What brand is Torch spark plug?

1 Answers
DiAbel
07/30/25 6:47am
Torch spark plug is a product of the Torch brand, a domestic brand under Zhuzhou Torch Spark Plug Co., Ltd. Where is the spark plug located: The spark plug is installed on the side or top of the engine. In earlier models, spark plugs were connected to the distributor via ignition cables. Over the past decade, most car engines have been updated to connect the ignition coil directly to the spark plug. What are the effects of a faulty spark plug: If the spark plug is damaged, it can directly cause issues such as leakage in the vehicle's ignition system, increased fuel consumption, and reduced power. The most significant problem is difficulty in ignition, which affects the normal operation of the vehicle. Severe erosion of the spark plug, such as scarring at the top, damage, or melted and eroded electrodes, indicates that the spark plug is damaged and should be replaced. Steps to replace a spark plug: Open the hood and remove the engine's plastic cover. Disconnect the high-voltage ignition wires, marking each cylinder's position to avoid confusion. Use a spark plug socket to remove the spark plugs one by one, ensuring to check for and clean any external debris like leaves or dust. Insert the new spark plug into the spark plug hole, hand-tighten it a few turns, and then use the socket to tighten it further. Reinstall the high-voltage ignition wires in the correct firing order and reattach the cover.
Was this review help?
2
0
Share
More Forum Discussions

What Are the Reasons for a Car Seat Belt Getting Stuck?

The reasons for a car seat belt getting stuck are as follows: 1. The vehicle has been involved in a collision accident; 2. The seat belt is too dirty or dust has entered the hinge of the seat belt; 3. Foreign objects have entered the locking position of the seat belt. Relevant information about car seat belts is as follows: 1. Introduction: A car seat belt is a safety device designed to restrain occupants during a collision and prevent secondary collisions with the steering wheel, dashboard, etc., or to prevent occupants from being thrown out of the vehicle, which could lead to injuries or fatalities. 2. Working Principle: The retractor contains a ratchet mechanism. Under normal circumstances, occupants can pull the webbing freely and evenly on the seat. However, when the continuous pulling of the webbing from the retractor stops or when the vehicle encounters an emergency, the ratchet mechanism will lock, automatically preventing the webbing from being pulled out.
2
1
Share

Which Volkswagen model features a black emblem?

Volkswagen's model with a black emblem is the Taos. Here are the relevant details: 1. Taos exterior design: The diamond-pattern glossy black grille seamlessly integrates with the square-shaped LED headlights. Below, it adopts the same through-type air intake and spoiler design as the T-Roc R. The new two-tone five-spoke aluminum alloy wheels paired with red brake calipers, along with the red and black dual-tone body, emphasize a youthful and sporty appearance. 2. Taos powertrain: Equipped with the same 2.0T turbocharged engine as the T-Roc R, delivering a maximum power of 221 kW and a peak torque of 400 Nm. 3. Body dimensions: The Taos belongs to the Tiguan product line and, like the T-Roc, is positioned as a compact SUV. Its body dimensions are 4465 mm in length, 1842 mm in width, and 1636 mm in height, with a wheelbase of 2690 mm.
15
3
Share

What are the symptoms of a faulty motorcycle brake pump?

The symptoms of a faulty motorcycle brake pump are as follows: 1. Shaking when braking: This phenomenon mostly occurs in older motorcycles due to prolonged use and significant wear. It is recommended to consider using a lathe polishing process or replacing the brake pads (for older vehicles). 2. The direction tends to veer to one side: This is commonly known as 'brake pull,' and the main cause of this issue is uneven force applied by the left and right brake calipers on the brake pads. In this case, the caliper needs to be replaced. 3. Brake does not return: It is necessary to check if the brake fluid is insufficient; if there is oil leakage at the brake caliper, pipelines, or joints; or if the master cylinder or caliper components are damaged. 4. Reduced braking force: Possible causes include insufficient hydraulic pressure in the caliper or master cylinder, which may indicate oil leakage; brake system malfunction; or air leakage in the brake pipelines, requiring repair.
7
1
Share

What are the tips for using the Audi A4L auto start-stop function?

The following are tips for using the Audi A4L auto start-stop function: 1. The auto start-stop function can only be permanently disabled by coding, and it needs to be manually turned off by the driver each time during normal use. 2. During heavy traffic holidays, turning off this function can make driving more comfortable. The slow start-up might lead to frequent lane cutting by other drivers in congested areas. 3. Additionally, when starting on a slope, this function should also be turned off to avoid slow response and potential rolling back. Extended information: 1. The auto start-stop function shuts off the engine, and unless the vehicle is also equipped with an auto hold function, the brake pedal must be continuously pressed during this process. Releasing the brake pedal will immediately restart the engine. 2. In simple terms, the auto hold function automatically applies the brakes for the driver. Pressing the accelerator pedal again releases the wheels and starts the vehicle.
2
4
Share

What are the symptoms of a faulty motorcycle water temperature sensor?

Motorcycle water temperature sensor failure can cause the ECU to stop controlling the fuel injector, preventing the vehicle from starting when overheated. Below are the relevant details: 1. Resistance value of the water temperature sensor: For fuel-injected motorcycles, the water temperature sensor or engine temperature sensor typically has a resistance value of 2-3kΩ when the engine is cold and the ambient temperature is around 20℃. When the engine reaches 80℃, the sensor's resistance value should be between 200-400Ω. 2. Function of the temperature sensor: It continuously monitors the engine temperature and transmits this information to the ECU as an electrical signal. The ECU adjusts the fuel injection quantity (injection pulse width) based on changes in this signal. If the connection between the temperature sensor and the ECU is broken or short-circuited during signal transmission, most vehicle models' ECUs will automatically use a temperature map of either 80℃ or 100℃ to control fuel injection quantity and ignition timing. Air-cooled engines generally use 80℃, while water-cooled engines typically use 100℃.
7
1
Share

Where is the car jack located in the trunk?

Car jacks are generally placed underneath the spare tire in the trunk, with designated mounting positions. These are located along the protruding long edges on both sides of the vehicle's underbody, where there are several reinforced areas specifically designed for jack placement. Here's additional information: 1. Passenger cars: For family vehicles, the support points are typically on the inner side of the side skirts, approximately 20 cm behind the front wheels and 20 cm in front of the rear wheels, capable of withstanding relatively high pressure. Incorrect operation, such as placing the jack on chassis steel plates, bumpers, or crossbeams, may cause the side skirts to deform, resulting in unnecessary damage to the chassis. 2. Precautions: When using a jack, ensure the car is parked on a safe and level surface with the brakes engaged. Additionally, pay attention to the jack's maximum load capacity and never exceed it to prevent accidents due to insufficient support.
13
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.