What brand is upala tire?

1 Answers
Freddie
07/30/25 2:09am
upala tire is called Yilian tire, which is relatively niche. Here is some relevant information about tires: Tire Introduction: Tires are the only part of a car that comes into contact with the ground. Some car owners only replace the tires on the drive wheels when changing tires. For example, some front-wheel-drive car owners only replace the two front tires, while some rear-wheel-drive car owners only replace the two rear tires. In fact, this practice is acceptable. Tire Aging: Tires are made of rubber and will age over time. It is recommended that car owners replace their tires every four years, even if the mileage is low during those four years. This is because tires can also age when left unused for long periods, so it's important to check the production date when purchasing tires.
Was this review help?
8
2
Share
More Forum Discussions

Do out-of-town vehicles need a Beijing entry permit when leaving Beijing?

Out-of-town license plates do not need a Beijing entry permit when leaving Beijing. However, a Beijing entry permit is required to enter within the Sixth Ring Road of Beijing. All non-local vehicles entering within the Sixth Ring Road of Beijing (excluding the Sixth Ring Road) or traveling in restricted areas of Changping, Huairou, and Yanqing County towns must apply for a Beijing entry permit. The following materials are required to apply for a Beijing entry permit: 1. The driver's ID card. 2. A valid motor vehicle driver's license. 3. The motor vehicle registration certificate. 4. A valid compulsory motor vehicle traffic accident liability insurance certificate. 5. A valid motor vehicle safety technical inspection qualification mark. 6. A certificate confirming the vehicle meets environmental protection requirements, as approved by the local environmental protection authority. Note: The validity period of the Beijing entry permit is 7 days and can be extended once.
9
3
Share

What lights should be used when passing through an arched bridge slope?

When passing through an arched bridge slope, you should use the high and low beams alternately. According to the Implementation Regulations of the Road Traffic Safety Law of the People's Republic of China, when a motor vehicle passes through sharp curves, slopes, arched bridges, crosswalks, or intersections without traffic signal control at night, it should alternately flash the high and low beams twice as a signal. When a motor vehicle approaches sections such as sharp curves or the top of slopes that affect safe sight distance, or when overtaking or encountering emergencies, it should slow down and sound the horn as a signal. The main challenge of driving at night is poor visibility, so lights must be used. Generally, low beams are sufficient for normal nighttime driving. Turn signals must be used when turning. If you encounter a poorly lit road with insufficient lighting ahead, you should switch to high beams.
16
1
Share

Why Does the Engine Temperature Drop While Driving?

Possible reasons include insufficient coolant, a damaged thermostat, a malfunctioning cooling fan, or a faulty water pump. Here are the methods to address the issue of dropping engine temperature: 1. Check the coolant level and whether it has deteriorated. If it is low, add an appropriate amount. If it has deteriorated, clean the water passages and replace the antifreeze. 2. Check the engine oil level. If the oil is too low, add or replace it. 3. Check if the radiator is blocked by foreign objects. If blocked, clean it thoroughly. 4. Check if the fan blades are deformed. Replace the fan or adjust the belt. 5. Check the water temperature sensor and its circuit for proper functioning. 6. Inspect the thermostat. Remove and inspect the thermostat, place it in hot water to observe if it opens properly. If it does not open normally, replace the thermostat.
20
0
Share

What causes the three warning lights for tire pressure, anti-skid, and ABS to illuminate in a Volkswagen?

This situation occurs due to abnormal tire pressure in the car tires, which causes encoding errors in the electronic control unit, resulting in a malfunction. You can use a diagnostic tool to read the fault codes or directly visit a 4S shop for professional repair. It is dangerous to continue driving under these circumstances. There are two scenarios when the steering wheel light, anti-skid light, and tire pressure monitoring light illuminate: 1. Low tire pressure: Insufficient tire pressure causes a difference in wheel speed, leading the system to interpret that some wheels are slipping, and the steering wheel is deviating, thus triggering these warning lights. 2. Dirty engine throttle: A dirty engine throttle results in a mismatch between the engine's power output and the vehicle transmission's torque, causing the system to report chassis fault codes. It is recommended to first balance the tire pressure at a tire shop and then inspect the throttle. If it is found to be dirty, clean it promptly.
15
3
Share

How to align the timing belt of Fiat Viaggio 1.4T?

Fiat Viaggio 1.4T timing belt alignment method: 1. Align the timing mark on the camshaft gear with the mark on the valve cover; 2. Align the timing mark on the crankshaft gear with the mark on the front cover (same procedure for both driving and driven pulleys); 3. Adjust the tensioner to tighten the belt. Taking the Viaggio 2017 1.4T Manual Enjoyment Edition as an example: This is a compact car launched by GAC Fiat, with dimensions of 4679mm in length, 1850mm in width, 1471mm in height, and a wheelbase of 2708mm. It is equipped with a 1.4T turbocharged engine and a 5-speed manual transmission.
2
5
Share

How long does it take to repaint a car?

Repainting a small car typically takes 1 day. The method for repainting a car is as follows: 1. Use clean water to wash the area where the paint has chipped; 2. Use sandpaper to smooth the chipped area and check by hand if the surface is even; 3. Cover the areas that do not need repainting with masking tape; 4. Use a spray paint can that matches the car's color and spray the chipped area. Methods to prevent paint chipping: 1. Avoid using hard objects or dry cloths to wipe the paint surface directly—rinse off dust and dirt with water first, then use a clean, absorbent cloth to wipe; 2. Avoid parking under direct sunlight for prolonged periods; 3. Reduce the frequency of car washes and avoid waxing or polishing; 4. Promptly remove corrosive substances to minimize paint corrosion.
7
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.