What brand is Junma?

Where is the Rear Windshield Wiper Switch Located?

The rear windshield wiper switch is located on the control lever on either side of the steering wheel. Some models have it on a separate lever, while others combine it with the front wiper controls. The position varies depending on the vehicle model. To activate the rear wiper, simply push or pull the wiper lever forward or backward. The rear wiper is designed for the rear windshield and is commonly equipped on SUVs, MPVs, hatchbacks, and some liftback vehicles. Sedans, however, have a more steeply inclined rear windshield, whereas hatchbacks have a gentler slope. Front wipers are shielded by the engine hood, which blocks high-speed airflow from affecting their operation. In contrast, rear wipers are exposed, so their installation must account for the impact of high-speed airflow. Due to the inclined rear window of sedans, the high-speed airflow during driving not only creates drag but also significantly reduces wiper efficiency.

11

1

Share

What Emission Standard Does National V Represent?

"National V" represents the fifth category of emission standards. The symbol "V" is a Roman numeral, which is the earliest form of numerical representation, originating in Rome over 2000 years before Arabic numerals. For example, Roman numerals: Ⅰ, Ⅱ, Ⅲ, Ⅳ, Ⅴ correspond to Arabic numerals 1, 2, 3, 4, 5 respectively. Below is additional information on National V: 1. The National V standard is equivalent to the Euro 5 standard in the European Union, which has been implemented since 2009. It imposes stricter limits on vehicle emissions such as nitrogen oxides, hydrocarbons, carbon monoxide, and particulate matter. Each upgrade from National I to National IV reduces vehicle pollution by 30% to 50%. After review by relevant authorities, the National V standard was implemented nationwide starting from January 1, 2017. 2. The use of new standard gasoline and diesel will reduce multiple pollutants, cutting PM2.5 emissions from National IV to National V. Environmental indicators have been further tightened, with sulfur content reduced from 50ppm to 10ppm, and fuel quality significantly improved. The draft also revised gasoline grades from 90, 93, 97 to 89, 92, 95.

5

1

Share

Where is the water temperature gauge located on the dashboard of the Volkswagen Lavida?

The water temperature gauge is not displayed on the dashboard of the Volkswagen Lavida, but some facelifted models allow the water temperature gauge to be accessed on the instrument panel by pressing the button at the end of the windshield wiper stalk. If the water temperature gauge cannot be accessed, it is not a problem, as the water temperature sensor continuously monitors the coolant temperature. If the temperature rises, an automatic warning will be triggered, and the water temperature warning light will appear on the instrument panel. Below is more information about the water temperature gauge: 1. The normal operating temperature for a car's water temperature gauge is between 80~100°C, with minor variations depending on the engine's working conditions and the season. The normal temperature typically stays around 90°C. 2. The water temperature gauge usually displays two letters, C and H (or uses white and red zones to indicate temperature ranges). C stands for "Cold," while H stands for "Hot." If the water temperature gauge approaches the H mark or the red danger zone, and in severe cases, the water temperature warning light illuminates, it indicates that the engine coolant temperature is too high.

7

4

Share

What Causes Abnormal Noises from the Wheels?

Wheels can produce the following three types of abnormal noises: 1. Clicking sound: This occurs when the tire is punctured by a nail or has a small stone stuck in it. The noise happens once per wheel rotation, resembling something "clicking" or "tapping" against the ground, with the rhythm speeding up as the vehicle accelerates. If it's a stone, simply removing it will suffice. If it's a nail, and the tire pressure is still acceptable, you can drive directly to a repair shop to fix the puncture. 2. Groaning sound: This is caused by uneven tire tread, giving the sensation that the tire is constantly running over something, producing a "groaning" or "rumbling" noise, often accompanied by steering wheel vibration and a tendency to veer left or right. In such cases, it's best to replace the tire (or rim) and avoid driving with the issue. 3. Overinflated tire noise: This results in increased tire noise. For most passenger cars, the recommended tire pressure is around 2.4 bar when unloaded (both front and rear) and around 2.6 bar for the front and 2.7 bar for the rear when fully loaded. Each vehicle may differ, so refer to the owner's manual for exact values. Overinflated tires not only produce loud noise but also make the suspension feel stiffer, leading to a bumpy ride and lighter, less stable steering. In such cases, simply release some air to adjust the pressure to the standard value.

