What Aspects Does Automotive New Energy Technology Include?

1 Answers
StJocelyn
07/24/25 5:13pm
It includes power battery technology, motor technology, control technology, power management technology, and transmission coupling technology. Below is a partial introduction to new energy vehicles: Introduction: New energy vehicles refer to vehicles that use unconventional vehicle fuels as power sources (or use conventional vehicle fuels with new types of onboard power devices), integrating advanced technologies in vehicle power control and driving, resulting in vehicles with advanced technical principles, new technologies, and new structures. Types: Hybrid Electric Vehicles (HEV), Battery Electric Vehicles (BEV, including solar-powered vehicles), Fuel Cell Electric Vehicles (FCEV), and other new energy vehicles (such as those using supercapacitors, flywheels, and other high-efficiency energy storage devices).
Was this review help?
12
5
Share
More Forum Discussions

Where to Obtain the Environmental Label for a New Car?

The environmental label for a new car can be obtained at the Environmental Protection Bureau. Below is detailed information about the environmental label for cars: Overview: The vehicle environmental label is a classification mark issued by the state for motor vehicle emission standards, divided into two main categories: yellow and green. Relevant authorities review based on vehicle type and emission standards, and issue the environmental label upon approval. The purpose of the environmental label is to facilitate energy-saving and emission-reduction inspections and regular environmental checks for vehicles. Issuance Principles: Gasoline Vehicles: Vehicles that meet the National Phase I Emission Standards for motor vehicles are issued a green environmental label. In-use vehicles that do not meet the National Phase I Emission Standards or higher are issued a yellow environmental label. Diesel Vehicles: Vehicles that meet the National Phase III Emission Standards for motor vehicles are issued a green environmental label. In-use vehicles that do not meet the National Phase III Emission Standards or higher are issued a yellow environmental label.
14
1
Share

Does Compulsory Traffic Insurance Cover Water-Damaged Cars?

Compulsory traffic insurance does not cover water damage to your car because it is designed to compensate for damage to third-party vehicles and individuals. To claim for vehicle damage, you must have purchased vehicle damage insurance. Compulsory traffic insurance is mandatory by law, and without it, you cannot legally drive on the road. According to Article 90 of the Road Traffic Safety Law, traffic management authorities may impound the vehicle, require the owner to provide proper documentation or complete necessary procedures, and may issue a warning or impose a fine ranging from 20 to 200 yuan. Compulsory Traffic Insurance for Vehicles: Compulsory traffic insurance, officially known as 'Compulsory Liability Insurance for Motor Vehicle Traffic Accidents,' is a mandatory insurance where the insurer compensates victims (excluding the vehicle occupants and the insured) for bodily injury, death, or property damage within the liability limits in the event of a traffic accident. The premium is based on a nationally standardized rate. However, premiums vary depending on the vehicle type, primarily influenced by the number of seats. Compared to commercial third-party liability insurance, which has over 20 exemption clauses, compulsory traffic insurance covers a broader range, excluding losses caused intentionally by the victim, damage to the insured's own property, arbitration and litigation costs, and certain indirect losses. Additionally, compulsory traffic insurance provides compensation within the liability limits regardless of fault in the accident. Introduction to Electronic Insurance Policies An electronic insurance policy is a digital document issued by an insurer using digital signature software compliant with the PKI system and a corporate digital certificate, bearing the insurer's electronic signature. An insurance policy, or simply a policy, is the official written proof of the insurance contract between the insurer and the insured. It fully records the rights, obligations, and responsibilities of both parties and serves as the basis for fulfilling the contract. The policy is evidence of the insurance contract's validity. Advantages of Electronic Insurance Policies: Saves paper resources by eliminating the need for printed proof of insurance; Offers convenience and time savings, allowing access to information online anytime, anywhere; Allows for reissuance or resending if lost, with the option to print or mail a physical copy if needed; Simplifies management for insurers and traffic authorities by centralizing vehicle insurance information electronically.
20
0
Share

How Soon Can You Take the Subject 4 Test After Passing Subject 3?

There are three scenarios for the Subject 4 test timing after passing Subject 3: taking it directly in the afternoon of the same day; no appointment required within 9 days—you can take the Subject 4 test at the designated location with your ID within 9 days of passing Subject 3; or scheduling after 10 days, where success depends on current test-taker numbers, student priority, and temporary test center arrangements. Subject 4, also known as the theoretical driving test or driver's theory test, is part of the motor vehicle driver's license assessment. It covers safe and civilized driving operation requirements, safe driving knowledge under adverse weather and complex road conditions, emergency handling methods for situations like tire blowouts, and post-traffic-accident procedures. Subject 4 Test Notes: Test Duration: The test lasts 45 minutes, and answering 5 questions incorrectly (10 points) will terminate the session. Question Count: 50 questions are randomly selected from the Subject 4 question bank based on the type of license being tested, with each question worth 2 points. Question Types: The test includes single-choice questions (including true/false questions) and multiple-choice questions, featuring animation-based, image-based, scenario-recognition, and text-based questions. Retake Notes: Failing Subject 4 only requires retaking Subject 4, scheduled by the driving school without retake limits or fees. Subject 4 Test Tips: Strengthen weak areas by identifying error causes. For marked questions, avoid memorizing answers—review regulations, textbooks, or references to understand mistakes. Categorize and summarize questions, referring to the question bank's analysis to identify similar questions. For example, traffic signs like "Pedestrian," "Walking," "Pedestrian Crossing," and "Caution: Pedestrian Crossing" are easily confused—group them for clarity. Use memorization techniques: Many questions involve numbers—organize them for easier recall. There are three main driving test subjects: Subject 1, Subject 2, and Subject 3 (which has two parts). Subject 4 is the colloquial term for the "Safety and Civilized Driving Knowledge Test" under Subject 3, not a separate subject. Subject 1 covers traffic laws and regulations; Subject 2 assesses field driving skills; Subject 3 evaluates road driving skills and safety knowledge, with the latter taken after Subject 3.
6
0
Share

Do Small Cars Need to Warm Up in Winter?

