What brand is Britax?

What does practicing laps mean in driving training?

Practicing laps in driving training refers to the complete practice of various maneuvers during the learning of Subject 2, such as hill starts, reversing into a parking space, parallel parking, right-angle turns, and curve driving. One complete practice session is considered as running one lap, which serves as a simulation test method for learners. Additional information: Key points to note for Subject 2: 1. Reversing into a parking space: Main points for deduction include hitting the line while reversing, the car not entering the parking space, exceeding the time limit, and not following the designated route. 2. Parallel parking: Main points for deduction involve turn signals, maintaining a 30cm distance from the edge, and hitting the line. When entering the test area, turn right in advance and observe the highest point of the wiper aligning with the roadside line to adjust the 30cm distance. During reversing, remember the first right full turn, straightening, left full turn, parking in the space, turning on the left turn signal, and observing the rearview mirror when exiting to prevent the wheels from hitting the line. 3. Right-angle turns: Points for deduction include turn signals and hitting the line. After entering the test area, turn on the turn signal, and turn it off after the voice prompt. Incorrect operation of the turn signal results in a 10-point deduction. After entering the right-angle turn, adjust the car to maintain a 30cm distance from the edge line, similar to parallel parking. When making a full turn, slightly release the clutch to prevent stalling or stopping midway. Straighten the car after the rear wheels exit to prevent the wheels from hitting the line. 4. Curve driving: Main points for deduction involve the wheels hitting the line. During the test, focus on the front part, sit upright, align the left window corner with the inner side of the left yellow line, and continuously adjust the direction. For the latter part (left turn), extend your head out of the window, align the left window corner with the inner edge of the left yellow line, continuously adjust the direction, and finally straighten the car to the left.

13

4

Share

Do auxiliary roads need to wait for traffic lights?

Auxiliary roads need to wait for traffic lights. When entering the main road from an auxiliary lane, drivers must observe the straight-through traffic signal of the main road. Only when the signal light turns green can vehicles enter the main road. Methods for checking traffic signals when entering the main road from an auxiliary lane: If there are no traffic lights when entering the main road, you can turn on the left turn signal and follow the flow of green-light traffic into the main road. If the auxiliary road has turn signal lights, you must obey their instructions. Generally, these lights primarily allow auxiliary lane vehicles to directly enter left-turn lanes. If intending to turn left and proceed straight on the main road, merging is permitted when the green light is on, but attention must be paid to main road traffic. Consequences of running a red light on auxiliary roads: Running a red light on auxiliary roads will result in a fine and 6 penalty points. According to the "Road Traffic Safety Law of the People's Republic of China": Article 38: Vehicles and pedestrians shall pass in accordance with traffic signals; when traffic police are directing traffic on-site, they shall pass according to the police's instructions; on roads without traffic signals, they shall pass under the principles of safety and smooth traffic flow. Article 90: Motor vehicle drivers who violate road traffic safety laws and regulations regarding road passage shall be given warnings or fines. Where this law provides otherwise, punishment shall be imposed accordingly.

1

0

Share

What grade of engine oil is ACEA C3?

ACEA C3 is the third-grade engine oil in the European automobile manufacturing industry's testing and certification standards for automotive lubricants. The specific details are as follows: The ACEA C3 standard is higher than the API standard. ACEA C3 oil is a top-tier low-SAPS1 lubricant, primarily used in high-performance gasoline and light-duty diesel engines equipped with diesel particulate filters and three-way catalysts. These engines employ advanced after-treatment systems. The types of base oils are as follows: 1. Solvent-refined base oil: Contains higher sulfur content and unsaturated hydrocarbons (mainly aromatics). 2. Hydrotreated base oil: Features lower sulfur, nitrogen, and aromatic content. 3. Hydroisomerized base oil: Not only has low sulfur and aromatic content but also a very high viscosity index.

12

2

Share

Which is of higher grade, SN or SM engine oil?

