What can fog lights do?

1 Answers
LaAutumn
07/30/25 4:17am
Fog lights can make your vehicle visible to others in conditions of reduced visibility such as fog or heavy rain. Fog lights generally refer to automotive fog lights, which are installed at the front and rear of the vehicle. Due to low visibility in foggy weather, the driver's line of sight is limited. The lights can increase the visible distance, especially the strong light penetration of yellow fog lights, which enhances visibility for both the driver and surrounding traffic participants, allowing approaching vehicles and pedestrians to spot each other from a greater distance. Fog lights are divided into front fog lights and rear fog lights. Front fog lights are typically bright yellow, while rear fog lights are red. The symbols for rear fog lights differ slightly from front fog lights - the front fog light symbol features downward light lines, whereas the rear fog light symbol shows parallel lines, usually located on the vehicle's instrument control panel.
Was this review help?
7
5
Share
More Forum Discussions

How many kilometers should the timing belt of Elysee be replaced?

The manufacturer's recommendation for the Elysee timing belt is to replace it every 3 years or after driving approximately 60,000 to 80,000 kilometers. Below is detailed information about the car timing belt: Overview: The main function of the engine timing belt is to drive the engine's valve train, ensuring that the intake and exhaust valves open or close at the appropriate times, allowing the engine cylinders to properly intake and exhaust air. Additional Information: As the engine operating time increases, the rubber timing belt and other related components, such as the tensioner pulley, tensioner, and water pump, will experience wear or aging. Compared to traditional belt drives, chain-driven systems offer more reliable transmission, better durability, and space-saving advantages.
2
2
Share

How to Remove a Car Half Shaft?

And support with a jack. Remove the wheel and tire assembly. Remove the brake caliper assembly. Remove the cotter pin from the drive axle. Use a removal tool to detach the tie rod end ball joint from the steering knuckle. Remove the fixing nuts of the control arm to the steering knuckle and ball joint. Drain the drive axle lubricant. Pull the hub/steering knuckle assembly to separate it from the car, so that the drive shaft can be separated from the drive axle. Use a wheel puller to press the drive shaft out of the hub/steering knuckle assembly.
4
5
Share

How to Clean the Fuel Injectors of a Geely Emgrand?

Methods for cleaning the fuel injectors of a Geely Emgrand: 1. Open the hood and use a Phillips screwdriver to remove the fixing screws of the fuel rail; 2. Disconnect the battery cables and remove the fuel injectors from the fuel rail; 3. Connect the fuel injectors to a homemade fuel injector plug and wire, then clean them with carburetor cleaner. The Geely Emgrand is a sub-brand under the Geely parent brand, equipped with a 1.3T GeTec DVVT turbocharged engine. In terms of body dimensions, it measures 4631mm in length, 1789mm in width, and 1470mm in height, with a wheelbase of 2650mm.
8
0
Share

Why can't you make a U-turn on white dashed lines?

Because making a U-turn on white dashed lines can easily lead to traffic accidents. White dashed lines indicate pedestrian crossings, which are signs for pedestrians to pass through. Here is the relevant information: 1. White dashed lines: When marked on road sections, they are used to separate traffic flows in the same direction or serve as safe driving distance identification lines; when marked at intersections, they are used to guide vehicle movement. 2. Situations where U-turns are allowed: At locations with designated U-turn openings, drivers should turn on the left turn signal in advance and make the U-turn without affecting other normal traffic; at intersections with U-turn signals, ensure the U-turn signal is green and make the U-turn only within the designated lane; at intersections with U-turn signs, make the U-turn based on actual conditions without obstructing other vehicles or pedestrians, and at intersections without explicit prohibitions against U-turns or left turns.
2
1
Share

How to Add Windshield Washer Fluid to the New Buick Excelle?

Method for adding windshield washer fluid to the new Buick Excelle: The windshield washer fluid filler port is located at the lower right corner of the engine compartment, with the cap marked with a washer symbol. The washer fluid capacity is 4L, and it should be appropriately refilled based on the remaining amount. Windshield washer fluid is only consumed during use, so there is no fixed refill interval - simply top it up when the level is low. The Buick Excelle is another masterpiece launched by the Buick brand following the new Regal, new LaCrosse, and Enclave, based on the "global platform, European and American technology." The new Excelle adheres to Buick's "dynamic and smooth" design language, drawing inspiration from the classic elements of the Riviera concept car, featuring a body design that combines sportiness with sophistication.
12
0
Share

Is It Necessary to Replace a Leaking Front Motorcycle Shock Absorber?

Motorcycle front shock absorber leakage requires replacement. Below is relevant information about shock absorbers: Introduction: A shock absorber (Absorber) is used to dampen the oscillations from spring rebound after absorbing shocks and impacts from the road surface. Widely used in automobiles, it accelerates the attenuation of frame and body vibrations to improve ride comfort. When traversing uneven roads, although the suspension springs can filter out road vibrations, the springs themselves still undergo reciprocating motion, and the shock absorber is employed to suppress this spring bouncing. Working Principle: Most shock absorbers used in automotive suspension systems are hydraulic shock absorbers. Their working principle involves the piston inside the shock absorber moving up and down when relative motion occurs between the frame (or body) and the axle due to vibrations, causing the oil in the shock absorber chamber to repeatedly flow from one chamber to another through various orifices.
19
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.