What brand is the FF91 car?

What is the fuel tank capacity of the Mazda6 in liters?

Mazda6 has a fuel tank capacity of 64 liters, which is the officially announced data. Owners who have purchased a Mazda6 can also check this information on the vehicle's configuration sheet. The Mazda6 uses 92-octane gasoline, with a fuel consumption of 7.8 to 8.2L per 100 kilometers. A full tank can cover a distance of approximately 780 to 820 kilometers. During daily driving, it is necessary to always pay attention to the remaining fuel level in the tank. This is usually observed through the fuel gauge inside the vehicle. If there are no other issues, the fuel level will be accurately reflected on the gauge. The fuel gauge typically has 5 to 6 segments, and it is advisable to refuel when there are about 2 segments left to avoid running out of fuel midway. During actual refueling, the amount of fuel may exceed the marked capacity. This is because the fuel tank capacity specified by the manufacturer is measured from the bottom of the tank to the safe fill level, and there is additional space from the safe fill level to the tank opening. This space is designed to accommodate fuel expansion due to temperature increases, preventing overflow. If fuel is filled up to the tank opening during refueling, the actual amount of fuel added may exceed the marked tank capacity.

14

4

Share

What is the valve adjustment size for Renault engines?

In most cases, the intake valve should be adjusted to 0.3mm, and the exhaust valve to 0.4mm. There are two common methods for checking and adjusting valve clearance: 1. Cylinder-by-cylinder adjustment method: Based on the firing order of the cylinders, once the piston of a specific cylinder is at the top dead center of the compression stroke, the intake and exhaust valve clearances of that cylinder can be adjusted. After adjustment, rotate the crankshaft and follow this method to adjust the valve clearances of the other cylinders step by step. 2. Two-step adjustment method: (1) Rotate the crankshaft to position the first cylinder's piston at the top dead center of the compression stroke, aligning the flywheel mark with the inspection hole line. At this point, valves 1, 2, 4, 5, 8, and 9 can be adjusted (referring to the engine valve arrangement from front to back). (2) Rotate the crankshaft one full turn to position the sixth cylinder's piston at the top dead center of the compression stroke, then adjust valves 3, 6, 7, 10, and the "additional two" (i.e., 11 and 12). (3) During adjustment, turn the adjusting screw while inserting a feeler gauge between the valve stem end and the rocker arm, moving it back and forth until a slight resistance is felt.

11

5

Share

How to Determine the Production Date from Car Glass?

The method to determine the production date from car glass is as follows: It is represented in the form of numbers plus dots. The dots can be either in front of or behind the numbers. The way to read this representation is simple: the number indicates the year, and the dots indicate the month. If the dots are in front of the number, it represents the first half of the year. Subtract the number of dots in front of the number from 7 to get the month in the first half of the year. If the dots are behind the number, it represents the second half of the year. Subtract the number of dots behind the number from 13 to get the month in the second half of the year. Another representation is numbers plus small dots plus large dots. Here, the number represents the year, the small dots represent the quarter (there are 4 quarters in a year, so there are usually 4 small dots), and the large dots represent the month within the quarter (a quarter has 3 months, so there are usually 3 large dots). Car glass is manufactured by heating the glass in a furnace to near its softening temperature, then quickly transferring it to cooling grids with different cooling intensities for uneven cooling. This creates different stress levels between the main viewing area and the peripheral areas of the glass. Generally, this type of production results in regional tempered glass.

10

4

Share

Is the Weilan's engine a three-cylinder or four-cylinder?

The all-new Buick Weilan is equipped exclusively with three-cylinder engines. Below are details about the Buick Weilan: 1. The Weilan 20T model features the eighth-generation Ecotec 1.3T direct-injection turbocharged engine, paired with a new CVT intelligent continuously variable transmission, delivering a maximum power of 121kW at 5600rpm and a peak torque of 240Nm between 1500-4000rpm. Compared to the current Weilan 20T's 1.5T powertrain, this configuration significantly improves acceleration response and smoothness across all speed ranges, while reducing combined fuel consumption to just 5.5L per 100km, approximately 5.2% lower than the previous generation. 2. The Weilan 15T variant utilizes the eighth-generation Ecotec 1.0T turbocharged engine mated to a 6-speed DSS intelligent transmission, producing 92kW at 5800rpm and 180Nm between 1350-4500rpm. With peak torque available as low as 1350rpm, the 15T demonstrates agile low-speed performance ideal for urban stop-and-go traffic, achieving a remarkable 14.8% reduction in fuel consumption (5.2L/100km combined) versus its predecessor for substantially enhanced fuel efficiency.

