What Causes a Tire to Feel Bulged but Not Visible?

1 Answers
MacRowan
07/29/25 1:05pm
Here is a detailed introduction to the reasons why a tire may feel bulged but not visibly so: 1. Puncture or impact damage: Check if there is any puncture or impact damage on the tread or sidewall corresponding to the bulge. If found, have it repaired at a professional tire repair shop. The principle is that when a cord in the fabric breaks, under the pressure, it gradually pulls out from its original position, causing a sidewall bulge. This phenomenon will become visibly noticeable later, appearing as a radial bulge. 2. Joint of the tire body cords: If there is no damage at the corresponding location and the bulge can only be felt by hand, not visibly obvious when inflated, it is likely the joint of the tire body cords, which does not affect usage. 3. Delamination of components: If the bulge is circular, it should be claimed at the tire dealer or 4S store as it is a quality issue—delamination between rubber components or between rubber components and the tire body cords.
Was this review help?
15
2
Share
More Forum Discussions

What are the gear positions for the Honda Vezel automatic transmission?

The following is an introduction to the gear positions of the Honda Vezel automatic transmission: 1. P (Park): When this gear is engaged, the transmission locking mechanism activates, so it should only be engaged after the vehicle has come to a complete stop. 2. R (Reverse): This gear is used for reversing the vehicle. It can only be engaged after coming to a complete stop by pressing the brake and cannot be engaged while driving. 3. N (Neutral): Generally used for short-term parking, with the engine in an idle state. 4. D (Drive): One of the most commonly used forward gears, where the transmission shifts automatically. 5. S (Sport): The transmission delays shifting, keeping the engine at higher RPMs for better power response. Sport mode can be used when overtaking. 6. L (Low): Low gear is one of the forward gears, suitable for long or steep downhill slopes, but care should be taken not to let the engine RPM get too high.
13
4
Share

Where is the rear door handle of the Honda Vezel located?

The rear door switch of the Honda Vezel is located on the C-pillar. Designing the door handle here enhances aesthetics and reduces air resistance. Below are relevant details: 1. Introduction: The Vezel's space layout follows the "SMART CROSS PACKAGE" design philosophy, which highly integrates the personal privacy space of a coupe with the practical space of an MPV. Additionally, benefiting from Honda's unique "MM" concept—maximizing (MAX) space for passengers and minimizing (MIN) space for machinery—the Vezel excels in spatial advantages. 2. Configuration: With a wheelbase of 2610mm, the Vezel ensures ample interior space for comfortable driving and riding, with legroom comparable to higher-class SUVs. The optimized width and angle of the A-pillars, combined with Honda's latest internally openable panoramic sunroof, create a bright and spacious interior experience. The rear seats feature a 6:4 split-folding design that can tilt and flip, enabling flexible and diverse space configurations to meet daily needs. With the rear seats folded, the Vezel can accommodate two 27-inch bicycles with their front wheels removed. The luggage compartment features a low platform and a large 1180mm opening, making loading and unloading easier while providing a premium and spacious cargo area.
17
3
Share

What is the ground clearance of the Emgrand S?

The minimum ground clearance of the Emgrand S is 193mm. The minimum ground clearance of the Emgrand S refers to the distance between the lowest point (excluding the wheels) and the supporting plane, which is used to characterize the vehicle's ability to pass over obstacles such as rocks and tree stumps without collision. The higher the ground clearance of the Emgrand S, the better its off-road capability. However, if the ground clearance is too high, the stability at high speeds will decrease. The Emgrand S is a compact SUV under Geely Auto. The dimensions of the Emgrand S are 4430mm in length, 1833mm in width, and 1573mm in height, with a wheelbase of 2700mm. Generally, the ground clearance of sedans ranges between 110mm and 150mm, while that of SUVs ranges between 200mm and 250mm. However, the ground clearance of the Emgrand S is not static; it also depends on the load condition. Therefore, changes in ground clearance should be considered based on the Emgrand S's load variations. When selecting a vehicle, ground clearance can be one of the reference factors. The choice should depend on the vehicle's intended use and the road conditions. For urban areas with well-paved roads, a vehicle with lower ground clearance can enhance stability and comfort. If the vehicle is frequently used in remote areas or on poor road conditions, a higher ground clearance may be preferred to avoid underbody scrapes or damage, considering the vehicle's off-road performance.
6
4
Share

What is the difference between Class I, Class II, and Class III vehicles?

The difference lies in passenger capacity and cargo weight. Below are the relevant details: 1. Introduction to the three vehicle types: A Class I vehicle is a complete truck with an enclosed cargo compartment. A Class II vehicle is a chassis with a cab but no cargo compartment, used for modifying specialized vehicles such as dump trucks, fire trucks, and truck cranes. A Class III vehicle is a chassis without a cab but may have its own undercarriage, used for modifying long-distance coaches. 2. Classification requirements for the three vehicle types: Generally, passenger cars and small buses with 7 seats or fewer, as well as small trucks with a load capacity of 2 tons or less, are classified as Class I vehicles. Buses with 8 to 19 seats and trucks with a load capacity of more than 2 tons up to 5 tons (inclusive) are classified as Class II vehicles. The height of a Class I vehicle's front end is less than 1.3 meters, which is why minivans are classified as Class II vehicles. The classification of toll road vehicles will continue to follow the Ministry of Transport's industry standards, uniformly divided into five classes from Class I to Class V, with the toll price conversion coefficient increasing sequentially. The toll price conversion coefficient for Class I vehicles is 1, while for Class II vehicles, it is 2.
16
2
Share

How to Choose Between Mazda6 Atenza 2.0 and 2.5?

Owners who pursue speed and handling should opt for the Mazda6 Atenza 2.5, while those who only need it for daily commuting and have no particular requirements for speed and handling can choose the Mazda6 Atenza 2.0. Below is an extended introduction: 1. Mazda6 Atenza Handling: The Mazda6 Atenza's handling is excellent, with smooth power delivery. The combination of the 6AT transmission, chassis, suspension, and other factors contributes to its outstanding performance. The steering is precise, feeling light at low speeds and becoming heavier during high RPMs and high-speed cornering, yet the accurate steering always instills confidence in the driver. 2. Mazda6 Atenza Advantages: The chassis has a high limit, and as a front-wheel-drive car, it controls understeer exceptionally well during high-speed cornering. The Mazda6 Atenza can even perform on the track. Once entering a corner, the rear can exhibit slight oversteer, with outstanding body limits and dynamic performance. The high aspect ratio tires provide clearer road feedback. These factors give the Mazda6 Atenza excellent driving pleasure, making it capable of handling city streets, highways, tracks, and mountain roads with ease, ranking as the best in its class for handling.
17
5
Share

What to Do About High Fuel Consumption in CS35?

Solutions for high fuel consumption in CS35 are as follows: 1. Abnormal engine operation causing increased fuel consumption: Faults should be promptly addressed to restore normal engine operation. 2. Regular vehicle maintenance: For example, frequently clean the air filter to ensure the engine breathes fresh air and maintains smooth intake system operation. Regularly inspect the ignition system and replace spark plugs periodically, as sufficiently strong ignition sparks ensure complete combustion. 3. The fuel system should also be cleaned regularly: Carbon buildup on the fuel injectors can cause needle valve sealing issues, leading to fuel leakage. The engine interior should also be cleaned of carbon deposits periodically, as excessive carbon buildup can cause inaccurate fuel control and increased fuel consumption. 4. Regularly check tire pressure to ensure it is at the normal level: Both underinflated and overinflated tires can increase fuel consumption. Regular checks should also be performed.
11
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.