 1. After taking out the car key, remove the mechanical key. The mechanical key can be pulled out by pressing a small button; 2. Take out the car key and use a small flat-head screwdriver to pry open the car key. There is a small gap in the middle of the key, and it can be gently twisted open; 3. Use the small flat-head screwdriver to pry out the old battery, install the new battery, and then reassemble the key. When disassembling, be careful not to use excessive force to avoid damaging the key's shell and internal chip. Also, pay attention to the orientation of the battery when replacing it. Taking the Jeep Compass as an example, the vehicle's body dimensions are 4424mm in length, 1819mm in width, and 1635mm in height, with a wheelbase of 2636mm. The vehicle features a seven-slot chrome-plated grille flanked by square-shaped headlights and high-intensity projection fog lights, creating a streamlined and slightly aggressive front-end design.
2
0
Share

Does replacing an old ABS pump require matching?

Replacing an old ABS pump requires matching. Without proper matching, the ABS warning light will not turn off, and the part numbers must be consistent. The matching process can be efficiently completed using a 5054 tool. Additionally, both the ESP and tire pressure monitoring systems need to be configured to achieve perfect matching. How ABS works: During braking, ABS rapidly determines whether a wheel is locking up based on speed signals from each wheel speed sensor. It then closes the normally open input solenoid valve for the wheel that is starting to lock, maintaining the braking force. If the wheel continues to lock, the normally closed output solenoid valve opens, allowing brake pressure to rapidly decrease as the brake fluid flows directly to the reservoir, preventing the wheel from completely locking due to excessive braking force. This keeps the braking state at the optimal point (with a slip ratio S of 20%), ensuring the best braking performance and maximum driving safety. Classification of ABS: ABS is primarily categorized by channels. In ABS systems, brake lines that can independently regulate brake pressure are referred to as control channels. ABS systems are classified into four-channel, three-channel, two-channel, and one-channel configurations. One-channel ABS: Also known as single-channel ABS, it features a single brake pressure modulator in the rear wheel brake line and a wheel speed sensor installed on the rear axle differential (or one sensor on each rear wheel in some cases). Two-channel ABS: This configuration struggles to balance directional stability, steering control, and braking efficiency, and is rarely used today. Three-channel ABS: This system independently controls the two front wheels, while the two rear wheels are controlled together based on the select-low principle (i.e., both wheels are controlled by one channel to ensure the wheel with less traction does not lock), also known as hybrid control. Four-channel ABS: Equipped with four wheel speed sensors, this system has a separate brake pressure modulator in the brake line to each wheel, allowing independent control and forming a four-channel control configuration.
7
3
Share

Will the Car Door Lock Automatically If Not Locked?

No. Below is relevant information: How a car works: When the key is removed to cut off the power and the car door is closed, it is generally the driver who actively locks the car using the remote key. The reason is that most models on the market do not have the function of detecting the distance of the key's electronic signal. Additional information: Precautions: 1. Try to use the mechanical key to lock the car: When locking the car, it is still advisable to use the mechanical key, as this makes any signal jammer ineffective. If you don't mind the inconvenience, using the mechanical key more often can also save power and is safer than using a smart key. When using the mechanical lock, make sure the car door is properly closed and you hear the sound of the entire car locking; otherwise, it means the car was not successfully locked. 2. Try to park in a guarded parking lot and ask for a parking receipt: When parking for a long time, choose a guarded parking lot and ask for a parking receipt. This way, if any issues arise with the vehicle, you can ensure no loss occurs. However, you should still lock the car doors. Generally, in formal parking lots, criminals are less likely to enter.
16
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.