···
Log in / Register

What Causes a BYD Vehicle to Lose All Power?

5 Answers
SanGemma
07/29/25 8:51pm

The reasons for a BYD vehicle losing all power are as follows: 1. Battery failure: When starting the engine, the battery supplies a strong current to the engine, enabling the starter to operate and initiate the engine's first working cycle, while also providing power to the ignition system and fuel pump to keep the engine running. 2. Alternator failure: Once the engine is running, it drives the alternator, which not only supplies power to the entire vehicle but also charges the battery. A properly functioning alternator can fully perform its role when the engine is running normally. However, if the alternator fails, it cannot supply power to the vehicle's electrical components normally, nor can it charge the battery. Emergency solutions: 1. Push-starting: Push-starting is a very effective emergency starting method, but it is a last resort and should not be used frequently. This method can cause some damage to the engine and clutch, and should especially be avoided for automatic transmission vehicles. 2. Prepare jumper cables: To avoid being unable to charge the battery when it runs out of power, car owners should keep a set of jumper cables in the vehicle, which can be purchased at most auto parts stores. However, when connecting the jumper cables, it is crucial not to mix up the connection order.

Was this review help?
13
2
Share
BrodyAnn
08/14/25 6:28pm

I've helped friends deal with BYD vehicles losing all power several times, and it's usually a power system issue. The most likely causes are a completely drained or damaged battery – like leaving headlights or onboard devices on leading to discharge, especially worse in cold weather. It could also be an alternator failure, where the battery drains quickly after being charged. Blown fuses are another major culprit, particularly if the main power fuse burns out cutting the current. Loose, corroded, or short-circuited connections in the wiring can also cause sudden power loss.

Quick fixes: First check battery voltage – normal is above 12V, below 10V means replacement is needed. Try jump-starting from another vehicle. If systems work normally after starting, it's probably fine. But if it won't start or quickly loses power again, immediately visit a professional repair shop for full alternator and wiring checks.

My regular advice: Develop good habits – confirm all electronics are off after shutting down the engine, and periodically charge the battery to extend its lifespan. This can save you a lot of repair headaches.

Was this review help?
17
5
Share
Expand All
LeDerek
10/16/25 6:57am

With over a decade of driving experience, I've encountered numerous instances of BYD vehicles running out of battery. Common causes include battery aging, where the original battery needs replacement after a few years, or forgetting to turn off accessories like the radio overnight, which once left my friend's car completely drained. Generator failure is another frequent issue, causing the battery to deplete while driving. The simplest fix is replacing a blown fuse in the engine compartment's fuse box. Sudden power loss can also result from wiring issues like disconnected plugs or corrosion. In emergencies, try jump-starting with another vehicle's battery; if successful, drive to a BYD service center for charging system inspection. For new energy BYD models, battery management module faults may occur, but this method usually works for gasoline versions. I recommend weekly vehicle checks to prevent unexpected issues and ensure safer driving.

Was this review help?
10
4
Share
Expand All
MacMaddox
11/29/25 7:45am

A complete power loss in a vehicle is extremely dangerous, and this issue with BYD is often caused by power supply failures. The main reasons include a completely depleted battery, a faulty alternator unable to charge, or a blown fuse interrupting the current. Additionally, short circuits or broken wires may lead to unexpected power outages. Immediate and safe handling is crucial: pull over safely, turn on hazard lights, and check if the main fuse is intact. Call for a tow truck if necessary. Avoid forcing a start to prevent engine damage. Take the vehicle to a repair shop for a comprehensive diagnosis, especially focusing on the alternator and electrical system. Develop good habits: always turn off electrical devices when parking to avoid battery drain risks. Prevention is key to significantly reducing such troubles.

Was this review help?
18
5
Share
Expand All
OLorenzo
01/20/26 2:21am

Understanding the vehicle's electrical system, a complete loss of power is usually due to issues with the alternator, battery, or circuits. A faulty alternator means no power input to the battery; a depleted battery indicates its lifespan has ended; a short circuit triggers fuse blowout to protect the vehicle. For hybrid BYD systems, diagnosis might be more complex, but the standard version follows similar troubleshooting. First, test the battery voltage—a multimeter reading above 12 volts is normal, lower values require replacement; then inspect wiring for faults. Learning basic automotive knowledge is highly beneficial, such as how to manually jump-start in emergencies. This enables better prevention and response to unexpected situations.

Was this review help?
16
3
Share
Expand All
More Forum Discussions

What is the battery model for Peugeot 408?

