What brand is decibel tire?

How to solve the abnormal noise of Roewe RX5 sunroof on bumpy roads?

To address the abnormal noise from the Roewe RX5 sunroof on bumpy roads, first identify the cause of the noise. If the sealing ring is aged, it needs to be replaced with a new one. If the screws are loose, tightening them can resolve the issue. Here are the specific methods: 1. Turn on the vehicle's ignition, press the sunroof switch button, and ensure the interior and exterior are quiet. Observe the sunroof's movement path to check for obvious up-and-down fluctuations. If present, it indicates component aging, and the parts must be replaced. 2. Loose screws can cause roof and sunroof noises and even pose a risk of the sunroof falling off. The solution is simple: locate the sunroof screws and tighten them. 3. Due to prolonged use, debris particles may accumulate on the sliding tracks. When the sunroof moves along these tracks, it can rub against the debris, causing abnormal noise. Therefore, it is essential to keep the tracks clean. Apply lubricant to both sides of the sunroof tracks, paying extra attention to areas where noise was previously detected, as these spots experience the most friction.

1

3

Share

How to Set Cruise Control in a Vehicle?

After the system is activated and the vehicle reaches the desired speed, press button B (SET) to maintain the vehicle at that speed continuously. Once the cruising speed is set, you can still accelerate using the throttle pedal as usual. When the throttle pedal is released, the system will restore the vehicle speed to the set cruising speed. Here is some related information about cruise control: The cruise control system reads the pulse signal from the speed sensor and compares it with the set speed, then issues commands to the servo mechanism to adjust the throttle opening, either increasing or decreasing it, to keep the vehicle at the set speed.

17

2

Share

What to Do When the Smart Key is Not Detected?

There are generally four situations when the car cannot detect the smart key: 1. The key's transmitter is damaged. 2. The car's receiver is damaged. 3. The door lock is damaged. 4. The battery in the key is dead. All the above issues can be checked and resolved at a regular repair station. Generally, there are two types of keys with sensing functions: 1. Conventional folding mechanical keys. 2. Hidden mechanical keys. If it is a conventional folding key, you can directly use the mechanical key to open the door when the battery is dead. If it is a hidden type, we need to find the mechanical key. Usually, the spare mechanical key is hidden inside the main key, which is not visible under normal circumstances. When needed, it can be pulled out and used as a conventional mechanical key.

2

1

Share

Where is the sunroof switch for the BMW 320i located?

The sunroof switch for the BMW 320i is located on the ceiling reading light area above the front seats. Here is additional information about the BMW 320i sunroof switch: 1. Automatic operation: Open: Pull the switch backward firmly. Close: Push the switch forward to close the sunroof. 2. Manual operation: Open: Gently pull the switch backward and hold it until the sunroof reaches the desired position. Close: Push the switch forward before reaching the desired position. 3. Panoramic sunroof glass lift: Press the center of the panoramic sunroof glass switch. The sunshade will automatically open, and the panoramic sunroof glass will begin to rise. Close: Push the button forward.

14

1

Share

How to Measure the Throttle Position Sensor?

Here are the methods for measuring the throttle position sensor: 1. Unplug the connector from the throttle position sensor and turn on the ignition switch. 2. Measure the voltage between Vcc and the idle contact, as well as between Vcc and the wide-open throttle contact; the readings should be 4.5-5.5V. 3. If the readings do not meet the requirements, check the ECU connection circuit. If the voltage values are correct, inspect the throttle potentiometer resistance. 4. Unplug the throttle potentiometer connector and measure the resistance between Vcc and the idle contact; it should be 1.5-2.6kΩ. 5. Measure the resistance between Vcc and VTH; at idle, it should be 0.75-1.3KΩ.

11

1

Share

Should the car door be replaced if it is dented?

Whether a dented car door needs to be replaced depends on the severity of the dent. If the dent is minor, it can be resolved through metal sheet repair. If the dent is severe, the door may need to be replaced. After a car door is dented, it should be addressed promptly to prevent rusting. Methods for maintaining the car body are as follows: 1. Waxing: Prevents the paint from coming into contact with air, slowing down the oxidation process. 2. Polishing: Removes the aged paint film, allowing the new paint film to restore its shine. 3. Glazing: Enhances the gloss and hardness of the car surface, effectively reducing scratches. 4. Coating: Reduces damage to the car paint from external environmental factors, ensuring the gloss of the paint surface does not diminish and extending the lifespan of the car paint.

12

0

Share

What brand is decibel tire?

How to solve the abnormal noise of Roewe RX5 sunroof on bumpy roads?

How to Set Cruise Control in a Vehicle?

What to Do When the Smart Key is Not Detected?

Where is the sunroof switch for the BMW 320i located?

How to Measure the Throttle Position Sensor?

Should the car door be replaced if it is dented?

How Many Kilometers Should Brake Fluid Be Replaced After?

How to Replace the Cabin Air Filter in a 2014 Volkswagen Sagitar?

What are the test items for the C2 license subject 2 exam?

Can Vehicles Undergo Annual Inspection in Another Location?