What brand of tires does the Beijing Hyundai Elantra use?

1 Answers
MacHayden
07/29/25 11:21am
The Elantra uses Nexen tires. The tire specifications for the Hyundai Elantra are: 205/55R16 and 225/45R17. Nexen Tire was founded in 1942 and successfully produced Korea's first automobile tires in 1956. Since 2012, it has been supplying original equipment tires to global automakers, including Porsche, Volkswagen, General Motors, Skoda, Hyundai, Kia, Renault, FCA, Beijing New Energy Automobile, Suzuki, and many other global automotive manufacturers. For daily use of Hyundai Elantra tires, pay attention to the following points: Regularly check the tire surface for defects such as cracks or deformations. Due to driving wear, the tread grooves gradually become shallow. If the tread wears out, it will lose its drainage and anti-slip functions, significantly reducing the car's performance. Small cracks may become potential hazards for tire blowouts at high speeds. Additionally, promptly remove pebbles from the grooves; try to park on flat ground. Avoid parking on roads with thick, sharp, or pointed stones. Do not park near or in contact with petroleum products, acids, or other materials that may deteriorate rubber. After parking, the driver should not turn the steering wheel, as this accelerates tire wear; do not splash water for cooling. In hot weather or during high-speed driving, tires are prone to overheating, and tire pressure increases. In such cases, park to allow the tires to cool naturally. Never release air to reduce pressure or splash water to cool the tires, as this may cause abnormal aging of the tread rubber; avoid sudden braking. Try to minimize frequent use of brakes and sudden stops to prevent accelerated tread wear caused by dragging between the tires and the ground.
Was this review help?
3
4
Share
More Forum Discussions

Can motorcycles use the inner ring expressway?

No, motorcycles are not allowed on any expressways. Regulations regarding expressways: According to Article 51 of the Road Traffic Safety Law of the People's Republic of China: When a motor vehicle is in motion, the driver and passengers shall use seat belts as required, and motorcycle drivers and passengers shall wear safety helmets as required. Not wearing seat belts: Seat belts are an important safety device in vehicles to protect passengers. It is essential to fasten seat belts during travel, especially when driving on expressways. Without seat belts fastened, passengers could potentially be ejected from the vehicle at high speeds.
3
5
Share

Do I need to bleed the rear wheels after replacing the right front wheel brake caliper?

After replacing the right front wheel brake caliper, there is no need to bleed the rear wheels. Introduction to brake calipers: The brake caliper is an indispensable component of the braking system's chassis. Its main function is to push the brake pads, which then rub against the brake drum, slowing down or stopping the vehicle. When the brake pedal is pressed, the master cylinder generates thrust to push hydraulic fluid to the caliper. The piston inside the caliper moves under hydraulic pressure, pushing the brake pads. Hydraulic brakes consist of a master cylinder and a brake fluid reservoir. One end is connected to the brake pedal, and the other to the brake fluid lines. The master cylinder contains brake fluid and has inlet and outlet ports. Types of automotive brakes: Automotive brakes are divided into air brakes and hydraulic brakes. Air brakes consist of an air compressor, at least two air reservoirs, one master cylinder, one quick-release valve for the front wheels, one relay valve for the rear wheels, four brake calipers, four adjustment backs, four cams, eight brake shoes, and four brake drums. Hydraulic brakes consist of a master cylinder (hydraulic brake pump) and a brake fluid reservoir. Heavy-duty trucks typically use air brakes, while most passenger cars use hydraulic brakes. Therefore, the master cylinder and calipers in these vehicles are hydraulic brake pumps. The brake caliper (hydraulic brake pump) is an essential part of the braking system. When you press the brake pedal, the master cylinder sends hydraulic fluid through the lines to each caliper.
4
5
Share

Where are the traffic violation handling points on the Daguang Expressway?

