···
Log in / Register

What Causes a Car Engine to Make Loud Noises?

3 Answers
StLandon
08/31/25 7:49am
Engine loud noises may be caused by engine oil, belts, water temperature, etc. The specific analysis is as follows: Engine Oil: If the vehicle's engine oil viscosity is too high, it can easily cause operational issues in the engine, reduce lubrication effectiveness, and lead to loud engine noises. Promptly visit a repair shop to check if the engine oil needs replacement. Belts: Check if the belts are loose. Loose belts can cause increased noise in the engine compartment. Water Temperature: If the engine noise is loud, it might be due to high water temperature. Check if the temperature gauge is normal and if there is any smoke in the engine compartment. Be sure to replace the coolant before winter.
Was this review help?
20
3
Share
GabrielaLee
09/13/25 4:08am
As a seasoned driver with years of experience, I find that loud engine noises are quite common. Sometimes it's due to insufficient or degraded engine oil, which leads to inadequate lubrication and increased friction, causing a humming sound. When the belt is loose or has aging cracks, it produces a sharp whistling noise. If there are cracks in the exhaust system or loose connections, you might hear a banging sound. Another possibility is aging or loose engine mount bushings, which can increase overall vibration noise while driving. I've encountered this a few times myself. First, I stop to check the oil dipstick—if the oil level is below the mark, I top it up with fresh oil. Then, I inspect the belt for signs of wear. If the problem persists, don't delay—engine damage isn't just about noise; it could also lead to safety hazards. Always consult a professional mechanic for a thorough check. Remember, regular oil changes and belt inspections are key to prevention.
Was this review help?
18
2
Share
Expand All
LeNatalie
10/27/25 4:53am
As an automotive technology enthusiast, excessive engine noise can be analyzed from different aspects. Insufficient engine oil or excessively high oil viscosity increases friction, resulting in a roaring sound. Insufficient tension or cracks in the belt system can cause sharp noises at high speeds. Damage or leaks in the exhaust tailpipe or muffler can produce a low gurgling sound. Bearing damage can generate grinding noises, especially when the timing chain is too loose, causing a rattling sound. Modern vehicles have electronic control systems, and ECU faults may lead to premature ignition and increased noise. Distinguish problems by noise type: clicking sounds often originate from the valve area, while thumping sounds may come from the cylinders. For safety, promptly visit a repair shop for diagnostic equipment checks to avoid engine overheating risks.
Was this review help?
6
5
Share
Expand All
More Forum Discussions

What Are the Essential Items on a Major Maintenance Checklist?

Replace engine oil and three filters, replace transmission fluid, replace generator and fan belts, replace spark plugs, replace brake fluid, replace power steering fluid, replace fuel filter element, inspect and replace tires, inspect and clean throttle body, check antifreeze, inspect and replace timing belt, inspect chassis, inspect and clean fuel injectors, check battery. Here is related information: 1. Vehicle Maintenance: Vehicle maintenance refers to the preventive work of regularly inspecting, cleaning, supplying, lubricating, adjusting, or replacing certain parts of a vehicle, also known as vehicle servicing. 2. The purposes are: The purposes of vehicle maintenance are to keep the vehicle clean and tidy, maintain normal technical conditions, eliminate potential hazards, prevent failures, slow down the deterioration process, and extend the service life.
5
0
Share

Should the speed be maintained above 20 throughout the entire Subject 3 test?

It is not necessary to maintain the speed above 20 throughout the entire Subject 3 test. Here is an introduction regarding the speed requirements for the Subject 3 test: 1. Gear and speed should match: When in first gear, the speed should be between 10–20 km/h; when in second gear, the speed should be between 20–30 km/h; when in third gear, the speed should be between 30–40 km/h; when in fourth gear, the speed should be above 40 km/h; when in fifth gear, the speed should not exceed 45 km/h. 2. Speed considerations for the Subject 3 test: During the Subject 3 test, it is important to maintain a consistent speed throughout, avoiding sudden acceleration or deceleration. Driving too slowly may cause the engine to stall, while driving too fast may result in penalties. Generally, the speed should not exceed 45 km/h or drop below 10 km/h.
14
1
Share

Why can't the Nissan Sylphy start?

The reasons why the Nissan Sylphy cannot start may include human operational factors such as a dead battery, empty fuel tank, or incorrect gear position; it could also be due to vehicle usage issues like improper fuel quality, lack of antifreeze, or excessive carbon buildup. The vehicle usage reasons are as follows: 1. Fuel quality issue: During a repair, it was found that the fuel tank contained water and mud. Using such fuel will inevitably damage the car. Therefore, car owners are reminded to always refuel at reputable gas stations and can carry a gauze to cover the fuel nozzle when traveling to filter out impurities. 2. Lack of antifreeze: Some car owners add water or inferior antifreeze to their cars, resulting in extremely cold winter conditions that freeze the entire water circuit, crack the engine, prevent the car's water pump from functioning, cause failure to start, and damage other engine components.
20
1
Share

What is the sequence of actions for getting off the car in Subject 3?

The sequence of actions for getting off the car in Subject 3 is: shift to neutral, pull the handbrake, reset the right turn signal, turn off the engine, release the clutch and brake pedals, unbuckle the seatbelt, and observe the left rear before getting off. Introduction to Subject 3: Subject 3 includes the road driving skills test and the safety and civilized driving knowledge test, which are part of the motor vehicle driver's license assessment. The content of the road driving skills test varies depending on the type of vehicle being licensed. Test Content: The road driving skills test for Subject 3 generally includes: preparation for getting on the car, simulated light test, starting, driving straight, gear shifting operations, changing lanes, parking by the side of the road, going straight through intersections, turning left at intersections, turning right at intersections, crossing pedestrian crossings, passing through school zones, passing through bus stops, meeting vehicles, overtaking, making U-turns, and driving at night. The safety and civilized driving knowledge test generally includes: requirements for safe and civilized driving operations, knowledge of safe driving under adverse weather and complex road conditions, emergency handling methods for situations such as tire blowouts, and knowledge of post-accident handling procedures.
9
3
Share

How to Align the Vehicle Correctly at the Entrance of the S-Curve in Subject 2?

To align the vehicle correctly at the entrance of the S-curve in Subject 2, ensure that the left and right sides of the vehicle are equidistant and perpendicular to the entrance of the S-curve. Below are the relevant details about the S-curve in Subject 2: 1. Practical Operation Method for the S-Curve in Subject 2: Before entering the left curve, drive the vehicle close to the right side, keeping the right side of the car aligned with the right line. When preparing to switch to the right curve, turn the steering wheel to the right, aligning the left front corner of the car with the left line until the vehicle safely exits the curve, then turn the steering wheel back to the right. 2. New Requirements for the S-Curve in Subject 2: Driving over the edge line results in failure; stopping midway also results in failure.
4
3
Share

When does the 30-second countdown start for hill start?

Hill start thirty seconds is counted from when the vehicle comes to a stop, and the vehicle must be started within 30 seconds. Below is an introduction to the related content of Subject 2: 1. Assessment content: The five assessment items are reverse parking, parallel parking, hill start, right-angle turn, and curve driving. 2. Requirements: Subject 2 requires 26 training hours, of which 2 hours are theoretical knowledge, so in practice, it is 24 hours. 3. After the vehicle stops: If the vehicle is not started within 30 seconds, it results in a failure. If the front bumper of the car or the front axle of the motorcycle is not aligned with the pole line and deviates by no more than 50 cm, 10 points are deducted. 4. After the vehicle starts: If the vehicle rolls back between 30 cm and 50 cm, 20 points are deducted.
16
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.