What car brand has a single vertical line as its logo?

How to Use Turn Signals at Roundabouts?

When using turn signals at roundabouts, follow these methods: 1. When entering the roundabout and needing to merge into the inner lane, use the left turn signal. Before exiting the roundabout, signal right in advance, confirm safety, and then change lanes from the inner lane to exit the roundabout. 2. When staying in the outer lane while entering the roundabout, you may not need to use a turn signal. However, signal right when exiting the roundabout. Choose the middle lane within the roundabout if going straight. 3. When needing to turn right within the roundabout, use the right turn signal. Select the right lane inside the roundabout for a right turn. Alternatively, you can use the right turn signal from the outer lane. The situation when entering the roundabout is similar to going straight, so there's no need to use the left turn signal.

11

4

Share

Can You Still Drive When the Car Indicates an Oil Change?

You can still drive when the car indicates an oil change, but avoid driving long distances and replace the oil as soon as possible. The steps for changing the oil are: 1. Lift the car, remove the undercover, and place a container under the oil drain plug; 2. Unscrew the oil drain plug, use an air gun to blow for two minutes at the oil filler port, tighten the drain plug after draining, and wipe it with a tissue to check for leaks; 3. Reinstall the undercover, lower the car, and use a funnel to add new oil through the filler port. Precautions for changing the oil include: 1. Perform the change when the engine is warm to ensure complete drainage of old oil; 2. Ensure the correct amount of oil is added; 3. Start the engine after adding oil to check for leaks in all components; 4. After running the engine for 3 minutes, confirm the oil level is within the normal range.

14

1

Share

What is the matching method for the MG6 window regulator?

Before matching, first turn the ignition switch to the ON position. Press the switch to fully open the window. Pull up the switch to fully close the window, and after the window is completely closed, continue to hold for 2 seconds before releasing the switch. After resetting, the left front door window switch can control the window regulators of the other three doors. However, it is still recommended to go to a 4S shop or repair shop for matching to avoid damage to the car's window regulator caused by self-matching. Here is more information about window regulators: 1. The window regulator is the lifting device for car door and window glass, mainly divided into electric window regulators and manual window regulators. Nowadays, many car door and window glasses are generally switched to button-type electric lifting methods, using electric window regulators. Electric window regulators for cars are mostly composed of motors, reducers, guide ropes, guide plates, glass mounting brackets, etc. The master switch is controlled by the driver to open and close all door and window glasses, while the sub-switches on the inner handles of each door are controlled by passengers to open and close their respective door and window glasses, making operation very convenient. 2. If there is abnormal noise during the process of car window glass lifting, it may be due to insufficient lubrication of the window lifting guide rails or damage to the lifting components. It is necessary to clean the guide rails in time, add lubricating oil, and replace the lifting components. When matching the MG6 window regulator, first close the window, then pull the door window regulator switch twice in the lifting direction to complete the setting. If it doesn't work, please repeat this step. The same applies to other doors. All four windows are equipped with one-touch lifting function. When using it, lifting the window button again can make the window glass automatically rise completely. The four buttons control the four windows, and each button has two functions: one-touch lifting and point-to-point lifting.

17

4

Share

What is the tire model of Hyundai Elantra?

Elantra's tire model is 195/65r15. Below is relevant information about tire pressure: Tire Pressure: Both overinflation and underinflation will affect the service life of tires. Winter tire pressure can be slightly higher than summer tire pressure. Recommended summer tire pressure is between 2.2-2.5bar, while winter tire pressure should not exceed 2.8bar. Adjust the pressure appropriately according to load conditions. Underinflation: Insufficient tire inflation pressure can also cause excessive tire wear, poor vehicle control, reduced fuel economy, and may lead to wheel deformation. Therefore, tire inflation pressure should be maintained within the specified value. Overinflation: Excessive tire inflation pressure will result in uncomfortable ride, excessive wear in the center of tire treads, and increase the possibility of tire damage on hazardous road surfaces.

17

2

Share

What is the reason for the wrench icon appearing on the car dashboard?

The reason for the wrench icon appearing on the car dashboard is to remind the owner to perform car maintenance. The car maintenance items include: 1. Changing the engine oil and oil filter; 2. Replacing the oil filter element, air filter element, fuel filter element, air conditioning filter element, and transmission oil filter element; 3. Adding windshield washer fluid, antifreeze, and air conditioning refrigerant; 4. Checking whether the drive belt is worn; 5. Cleaning the throttle valve and carbon deposits in the cylinders; 6. Inspecting the chassis for damage; 7. Checking the body and tires. The functions of car maintenance: 1. Ensuring the vehicle's excellent performance condition; 2. Improving driving safety; 3. Reducing engine noise; 4. Extending the vehicle's service life.

4

Share

How to Use the Headlight Delay-off Feature on the Hyundai Elantra?

The method to use the headlight delay-off feature on the Hyundai Elantra is: 1. Enter the settings on the central control screen and click on the lights; 2. In the lights interface, you can see the option for headlight delay-off; 3. Simply set it up. Taking the 2020 Hyundai Elantra as an example, it is a compact car with body dimensions of: length 4610mm, width 1800mm, height 1450mm, wheelbase of 2700mm, and a body weight of 1319kg. The 2020 Hyundai Elantra is equipped with a 1.4T turbocharged engine, delivering a maximum horsepower of 130PS, maximum torque of 211Nm, maximum power of 95.6kW, and is paired with a 7-speed dual-clutch transmission.

4

Share

What car brand has a single vertical line as its logo?

How to Use Turn Signals at Roundabouts?

Can You Still Drive When the Car Indicates an Oil Change?

What is the matching method for the MG6 window regulator?

What is the tire model of Hyundai Elantra?

What is the reason for the wrench icon appearing on the car dashboard?

How to Use the Headlight Delay-off Feature on the Hyundai Elantra?

What symptoms will a car exhibit if the three-way catalytic converter has issues?

How to Fix Cigarette Burns on Car Seats?

What position should the car's rearview mirrors be adjusted to?

Why Does Gear Shifting from First to Second Feel So Jerky?