What Causes Cadillac Lights to Stay On After Locking?

1 Answers
OFernando
07/24/25 2:05pm
Cadillac lights may remain illuminated after locking due to the following reasons: 1. Replace the brake switch: A short circuit in the brake switch can cause the tail lights to stay on, necessitating replacement of the brake switch. 2. Insufficient brake fluid: After the car stops, the brake pads may fail to return to their original position, resulting in the tail lights remaining lit. 3. Wear: When the brake pads wear to a certain extent, the tail lights may stay on continuously. Below is an introduction to tail lights: 1. Types: Tail lights include rear fog lights, brake lights, reverse lights, rear turn signals, and rear position lights. 2. Precautions: If the tail lights malfunction, it is necessary to promptly inspect the lighting system and replace the faulty components. When a tail light bulb is damaged, the tail light assembly must be removed to replace the bulb.
Was this review help?
1
4
Share
More Forum Discussions

What Transmission Does the Lingpai Use?

The Lingpai is equipped with a CVT continuously variable transmission and a 6-speed manual transmission. The CVT transmission is commonly found in Japanese models, with its greatest advantage being smooth operation. Vehicles using a CVT transmission do not experience the jerking sensation during gear shifts, significantly enhancing the car's stability and comfort. More details are as follows: 1. The CVT transmission offers excellent fuel economy because it can select the most appropriate gear ratio based on the engine's operating conditions. During operation, the transmission achieves better fuel efficiency at all times. Compared to other types of transmissions, the CVT's transmission efficiency ranges between 90-97%. 2. The working principle of a manual transmission involves shifting the gear lever to engage different gear combinations with the power output shaft, thereby altering the torque and speed of the drive wheels. Compared to a 5-speed manual transmission, the 6-speed manual transmission has an additional gear, allowing speed variations to switch among these six gears. Consequently, the transmission's gears are more closely spaced, making the shifting process smoother and improving both the engine's fuel economy and performance.
2
2
Share

Which city is represented by the license plate 'Hei S'?

Heilongjiang Province does not have a 'Hei S' license plate; 'Hei S' is likely a fictional license plate used in film and television productions. More license plates in Heilongjiang Province are as follows: 1. Heilongjiang Province (Hei), License Plate Regions, Hei A Harbin City, Hei B Qiqihar City. 2. Hei C Mudanjiang City, Hei D Jiamusi City, Hei E Daqing City, Hei F Yichun City. 3. Hei G Jixi City, Hei H Hegang City, Hei J Shuangyashan City, Hei K Qitaihe City. 4. Hei L Songhua River Region (merged into Harbin City, license plates unchanged), Hei M Suihua City. 5. Hei N Heihe City, Hei P Daxing'anling Region, Hei R Agricultural Reclamation System.
10
2
Share

What Causes the Front Wheel of a Motorcycle to Make Noise?

Noise from the front wheel of a motorcycle may occur because the new brake pads and the contact surface of the brake disc have not yet fully worn in. Additionally, if there are hard spots on the brake pads, friction can be generated during semi-engagement, resulting in noise. Alternatively, after some use, as the brake pads and brake disc fully wear in, the noise may gradually disappear. This is a normal phenomenon. More details are as follows: 1. Electric motorcycles run slower than fuel-powered motorcycles and tend to have more issues than regular electric bikes. Generally, it's best to charge an electric motorcycle once every 20 days or so. 2. Each time you charge, it's advisable to continue charging for an hour after the light turns from red to green, but not exceeding 2 hours. If the light hasn't changed after 8 hours, stop charging and have it inspected at the manufacturer's repair center to determine whether the issue lies with the battery or the charger.
6
4
Share

What model is the Lancer in Mitsubishi?

Mitsubishi Lancer is a compact sedan. The first generation of Lancer was introduced in 1973, primarily designed to fill the gap between the MINIca and the Galant. The high-performance version of the Mitsubishi Lancer is the Evo, which is a compact sports sedan. Here are some relevant details: 1. Market Price and Positioning: The suggested retail price is quite affordable, making it suitable for general family use or as a daily driver for young people. 2. Configuration Parameters: This model is equipped with a 2.0-liter turbocharged engine, delivering a maximum power of 280 horsepower and a maximum torque of 355 Nm. The maximum power is achieved at 6,500 rpm, and the maximum torque is achieved at 3,500 rpm.
6
1
Share

How to Remove the Negative Terminal of a Car Battery?

