What brand is kapsen tires?

2 Answers
DeJudah
07/24/25 4:41pm
kapsen is a tire brand under Hongsheng Rubber Group, mainly producing load-bearing tires, engineering tires, motorcycle tires, and agricultural tires. Tires are usually made of wear-resistant rubber materials and can be divided into solid tires and pneumatic tires, with pneumatic tires consisting of an inner tube and an outer tube. Typically, manufacturers set the service life of tires at 3 years. If a vehicle drives 20,000 kilometers a year, it may be time to consider replacing them after 2 to 3 years. Methods for tire maintenance include: 1. Conducting a monthly inspection of the tires; 2. Replacing tires when they wear down to the indicator mark; 3. Regularly checking wheel alignment and balance; 4. Paying special attention to ensuring that tires on the same axle are uniform in specifications, structure, brand, and tread pattern when replacing tires.
Was this review help?
1
4
Share
DeAshley
08/11/25 9:13am
I have some knowledge about Kapsen tires. It's a brand specializing in automotive tires with good cost-performance. I've used them a few times myself, like when I changed a set for a long trip, and found the grip quite good, especially stable on wet roads without slipping. The price is much cheaper than Michelin or Goodyear, suitable for budget-conscious car owners. However, remember to regularly check tire wear as long-term use may increase noise, so it's recommended to service them every six months for safety. Overall, it's a practical choice with decent fuel efficiency, but don't expect outstanding performance in extreme conditions. If you prioritize comfort and smooth driving, you might consider trying them.
Was this review help?
17
4
Share
Expand All
More Forum Discussions

How often should the timing belt be replaced on a Volkswagen?

The timing belt generally needs to be replaced every 60,000 to 80,000 kilometers. It is recommended to refer to the vehicle's maintenance manual for the exact replacement interval. Below is relevant information about the vehicle timing belt: 1. Introduction: The timing belt is crucial for the proper functioning of the engine. If the timing belt fails, the valves and ignition system will stop working, and in severe cases, the cylinder head may also be damaged. As the engine operating hours increase, the timing belt and its related components, such as the timing belt tensioner pulley, timing belt tensioner, and water pump, will wear out or age. Therefore, it is important to thoroughly inspect these components for any issues each time the belt is replaced. 2. Precautions: During use, regularly check the condition of the timing belt. If cracks are observed on the surface of the timing belt, it may indicate aging. If unusual noises are heard while driving, check whether the timing belt is installed correctly.
4
2
Share

Are both left and right reverse parking tested?

Subject 2 reverse parking tests both left and right reverse parking. During the Subject 2 reverse parking test, stopping midway is not allowed. Below are the detailed explanations: 1. Regulations: If the vehicle stops for more than 2 seconds midway, 5 points will be deducted each time. Midway stopping refers to the vehicle having no displacement change within 2 seconds, which the system will judge as a midway stop. 2. Subject 2: Subject 2, also known as the small road test, is part of the motor vehicle driver's license assessment and is the abbreviation for the field driving skill test. For small vehicles C1 and C2, the test items include reverse parking, parallel parking, stopping and starting on a slope, right-angle turns, and curve driving (commonly known as S-turns) as the five mandatory test items (some regions also include a sixth item, high-speed card collection).
20
4
Share

What are the correct meshing conditions for helical gears?

Helical cylindrical gears must meet the following meshing conditions: equal normal module, equal tooth profile angle, equal helix angle, and opposite helix directions. Here are some related extensions: Correct meshing conditions for a pair of gears in transmission: The modules of the two gears must be identical. The tooth profile angles (pressure angles) of the two gears must be equal. The addendum coefficients of both gears must be equal. The meshing center distance (a) between the gears must be within the required assembly tolerance range. Correct meshing conditions for other types of gear transmissions: Meshing conditions for spur cylindrical gears: The modules of both gears must be equal, and the tooth profile angles on the pitch circles must be equal. Meshing conditions for straight bevel gears: The modules at the large ends and the tooth profile angles of both gears must be equal respectively.
4
0
Share

Why won't the motorcycle move after starting?

Motorcycle starts but won't move due to automatic centrifugal clutch failure, drive belt breakage, or spark plug burnout. Below are specific explanations: Automatic centrifugal clutch failure: Improper clutch operation causes it to get stuck without returning to position, resulting in the motorcycle starting but unable to accelerate or move. A faulty automatic centrifugal clutch requires replacement or repair. Drive belt breakage: Usually caused by pulley or belt malfunction. The rear transmission system needs to be disassembled for inspection. If the belt is broken or has significant gaps, it must be replaced. Spark plug burnout: Water ingress or blockage in the carburetor leads to spark plug burnout. Check if the fuel line is clogged. Loosen the bottom screw of the carburetor to let gasoline flow for a while before tightening it. If dirt enters the carburetor, inspect the spark plug. The carburetor needs cleaning or replacement after prolonged use, and a burnt spark plug must be replaced.
3
0
Share

What is the reason for the continuous flashing of the motorcycle ABS light?

The reasons for the continuous flashing of the motorcycle ABS light: Improper adjustment of the brake light switch; Poor internal contact of the brake light. How to handle it: Start the engine, press the brake pedal, use your fingers to push the brake switch linkage all the way down, then release the brake pedal to complete the self-setting position. Replace the brake light switch. If the ABS warning light is on, it is recommended not to continue driving. Because the ABS light indicates a fault in the vehicle's anti-lock braking system. During emergency braking, if the wheels lock up, the vehicle may lose control and skid, making it difficult for the driver to slow down or adjust the vehicle's trajectory, posing significant safety risks. The role of ABS: Maximize the effectiveness of the brakes, reducing braking time and distance. It can effectively prevent vehicle skidding and fishtailing during emergency braking, ensuring good driving stability. It allows steering during emergency braking, providing good steering control. It avoids severe friction between the tires and the ground, reducing tire wear.
13
4
Share

Can I change lanes to go straight when I find an accident while turning right?

In this situation, you can change lanes. There are regulations stating that if there is an accident ahead in your lane or temporary obstruction, you are allowed to change lanes. Precautions for changing lanes: When merging from an acceleration lane into a travel lane, observe the traffic conditions in the travel lane. When traffic is sparse, merge into the travel lane from behind normally moving vehicles. If a normally moving vehicle is following closely, control your speed and merge into the travel lane only after all vehicles have passed. Do not abruptly cut in between vehicles. You must signal in advance when changing lanes. When turning left, changing lanes to the left, preparing to overtake, leaving a parking spot, or making a U-turn, activate the left turn signal in advance. When turning right, changing lanes to the right, returning to the original lane after overtaking, or pulling over to the roadside, activate the right turn signal in advance. Penalties for illegal lane changes: Driving a motor vehicle on a highway or urban expressway without following the designated lane will result in 3 demerit points. When encountering queued or slow-moving vehicles ahead, overtaking by borrowing the opposite lane or cutting into the queue will result in 2 demerit points.
17
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.