SN grade engine oil has a higher quality level, while SM grade engine oil has a lower quality level. Engine oil grades are classified as SA, SB, SC, SD, SE, SF, SG, SH, SJ, SL, SM, and SN, with the grade increasing as the letters progress further in the alphabet. SN can replace SA-SM grade engine oils, but SM cannot replace SN grade engine oil. The differences between SN and SM engine oils are as follows: Different types of engine oil: In the classification of engine oils, SN grade engine oil is mainly composed of full synthetic oil, while SM grade engine oil is primarily semi-synthetic oil. Different environmental protection levels: SN grade engine oil has a higher environmental protection level; SM grade engine oil has a lower environmental protection level. Different high-temperature detergency: SN engine oil has higher high-temperature detergency than SM. SN grade engine oil provides better piston cleanliness, high-temperature deposit control, and low-temperature sludge control performance, meeting the performance requirements of the engine under various operating conditions. Different oxidation stability and anti-wear properties: SN grade engine oil has higher oxidation stability and anti-wear properties. This is because SN engine oil contains lower levels of phosphorus and zinc compared to SM engine oil, reducing wear on the three-way catalytic converter and thus enhancing the performance of the engine oil.

4

0

Share

How to reset the Sanyang oil check light?

The illuminated light indicates a lack of oil in the combustion oil reservoir. If this light comes on in a four-stroke vehicle, it usually indicates a malfunction in the oil pump or lubrication system, preventing proper oil circulation. Immediate inspection and repair are required. Below is relevant information: 1. Causes: This is typically due to a faulty oil pump resulting in insufficient oil pressure. Since oil is crucial for engine lubrication, promptly take the vehicle to a 4S shop or a certified repair facility for inspection to prevent engine damage. 2. Precautions: Avoid overfilling the oil. Excessive oil can lead to oil entering the combustion chamber during engine operation, or even being expelled through the exhaust pipe. This can cause unburned oil to accumulate carbon deposits and gum deposits on the piston top, valve seats, and valve oil seals, accelerating wear on mechanical components and potentially leading to premature failure of piston rings, pistons, and camshafts. Therefore, ensure the oil level remains strictly between the upper and lower marks on the dipstick.

17

1

Share

What are the requirements for driving a fire truck?

Fire trucks fall under the category of large, heavy, and medium-sized special-purpose vehicles, and drivers should possess a large truck driver's license, specifically a B2-level license. Below is an introduction to fire trucks: 1. Overview: A fire truck, also known as a fire engine, is designed and manufactured to accommodate firefighters and equip them with various firefighting tools or fire extinguishing agents as needed. 2. Function: These vehicles are used by fire departments for firefighting, auxiliary firefighting, or rescue operations. In most countries, including China, fire departments also utilize them for other emergency rescue purposes. Fire trucks can transport firefighters to disaster sites and provide them with a variety of tools for rescue missions. 3. Types: Fire trucks come in diverse types with complex functionalities and can be classified according to different standards. Based on the chassis load capacity, they include mini fire trucks, light fire trucks, medium fire trucks, and heavy fire trucks. By appearance and structure, they can be categorized as single-axle fire trucks, double-axle fire trucks, cab-over-engine fire trucks, and conventional-cab fire trucks. By fire extinguishing agent, they are further divided into water tank fire trucks, dry powder fire trucks, and foam fire trucks.

10

4

Share

What brand is Britax?

What does practicing laps mean in driving training?

Do auxiliary roads need to wait for traffic lights?

What grade of engine oil is ACEA C3?

Which is of higher grade, SN or SM engine oil?

How to reset the Sanyang oil check light?

What are the requirements for driving a fire truck?

Can Dried Gloss Gold Oil Be Washed Off?

What is the difference between NIO's second-hand car owners and first owners?

What is the Difference Between Headlights and High Beams?

Will the other party be fined for using the 12123 one-click vehicle relocation service?