What Causes Abnormal Noises When Shifting Gears in a Car?

1 Answers
McAndres
07/29/25 9:48pm
Abnormal noises during gear shifting in a car are most likely caused by poor performance of related components in the vehicle's drivetrain system. These components include the clutch, transmission, and drive shaft, among others. However, diagnosing issues related to abnormal noises and sounds in a vehicle requires an on-site test drive to listen and assess the sounds. A comprehensive analysis must be conducted, taking into account the conditions under which the noise occurs, the characteristics of the sound, and its source, in order to make an accurate diagnosis. Therefore, it is recommended that you take your vehicle to a specialized repair shop for further on-site inspection and analysis based on the above considerations and the actual condition of your vehicle.
Was this review help?
13
5
Share
More Forum Discussions

Why does the engine shake and the car not move when stepping on the accelerator?

The reasons for the engine shaking and the car not moving when stepping on the accelerator are as follows: Engine misfire: Engine misfire mainly refers to one or more cylinders of the engine not working properly. It is usually manifested as intermittent exhaust gas flow and severe shaking of the exhaust pipe, with noticeable engine vibration, sometimes accompanied by a sputtering sound. This is mostly related to ignition coil failure. Engine mount aging or loosening: Engine mounts are rubber blocks placed between the engine and the frame. Their function is to reduce vibration and buffer the engine's operation and to secure the engine. Once these mounts age or loosen, the engine's vibration will become unusually severe. Replacing the engine mounts can significantly reduce this effect. Carbon buildup issue: Cars inevitably face carbon buildup problems, including carbon deposits in the cylinders, throttle body, spark plugs, and intake system. When there is excessive carbon buildup inside the engine, the ignition energy, intake efficiency, and air-fuel mixture ratio will be affected, leading to unstable power output and shaking during idling and acceleration. It is recommended to have the engine cleaned at a 4S shop. Fuel system failure: Adding incompatible fuel grades can cause a decrease in the car's output power and reduced performance. Alternatively, if the fuel tank cap vent is blocked, or the fuel tank switch, fuel filter, or the fuel line between the tank and the carburetor are partially blocked, the required fuel supply cannot be met, resulting in a lean mixture and engine shaking. It is recommended to use the fuel grade specified by the manufacturer and perform regular maintenance.
3
4
Share

What is the actual fuel consumption of the Santana 1.5?

The average fuel consumption of the Santana 1.5 is around 6.2L. Here is some related information about the Santana: 1. Introduction: The Santana (SANTANA) sedan is a brand car produced by Volkswagen in the United States. Since 1985, after more than 20 years of production history, the ordinary Santana sedan (Santana 87) can be seen all over the country. 2. New Santana: The new Santana completely abandons the boxy design of the old Santana from the 1970s, replacing it with a more modern and stylish dynamic design, which is already the latest appearance of the Volkswagen family.
2
4
Share

Methods for Removing Old Car Paint

Methods for removing old car paint are as follows: 1. Manual Paint Removal Method: The manual paint removal method is commonly used in painting operations and is the only method for partially removing old paint films. It mainly relies on tools such as scrapers, putty knives, wire brushes, and sandpaper to remove old paint from the surface of vehicle body components. 2. Mechanical Paint Removal Method: The mechanical paint removal method uses electric or pneumatic tools, such as wire wheels, wire sanders, and dry/wet sandpaper sanders, to replace manual scraping and sanding. This method not only improves work efficiency but also reduces labor intensity, making it a widely used paint removal method in the vehicle body repair industry.
4
1
Share

What is the tire model specification of the Venucia T70?

Venucia T70 has two types of tires: 215/55R18 and 215/60R17. The first number 215 indicates the tire width is 215MM, 55 represents the aspect ratio of the tire section is 55%, meaning the section height is 55% of the width. The letter R stands for radial tire, and 18 denotes the rim diameter is 18 inches. The Venucia T70 has a top speed of 180km/h, accelerates from 0-100km/h in 11.5 seconds, and has a fuel consumption of 7.2L per 100km. In addition to the model, tires are also marked with the following common data: Tire cord material: Indicated by Chinese Pinyin, such as M-cotton cord, R-rayon cord, N-nylon cord, G-steel cord, ZG-steel radial cord tire. Speed rating: Indicates the maximum speed at which the tire can carry a specified load under specified conditions. Letters A to Z represent the certified speed ratings from 4.8km/h to 300km/h. Commonly used speed ratings include: Q: 160km/h; H: 210km/h; V: 240km/h; W: 270km/h; Y: 300km/h; Rim specification: Indicates the rim specification compatible with the tire for practical use, such as "Standard rim 5.00F".
7
3
Share

What is Subject Four Called?

Subject Four, also known as the Subject Four theoretical test or driver's theoretical test, is part of the assessment for obtaining a motor vehicle driver's license. Here are the specific details about the Subject Four test: 1. Number of Questions: The Subject Four question bank for small vehicles contains 1,240 questions, while the question bank for large vehicles has 1,715 questions. 2. Question Types: The test includes knowledge related to safe and civilized driving requirements, safe driving skills under complex conditions, and emergency handling, which were originally part of Subject One. These topics are now separated and conducted after the actual road driving test of Subject Three to further assess the traffic awareness of the candidates.
10
1
Share

Which Material is Best for Spark Plugs?

There are many types of automotive spark plugs, and it is recommended that car owners choose spark plugs reasonably based on their vehicle usage. Here is relevant information about spark plug types: 1. Standard Spark Plugs: The insulator skirt is slightly recessed into the shell end face, and the side electrode is outside the shell end face. This is the most widely used type. 2. Projected Insulator Spark Plugs: The insulator skirt is longer and protrudes beyond the shell end face. They offer advantages such as greater heat absorption, better anti-fouling capability, and direct cooling by incoming air to reduce temperature, making them less prone to hot spots and thus suitable for a wide thermal range.
20
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.