17

1

Share

How to Set the Time on a Ford Focus?

Ford Focus time setting steps are as follows: 1. Turn on the ignition switch to display the time on the instrument panel. 2. Press and hold the protruding button in the middle of the instrument panel for 3 seconds, and the clock on the panel will start flashing. 3. Press the button up or down to adjust the hour according to actual needs. 4. Continue pressing the button to adjust the minutes to the correct value. 5. After both hour and minute are set correctly, wait for 5 seconds to complete the adjustment. Below are detailed specifications of the Ford Focus: 1. Engine: The Focus is equipped with a Duratec-HE reverse-mounted aluminum alloy engine, cast entirely in aluminum with reverse-mounted design. It delivers a maximum power of 104kW and maximum torque of 180N·m (2.0L engine). Combined with the Variable Intake System (VIS), plastic-steel equal-length intake manifold, it demonstrates advantages of agile acceleration, smooth operation, efficient air intake, as well as low noise and fuel consumption. 2. Transmission: The Focus features a Sequential Port Shift (SPS) manual-automatic transmission. Through advanced ESSC electronic synchronous shift control system, it achieves fast and precise gear shifting while balancing the exhilarating acceleration of manual transmission and the convenient comfort of automatic transmission. 3. Suspension System: The Focus rear suspension adopts SLA Control Blade fully independent suspension system, maintaining maximum tire contact with the road for smooth cornering performance. Paired with double ball joints, it effectively eliminates vibration noise from tires. The high-rigidity rear subframe and rear anti-roll bar deliver stable, solid and comfortable dynamic performance. Combined with 265mm rear solid disc brakes, it provides sharp and precise four-wheel braking force.

12

5

Share

How to Close the Windows After Turning Off the 10th-Generation Civic?

To close the windows after turning off the 10th-generation Civic, follow these steps: 1. Use the remote control to close the windows. First, press the unlock button on the key. 2. Release the button, then press and hold the unlock button for 5 seconds to automatically lower the windows. 3. After turning off the 10th-generation Civic, press and hold the lock button on the car key to close the windows. The car key can be used to adjust the automatic window operation, which is a hidden feature. 4. To close the windows using the remote control after turning off the 10th-generation Civic, press the unlock button once, release it, and then press and hold the unlock button for 5 seconds to automatically lower the windows. Here are some details about the 10th-generation Civic: 1. The body dimensions of the 10th-generation Civic are 4649*1800*1416 mm. Its exterior design follows the overseas model, featuring full LED headlights. The side profile of the car is more daring than the front, with "bracket-style" LED taillights and a dart-shaped light cluster. 2. The interior continues the style of previous models, using soft materials and accented with silver or metal decorative elements, along with a full-color LCD instrument panel. 3. In terms of features, the new Civic comes standard with a multifunction steering wheel, a 7-inch DA screen, a full LCD instrument panel, automatic dual-zone climate control, cabin air conditioning, a power sunroof, rear parking sensors, and a rearview camera. 4. Safety features include standard front and side airbags, tire pressure monitoring, keyless entry, push-button start, VSA stability control, EBD electronic brake-force distribution, HAS hill-start assist, and emergency braking alerts.

2

5

Share

What brand is the FF91 car?

What is the fuel tank capacity of the Mazda6 in liters?

What is the valve adjustment size for Renault engines?

How to Determine the Production Date from Car Glass?

Is the Weilan's engine a three-cylinder or four-cylinder?

How to Set the Time on a Ford Focus?

How to Close the Windows After Turning Off the 10th-Generation Civic?

Does the Audi R8 have a convertible version?

How to Solve the Rattling Noise from Camry's Sunroof?

Where is the Odyssey fuel filter located?

What is the reason why AWD (All-Wheel Drive) cannot be towed?