The traffic violation handling locations for the Daguang Expressway are either the vehicle management office or traffic police team in the vehicle's registration place, or the vehicle management office or traffic police team in the location where the violation occurred. Required materials: If the violation was only captured by an electronic eye, only the vehicle license is needed; if it was a speeding violation, prepare the vehicle license, driver's license, and a copy of each; if it was a parking ticket, bring the penalty decision notice and the vehicle license. Paying the fine at the vehicle management office: After preparing the materials, go to the vehicle management office to check if the violation is genuine, review the photos, and then fill out a confirmation form. Take the confirmation form to the designated bank of the vehicle management office to pay the fine; any branch of the specified bank will do. Generally, this can be done at an ATM.
6
0
Share

What is the reason why the OBD cannot read data when registering a new car?

If the vehicle management office cannot detect the OBD, it may be due to instrument failure, incomplete data, or compatibility issues with the vehicle. Introduction to the OBD system: It is a detection system extended for automotive fault diagnosis. "OBDⅡ" stands for "onBoardDiagnosticsⅡ," which is the abbreviation for Type Ⅱ On-Board Diagnostics system. To standardize the diagnosis of emissions and drivability-related faults, starting from 1996, all new cars sold in the U.S. must have similar diagnostic instruments, fault codes, and repair procedures, i.e., comply with the OBDⅡ program regulations. With increasing economic globalization and automotive internationalization, the OBDⅡ system, as the foundation for drivability and emissions diagnosis, will be implemented and applied more widely. The OBDⅡ program simplifies and unifies automotive fault diagnosis, eliminating the need for maintenance personnel to learn each manufacturer's new system separately. OBD principle: The OBD system continuously monitors whether the vehicle's emissions exceed the standard during engine operation. If they do, it will immediately issue a warning. When a fault occurs in the system, the fault (MIL) light or the Check Engine warning light will illuminate, and the Powertrain Control Module (PCM) will store the fault information in memory. Through a specific procedure, the fault code can be read from the PCM. Based on the fault code's prompt, maintenance personnel can quickly and accurately determine the nature and location of the fault.
6
0
Share

Can 92 and 95 be mixed?

If the recommended gasoline for the vehicle is 92 octane or below, a mixture of 92 octane and 95 octane gasoline can be used, but it is not recommended for long-term use. If the recommended gasoline for the vehicle is 95 octane or above, a mixture of 92 octane and 95 octane gasoline cannot be used. If a high-compression-ratio engine uses low-octane gasoline, the gasoline engine is prone to knocking. Prolonged engine knocking can easily cause faults such as piston sintering and piston ring breakage, accelerating the damage to engine components. If a low-compression-ratio engine uses high-octane gasoline, although it can avoid engine knocking, the high-octane gasoline paired with a low-compression-ratio engine will alter the ignition timing, leading to increased carbon deposits in the cylinders. Long-term use will reduce the engine's lifespan. Whether it's 92 octane or 95 octane gasoline, both are gasoline mixtures. When these two different octane gasolines are mixed, they will blend, and the resulting gasoline's octane rating will definitely be between 92 and 95. For vehicles that can use 92 octane gasoline, it is equivalent to using a higher octane gasoline, which is fine in the short term. For vehicles that use 95 octane gasoline, it is equivalent to using gasoline with a lower octane rating than recommended, which is highly harmful and should not be used.
11
3
Share

What is the wattage of a typical halogen bulb?

Halogen lights come in a wide variety of aperture specifications, with sizes generally proportional to the light source power. The power typically ranges from 3-5W per bulb. LEDs are more energy-efficient: LEDs have high luminous efficiency, nearly twice that of fluorescent lamps. For the same daytime running lights, LED components consume only 1/20th the energy of halogen bulbs. The cost of LED components has also significantly decreased year by year, currently dropping at a rate of over 20% annually. LEDs offer excellent durability: LED components have a simple structure with excellent impact and shock resistance, making them less prone to breakage and highly adaptable to various environments.
11
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.