Steps to remove the negative terminal of a car battery: 1. First, open the two fastening buttons of the thermal insulation cover and lift the red and black insulating covers over the positive and negative terminals. 2. Then locate the tightening nut of the negative terminal. 3. Finally, use a wrench to loosen the tightening nut of the negative terminal, then gently pry open the fastening block with a flat-head screwdriver. At this point, you can directly pull out the negative terminal. More details are as follows: 1. When removing, always follow the 'negative first, then positive' sequence (the opposite of the installation order). This is because, without removing the negative terminal first, the car's electrical circuit remains in a closed loop. If the positive terminal is removed while the negative is still connected and accidentally touches any metal part of the car, it is equivalent to connecting the positive and negative terminals of the battery. This not only causes a short circuit in the car battery but may also lead to sparking in severe cases. Therefore, extra caution is required during removal. 2. Generally, the electrical system of a car is characterized by: single-wire system, direct current, low voltage, and negative grounding. Low voltage and direct current refer to the 12-volt DC power supply. The single-wire system and negative grounding mean that other electrical devices on the car body are connected to the negative power supply through the metal body. 3. Under this circuit configuration, any contact between the battery and the car's metal parts is equivalent to connecting the positive and negative terminals, leading to a short circuit in the wiring and potentially causing significant damage to the battery and circuit wires. Hence, the rule of removing the negative terminal before the positive when disconnecting the battery. Similarly, when installing the battery, if the negative terminal is connected first and then the positive, any contact between the car body and a metal wrench can also cause a short circuit in the car battery wiring.
20
0
Share

What Needs to Be Checked During a New Car Inspection?

The inspection process for a new car at the inspection site is as follows: 1. First, visually inspect the car's paint surface to check for scratches, spots, dents, and wear. Observe the paint under sufficient sunlight to see if there is any color difference. Open the car door and push it from several angles to allow light to shine from different directions, checking if the sheet metal is smooth and if there are any signs of repair. 2. Check the vehicle's nameplate, which is located on the side of the driver's door or in the engine compartment. Pay attention to whether the manufacturing date is too far in the past. If it exceeds six months, the car is likely a stock vehicle or a test drive car. Also, ensure that the information on the nameplate matches the vehicle's certificate of conformity. 3. Inspect the windshield. The numbers represent the most recent production year, and the dots represent the production month. If the dots are on the left side of the number, it indicates production in the first half of the year; subtract the number of black dots from 7 to get the specific year. If the dots are on the right side, it indicates production in the second half of the year; subtract the number of black dots from 13 to get the specific year. If the windshield glass is far from the new car's production date (a year or more), it is likely that the windshield has been replaced. 4. Open the engine hood and check if the engine compartment is clean. If the car has been stored for a long time or used, some areas may show obvious dust or stains. Also, check if the engine oil is sufficient and if the levels of other fluids are within the acceptable range. 5. Open the car door and note whether the door opens and closes smoothly and flexibly, whether the door hinges make any noise, whether the gaps between the door and the front and rear bumpers are consistent, and whether the door can be closed in one step. 6. Check the tire production date. Since tires are purchased separately, their production date will naturally differ from the car's production date, which is not a major concern. However, if the tire production date is significantly older than the car's pickup date, it is worth noting. 7. Check the car's basic functions, such as whether the windows roll up and down normally, whether the air conditioning cools, whether the air vents emit any odors, whether the dashboard functions operate normally, whether the wipers work properly, whether the lights turn on correctly, and whether the sunroof opens and closes smoothly. 8. Test-drive the car. If allowed to start the engine, observe whether the engine idles smoothly, whether the steering wheel vibrates noticeably, whether the front and rear seats vibrate significantly, and whether there is any noticeable noise inside the car.
3
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.