14

1

Share

Can Vehicle Inspection Be Conducted in Another Location?

Except for large passenger buses and school buses which cannot undergo inspection in another location, all other vehicles can be inspected in a different location. Currently, the traffic management authorities have fully implemented cross-provincial inspection for small cars, trucks, and medium-sized buses. Applicants can directly conduct inspections in provinces other than where the vehicle is registered and obtain the inspection compliance mark without needing to go through the delegated inspection procedure. Large passenger buses and school buses cannot be inspected in another location and must return to the vehicle's registration location for inspection. Vehicle inspection time requirements: Small and micro non-operational passenger vehicles are exempt from inspection for the first 6 years. After 6 years but less than 10 years, inspection is required every two years; after 10 years but less than 15 years, annual inspection is required; after 15 years, inspection is required every 6 months. Operational passenger vehicles require annual inspection within the first 5 years; after 5 years, inspection is required every 6 months. Trucks and large and medium non-operational passenger vehicles require annual inspection within the first 10 years; after 10 years, inspection is required every 6 months. Imported vehicles, like other vehicle types, can undergo regular inspection at any inspection station. Notes for vehicle inspection: Vehicles that fail inspection must be repaired within a specified time limit. If they still fail after the deadline, the vehicle management office will confiscate their license plates and prohibit further driving. Vehicles that do not undergo inspection without reason or fail inspection are not allowed to drive on the road or transfer registration. Vehicles that meet the scrapping conditions or exceed the specified service life will not be inspected, and their license plates will be revoked, their files canceled, and they will be scrapped.

13

2

Share

How to reset the tire pressure light on Geely GS?

Press the MENU button on the turn signal lever, select the tire pressure display option in the mileage and fuel information menu, and then press the SET/CLR button. The vehicle's instrument display will show a tire pressure relearning interface. After selecting "Yes," the tire pressure light will disappear. Here are the detailed steps: 1. Press the "MENU" button on the turn signal lever, select the "tire pressure display" option in the "mileage and fuel information menu," then press the Set/Clr button. The driver information center will display "Tire Pressure Relearn," select "Yes," and press the Set/Clr button. The horn will sound twice, and the driver information center will display "Tire Pressure Learning Enabled." At this point, the left front turn signal will stay on. Increase (or decrease) the left front tire pressure by 8.3 Kpa, and once the horn sounds, stop the pressurization (or depressurization) operation. 2. Next, the "right front turn signal will stay on," followed by the right rear and left rear turn signals in sequence. Repeat the pressurization or depressurization operation for the remaining three tires. After all four tires have been operated, the turn signals will stay on for 3 seconds, and the horn will sound twice, indicating the completion of tire pressure learning. Adjust the tire pressure to the desired value. The tire pressure displayed on the information center is the actual tire pressure. If unsure, you can measure it with a tire pressure gauge. If the error is not significant, the process is complete.

19

3

Share

What brand is Junma?

Where is the Rear Windshield Wiper Switch Located?

What Emission Standard Does National V Represent?

Where is the water temperature gauge located on the dashboard of the Volkswagen Lavida?

What Causes Abnormal Noises from the Wheels?

Can Vehicle Inspection Be Conducted in Another Location?

How to reset the tire pressure light on Geely GS?

How to Close Windows with the Key for URV?

How Often Should a Major Car Service Be Performed?

What are the steps to replace the key battery of the Baojun 510?

How to Solve Negative Pressure in a Car Fuel Tank?