What brand is SMRT semi-thermal melt tire?

What Causes a Car Not to Start?

Analysis of car starting failure is as follows: 1. Electrical or electronic failure: The phenomenon occurs very suddenly without any warning. Electrical failures include: blown fuse, open circuit in the high-voltage coil, open circuit in the low-voltage circuit, detached central ignition wire, leaking distributor rotor, or damaged spark plugs. Electronic failure mainly refers to the malfunction of the central computer control board. 2. Fuel system failure: Stalling caused by fuel system issues often comes with symptoms like weak engine power or a spongy accelerator pedal. Possible fuel system problems include: fuel pump failure, blocked fuel lines, clogged fuel filter, carbon buildup on spark plugs, or damaged fuel injectors. Sometimes, the fuel tank might be empty without the owner's knowledge. 3. Mechanical failure: Common mechanical failures include: timing belt breakage, cylinder leakage causing no pressure, etc.

10

0

Share

Where is the cigarette lighter in the 2021 Corolla?

The cigarette lighter socket in the Toyota Corolla is located inside the front armrest box. The cigarette lighter is a component found in all cars, designed to provide a convenient ignition source for drivers who smoke. Commonly referred to as cigarette lighters, they can be divided into those that draw power from the vehicle's electrical system. Some manufacturers produce cigarette lighters not for lighting cigarettes but for drawing power from the car. Below are common mistakes when using a cigarette lighter: 1. Not unplugging external devices when starting the vehicle: During startup, external devices connected to the cigarette lighter are prone to burnout due to the high current surge, especially MP3 players and USB drives. Therefore, it's advisable to unplug them before starting the car and plug them back in after the engine is running; 2. Not unplugging external devices when turning off the engine: Depending on the vehicle's settings, some cigarette lighter sockets remain powered even after the engine is turned off. Leaving external devices plugged in can lead to unnecessary battery drain; 3. Wiggling during plugging and unplugging: Excessive movement can deform the curved spring contacts of the device's plug, leading to poor contact and intermittent connectivity; 4. Frequently bumping the cigarette lighter plug while operating the vehicle, causing it to become loose.

19

5

Share

Is the windshield film applied on the outside or inside?

The windshield film needs to be applied on the inside of the car. Here is an introduction to the functions of car window film: 1. UV protection: The windshield has a large heating area and receives the most UV radiation. Applying film can effectively block UV rays, protecting the health of the driver and passengers. 2. Heat insulation: Windshield film can block a portion of heat. 3. Anti-glare: During the day, sunlight can be dazzling and cause glare. Applying film to the windshield can effectively reduce blinding glare. 4. Explosion-proof: Since car windshields are made of tempered safety glass, if the glass shatters, the film prevents fragments from flying, thereby protecting the driver's safety.

20

2

Share

What are the requirements for an A2 driver's license?

A2 driver's license application requirements are as follows: 1. An A2 driver's license cannot be obtained initially; it can only be acquired through an upgrade. The driver must have held a (B1) medium-sized bus or (B2) large truck driving qualification for more than three years, with no full-point record in the two most recent scoring cycles before application; or have held an (A1) large passenger vehicle driving qualification for more than one year, with no full-point record in the most recent scoring cycle before application. 2. Drivers aged between 24 and 50 years old must present their ID card, health certificate, and B driver's license at the vehicle management office in the region where the B driver's license was issued to apply for an upgrade to an A2 driver's license.

12

5

Share

What does gear oil 85w140 mean?

Automotive gear oil 85w-140 indicates that the gear oil is a multi-grade oil, with two grades of 85W and 140, suitable for ambient temperatures ranging from -26 to +50. The relevant introduction is as follows: 1. The SAE viscosity classification divides gear oil into grades such as 75W, 80W, 85W, 90, 140, and 250. 2. Gear oil is a high-viscosity lubricant specifically designed to protect transmission power components, typically accompanied by a strong sulfur odor. Vehicle gear oil is classified by performance and viscosity. Currently, the American Petroleum Institute (API) performance classification and U.S. military gear oil specifications are widely adopted worldwide. Most manual transmission lubricants and differentials use hypoid gear oil. These contain extreme pressure (EP) additives and anti-wear additives to handle the action of hypoid bevel gears.

17

2

Share

How to Use a Manual Jack?

Here are the specific steps for using a manual jack: 1. Place a non-slip pad (such as a rubber mat) under the base of the jack, then position the jack under the vehicle for lifting. 2. When the top of the jack contacts the chassis, ensure it is properly supported and lift the vehicle until the wheels are off the ground. 3. Using a jack is very simple, but always remember to keep it level, stable, and slow during operation. It is strongly emphasized never to crawl under the vehicle while using a car jack, as it poses significant risks. Below is some relevant information about jacks: 1. A jack is a compact lifting device that uses a rigid lifting component as its working mechanism to elevate heavy objects within its stroke range via a top saddle or bottom claw. 2. Car jacks can be categorized into four types: rack jacks, screw jacks, hydraulic jacks, and pneumatic jacks. A rack jack consists of a rack, gear, and handle, and operates by turning the handle to raise or lower the rack. 3. Hydraulic jacks are further divided into general-purpose and specialized hydraulic jacks, with a relatively complex working principle. Their advantages include faster lifting speeds and greater load-bearing capacity compared to rack jacks. Screw jacks rely on thread self-locking to support heavy loads and have a simple structure with high weight capacity. However, their efficiency is lower, with slow lifting and fast lowering speeds. Pneumatic jacks are less common and operate by inflating with vehicle exhaust, making them relatively unknown due to their unique usage conditions.

1

2

Share

What brand is SMRT semi-thermal melt tire?

What Causes a Car Not to Start?

Where is the cigarette lighter in the 2021 Corolla?

Is the windshield film applied on the outside or inside?

What are the requirements for an A2 driver's license?

What does gear oil 85w140 mean?

How to Use a Manual Jack?

What does the ECO indicator on a car dashboard mean?

Is driving on highways more fuel-efficient than driving in urban areas?

Where is the Subframe Located?

What is the appropriate idle speed?