Peugeot 408 is originally equipped with a Camel L2-400 battery. Camel batteries are produced by recycling used batteries, which undergo professional technical processing to regenerate materials such as recycled electrolytic lead, recycled alloy lead, and recycled plastics, forming new batteries. Battery usage precautions: 1. If a battery is left unused for a long time, it will slowly self-discharge until it becomes unusable. Therefore, the car should be started periodically to recharge the battery. 2. When the ammeter indicates insufficient charge, the battery should be recharged promptly. 3. The density of the electrolyte should be adjusted according to standards based on different regions and seasons.
2
3
Share

How to Reset the Maintenance Light on Mitsubishi Eclipse Cross?

The method to reset the maintenance light on Mitsubishi Eclipse Cross is as follows: 1. Turn the key to shut off the engine. 2. Locate the trip computer control button on the left side of the center console. 3. Press and hold the button for more than 5 seconds, then press the ignition button to start the vehicle. 4. The maintenance light reset is complete. Information about the maintenance light is as follows: 1. The function of the maintenance light is to record the mileage of important components, similar to a timer in a sprint race, serving as a reminder for the car owner and maintenance personnel. 2. Although the maintenance light does not affect the car's performance, it must be reset after maintenance; otherwise, the owner cannot accurately know the usage time of new components during the next replacement.
16
4
Share

What is the correct way to warm up a Mercedes-Benz GLA?

Mercedes-Benz GLA warm-up method: After starting the vehicle, let it idle to warm up. Wait until the coolant temperature rises by half a mark and the engine RPM stabilizes before driving off. Below is an introduction to warming up the Mercedes-Benz GLA: 1. After the engine is ignited, the oil pump in the oil pan also starts working, delivering oil to various parts of the engine. Components such as the crankshaft and connecting rods in the crankcase, the camshaft controlling the valves in the cylinder head, and the valve lifters are all in motion and require excellent lubrication. 2. It takes several tens of seconds for the oil in the oil pan to reach these parts. The time required varies depending on the engine design and oil fluidity, which should be the minimum time for "warming up" before driving off.
17
5
Share

What grade of gasoline should the Highlander use?

The Highlander should be refueled with 95 octane unleaded gasoline. Relevant information about the Highlander is as follows: 1. Interior: The Highlander's interior features a simple and elegant overall design with numerous buttons on the center console, but they are well-arranged for convenient operation. 2. Powertrain: The Highlander offers two powertrain options—a 3.5L V6 engine paired with a 5-speed automatic transmission and a 2.7L L4 engine paired with a 6-speed automatic transmission. 3. Space: The Highlander has a tall body, providing spacious and ample interior room. The second row can slide forward and backward by 120mm, and the middle seat can be freely removed or combined. The third row can also be folded down proportionally to increase space flexibility and expand the trunk capacity.
8
4
Share

What is the Pusan car?

Pusan refers to the standard version of the Santana, which is the abbreviation for the Volkswagen Santana 87 model, distinguishing it from the Santana 2000 and newer Santana models. Below is some related information about the Santana: 1. The Santana is equipped with 1.4L and 1.6L engines, codenamed EA211. This series of engines comes in two displacements, with the 1.4L engine delivering a maximum power of 66kW and the 1.6L engine delivering a maximum power of 81kW. Both engines feature a lighter all-aluminum structure. The transmission options include a 5-speed manual and a 6-speed Tiptronic automatic. The suspension setup consists of front MacPherson independent suspension and rear torsion beam non-independent suspension. 2. Higher-end models are equipped with ESP, cruise control, and leather seats. Some manual transmission models also come with automatic air conditioning.
16
2
Share

How to Adjust the Time on a Hyundai Verna?

The method to adjust the time on a Hyundai Verna is as follows: After turning on the car, press and hold the CLK button for about 5 seconds until the time display on the screen starts flashing. Use the adjustment buttons (turn left to decrease, turn right to increase) to set the correct time. Once adjusted, press the CLK button again to confirm. The adjustment mode will automatically exit after a few seconds of inactivity. Below are some relevant details about the Hyundai Verna: 1. In terms of appearance, the car has a wheelbase of 2570mm. 2. For the interior, the car features a simple T-shaped center console design with a clear layout and is equipped with a large touchscreen. 3. Regarding the powertrain, it is equipped with a 1.4L naturally aspirated engine, delivering a maximum power of 70kW (95PS) and a peak torque of 132N·m. The transmission system is paired with a 5-speed manual or a 4-speed automatic gearbox.
3
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.