What brand is the original engine oil of FAW-Volkswagen?

1 Answers
LunaLee
07/29/25 6:43pm
Volkswagen's original engine oil brands include Castrol, Shell, Valvoline, Mobil, and Great Wall, with Castrol being the most commonly used for various models. The related introduction is as follows: Castrol: Castrol Edge 5W30 fully synthetic oil is suitable for TSI-MPI-EA111-EA211 engines. Due to its lower viscosity compared to the white barrel, it is not suitable for EA888-G2 series engines. Volkswagen original engine oil grades: Volkswagen original engine oil is divided into three grades: mineral oil, synthetic oil, and fully synthetic oil. Different regions use different base oils; engine models and driving environments vary, leading to different oil choices. Fully synthetic oil, without blending with mineral oil, offers the best lubrication and cleaning effects for the engine, superior high and low-temperature performance, longer oil change intervals, and better environmental adaptability. For turbocharged models, it not only enhances power output but also reduces fuel consumption.
Was this review help?
13
1
Share
More Forum Discussions

What Problems Occur When There Is Air in the Car Radiator?

If air gets mixed into the car radiator, it can cause the vehicle's engine to overheat, and in severe cases, lead to "boiling over." At this point, the coolant must be replaced to expel the air. Below is more information about coolant: 1. Introduction: The full name of coolant should be antifreeze coolant, meaning it is a cooling liquid with antifreeze properties. Antifreeze prevents the coolant from freezing in cold winter conditions, which could otherwise crack the radiator or damage the engine cylinder block or head. 2. General Uses: It is used in the cooling systems of cars, diesel locomotives, tractors, ships, engines, radiators, and various mechanical equipment, including gasoline engines. It offers multiple functions such as antifreeze, anti-boil, anti-corrosion, and anti-scale.
14
1
Share

What Causes Car Shaking When Releasing the Clutch?

The main reasons for car shaking when releasing the clutch are as follows: 1. Uneven distribution of positive pressure between the driving and driven discs: The spring force of the frequently engaged clutch pressure springs is uneven, the adjustment of each release lever is inconsistent, and/or the fingers of the diaphragm spring are uneven, leading to unsynchronized pressure application times, uneven force on the pressure plate, and even tilting of the pressure plate, resulting in poor contact between the driving and driven discs and causing clutch shaking. 2. Weakening of damping spring force: The weakening of the torsion damping spring force in the clutch, the weakening of the clutch pressure spring force, and cracks in the diaphragm spring can all cause shaking when the clutch is engaged. The strategy to address this is to replace the springs. 3. Poor contact of the clutch lining: Poor contact of the clutch lining, surface hardening, or adhesion of sticky substances can easily cause clutch shaking. In this case, the clutch lining should be re-bonded.
12
2
Share

What is the problem when the clutch suddenly fails?

Sudden clutch failure is caused by damage to the clutch master cylinder or slave cylinder. Here are the specific details about the car clutch: 1. Cause of failure: It usually starts with excessive wear of the clutch disc and ends with engine idling and clutch damage. Therefore, in terms of response, the main focus is on judging the wear stage and damage degree to prevent further deterioration of the wear. 2. Maintenance: Reduce the frequency and duration of half-clutch operation. Unlike dual-clutch transmissions, manual transmissions allow full control over the frequency and duration of half-clutch operation, thereby reducing clutch wear. For dual-clutch transmissions, most wear occurs during low-speed driving. Therefore, mastering manual mode during low-speed stages can extend the service life of the clutch.
5
1
Share

What are the consequences of a car water pipe bursting?

After the water pipe bursts, the car cannot continue to drive. You must repair the pipe and add water or coolant before you can drive again. The following are the reasons for a water pipe burst: 1. Pipe aging: A sudden burst of the car water pipe is likely caused by poor quality or aging of the pipe. Simply replace it with a high-quality pipe. 2. Insufficient coolant in the radiator: The fan cannot fully open or is damaged and not working. 3. Dirty radiator exterior: Or severe internal scale buildup, leading to poor heat dissipation. The radiator needs to be cleaned or replaced. 4. Fan clutch engagement is too late: The cooling fan is not working, or the fan rotation resistance is too high.
10
1
Share

What is PP+ABS as an Automotive Material?

ABS plastic is a ternary copolymer composed of three monomers: acrylonitrile (A), butadiene (B), and styrene (S). PP material is a type of plastic, specifically a high-density linear polymer. Body materials significantly impact vehicle quality and safety. Below is a detailed introduction regarding automotive safety: 1. Overview: Automotive safety for vehicles is primarily divided into two major aspects: active safety and passive safety. Active safety focuses on enabling smooth and controlled operation of the vehicle. Whether it's braking and accelerating in a straight line or steering left and right, the vehicle should remain as stable as possible to avoid deviating from the intended path, without compromising the driver's visibility or comfort. 2. Others: Automotive safety technology covers an increasingly broad and detailed range of aspects, evolving towards integration, intelligence, systematization, and comprehensive involvement. Strictly controlling speed during nighttime driving is a fundamental measure to ensure safety.
19
4
Share

What is the difference between position lights and low beam headlights?

Position lights and low beam headlights are both used for nighttime illumination. Position lights, also known as marker lights or commonly referred to as small lights, serve as warning lights to alert other vehicles. On the other hand, low beam headlights are designed to provide good lighting for the driver. Their differences are as follows: 1. Position lights: Position lights are also called 'marker lights.' The term 'position' signifies a warning, while 'marker' represents the outline. Position lights are installed at the edges of the vehicle's outline, allowing other vehicles to clearly see the position and size of your vehicle, thereby preventing rear-end collisions or side swipes. 2. Low beam headlights: Low beam headlights typically have an illumination range within 50 meters, primarily aimed at clearly seeing the road ahead. They are usually turned on in areas with heavy traffic, as high beam headlights can cause glare to oncoming drivers.
13
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.