What brand of engine is Junma?

How to Calculate Power and Horsepower?

Conversion methods between power and horsepower: 1. Metric system: 1 horsepower = 735 watts = 0.735 kilowatts 1 kilowatt = 1.36 horsepower 2. Imperial system: 1 horsepower = 746 watts = 0.746 kilowatts 1 kilowatt = 1.34 horsepower The horsepower commonly referred to is the metric horsepower. Extended information: 1. Power: Power refers to the amount of work done by an object per unit time, that is, power is a physical quantity describing the speed of doing work. 2. Horsepower: Horsepower is a unit for measuring the performance of a car engine and an important parameter for evaluating the performance of a car. Simply put, the greater the horsepower, the more energy the engine can release in the same amount of time. 3. Effect: Both power and horsepower refer to the force generated by the engine, just expressed in different units. They are both numerical values used to measure how much energy an engine can produce.

2

4

Share

Is it necessary to replace brake pads at a 4S shop?

Replacing brake pads doesn't necessarily require going to a 4S shop; they can be replaced at auto repair shops. The thickness of new brake pads is approximately 13mm, and they gradually wear thinner with continuous friction during use. When the brake pad thickness is less than one-third of the original thickness, it's time to prepare for replacement. Pay attention to the small protrusions (about 3mm) at both ends of the brake pads - when they become flush with the pad surface, replacement is mandatory. Additionally, some vehicle models are equipped with brake pad sensors that will trigger a dashboard warning when the pads wear to a certain extent, indicating the need for replacement.

14

3

Share

Is there a specific installation direction for the brake booster pump check valve?

Automotive brake booster pump check valves do not have a specific installation direction; they can be installed directly as is: 1. The brake booster pump is a large-diameter vacuum chamber with a diaphragm (or piston) in the middle that has a push rod, dividing the chamber into two parts, one part connected to the atmosphere; 2. The other part is connected to the engine intake manifold via a pipe. Therefore, when the engine is turned off, there is no intake vacuum, and thus no power assistance, requiring much greater human effort for braking; 3. It is important to note that many beginners mistakenly believe that there is no braking when the engine is turned off, which is incorrect.

8

0

Share

What grade of gasoline should be used for the CT5?

Cadillac requires 95-octane gasoline. Methods to check the fuel tank capacity of a car: Refer to the owner's manual. The car manual can be considered a comprehensive guide, containing detailed information about the vehicle, including maintenance schedules and fuel tank capacity. Owners can use this information to determine how much fuel to add, and it is advisable not to exceed the safe capacity. Fuel tank capacity measurement unit: Internationally, the standard unit for measuring car fuel tank capacity is liters (L). Different countries also have their own standards for fuel tank capacity. In China, the regulation stipulates that the fuel tank capacity should be 95% of the rated value, but in practice, the actual capacity is often greater than the nominal capacity.

1

0

Share

Does the Thickness of Brake Pads Affect Braking?

When the thickness of the brake pads becomes very thin, the braking performance will significantly decrease, affecting driving safety. Generally, the thickness of new brake pads is about 1.5cm. When the brake pads wear down to only 0.5cm, you should increase the frequency of self-inspection. When the brake pads wear down to only 0.3cm, you must replace them promptly. This is the minimum replacement limit for brake pads. Don't delay, as it could lead to an accident at any moment. Additionally, each brake pad has a raised indicator on both sides, which is about 2-3mm thick. If the thickness of the brake pad has worn down to be level with this indicator, it must be replaced immediately. Some higher-end models will display a warning light on the dashboard when the brake pads are too thin, so owners should pay attention promptly.

13

3

Share

What is the function of a brake wheel cylinder?

The brake wheel cylinder is an indispensable component of the braking system. Its primary function is to push the brake shoes, which then rub against the brake drum to decelerate or stop the vehicle. When the brake pedal is pressed, the master cylinder generates thrust to force hydraulic fluid into the wheel cylinders. The pistons inside the wheel cylinders move under hydraulic pressure, pushing the brake shoes. The hydraulic brake system consists of a master cylinder and a brake fluid reservoir. One end connects to the brake pedal, while the other connects to the brake lines. The master cylinder contains brake fluid with inlet and outlet ports. When braking, the outlet port opens while the inlet port closes. Under the pressure of the master cylinder piston, brake fluid is forced through the lines to each wheel cylinder to perform braking. Upon releasing the brake pedal, the master cylinder's outlet port closes and the inlet port opens, allowing brake fluid to flow back from the wheel cylinders to the master cylinder, returning to the original state.

1

2

Share

What brand of engine is Junma?

How to Calculate Power and Horsepower?

Is it necessary to replace brake pads at a 4S shop?

Is there a specific installation direction for the brake booster pump check valve?

What grade of gasoline should be used for the CT5?

Does the Thickness of Brake Pads Affect Braking?

What is the function of a brake wheel cylinder?

Where is the Cabin Air Filter Located in the Changan Alsvin?

Which pipe should be blocked when the brake cylinder is leaking air?

The Difference Between Plug-in and Charging Models

Is There a Difference Between Front and Rear Brake Discs?