Winter car warm-up is necessary; after the car has been parked for a long time, the engine oil flows back into the oil pan at the bottom of the engine. Reasons for warming up the car in winter: Lack of lubrication: After the car has been parked for a long time, the engine oil inside the engine flows back into the oil pan at the bottom. Therefore, when starting the engine after a long period of inactivity (such as overnight), the upper part of the engine is in a state without oil and lacks lubrication. It takes about 30 seconds after starting for the oil pump to circulate the oil to the parts of the engine that need lubrication the most, such as the pistons, connecting rods, and crankshaft. When driving immediately after starting the engine, as long as you don’t press the accelerator pedal hard for rapid acceleration and maintain low-speed operation, the effect is the same as idling. Low fuel supply temperature: Before the engine reaches its operating temperature (approximately between 90-110 degrees Celsius), the fuel supply system cannot effectively vaporize the gasoline completely due to the low temperature. When the gasoline is not vaporized and remains in a wet, liquid state, it is difficult to burn and start the engine. At this time, the choke valve comes into play, restricting some air from entering the cylinder to increase the gasoline/air mixture ratio and raising the engine speed to prevent stalling.
14
3
Share

What causes the ABS warning light to illuminate in the Emgrand EC7?

There are multiple states in which the ABS light may illuminate, with different causes and solutions for each state. Details are as follows: State 1: ABS warning light remains constantly lit (most common). Cause 1: The ABS wheel speed sensor's sensing area is covered by dirt, mud, or other contaminants, affecting its ability to detect the corresponding speed signal. This prevents the ABS control unit from determining the vehicle speed or calculating wheel slip rates, thus failing to issue appropriate commands for brake adjustment. Solution: Clean contaminants from the wheel speed sensor and adjust the gap between the sensor and the tone ring to restore normal function. Cause 2: Poor signal transmission due to loose system wiring connections or faulty ABS relay contacts. Solution: Inspect wiring connections and re-secure any loose connections. State 2: ABS warning light intermittently illuminates but turns off during acceleration. Cause: When multiple electrical components are in use, battery voltage drops below 10.5V. The light extinguishes as engine speed increases and voltage rises. Possible low system supply voltage due to poor terminal contact or grounding issues. Solution: Check battery specific gravity; inspect charging system; examine power supply components (e.g., voltage relay or poor power contacts). State 3: ABS warning light stays illuminated after engine start until engine IGFF position. Cause: Poor grounding connection of ABS hydraulic valve body; faulty wiring harness connector at hydraulic valve body; ABS control module malfunction. Solution: Loosen and re-tighten hydraulic valve body ground screw, cleaning contact surfaces if necessary; inspect connectors for excessive play; replace ABS or ABS/ASR control module. State 4: ABS warning light illuminates during high-speed driving. Cause: ABS control module detects excessive speed difference between rear and front wheels; incorrect tire or wheel rim specifications. Solution: Verify proper tire and wheel rim specifications as indicated on vehicle's fuel filler door label. State 5: ABS warning light intermittently flashes. Cause: Improper brake light switch adjustment; internal contact failure in brake lights. Solution: With engine running, depress brake pedal and manually push brake switch lever downward to reset position; replace brake light switch if needed. When the ABS warning light is illuminated, continued driving is not recommended. An active ABS light indicates a malfunction in the anti-lock braking system. During emergency braking, wheel lock-up may occur, causing loss of vehicle control and skidding, which prevents the driver from decelerating or adjusting the vehicle's trajectory, posing significant safety risks.
11
0
Share

What to Do When the Engine Warning Light Comes On in a Levin Hybrid?

The engine warning light may come on due to the following 7 main reasons: Sensor malfunction: The sensors mentioned here include those for coolant temperature, crankshaft position, air flow, intake air temperature, oxygen, etc. When these sensors are damaged, have poor contact, or their signals are interrupted, the vehicle's ECU cannot accurately obtain engine data, which may trigger the engine warning light. Fuel or oil quality issues: If the fuel or engine oil is not added as required by the manufacturer, it may cause engine wear, leading to the warning light coming on. Poor combustion of the air-fuel mixture: Poor combustion can cause engine carbon buildup or knocking. When detected by the oxygen sensor and reported to the ECU, the warning light will illuminate as a warning. Issues such as spark plug failure, ignition coil failure, fuel pump failure, or clogged fuel lines can all lead to poor combustion of the air-fuel mixture. Turbocharging issues: Problems with the intake boost piping or turbocharger can also cause the engine warning light to come on. The most common issue is turbocharger damage, accompanied by symptoms such as oil leaks, excessive oil consumption, reduced power, metallic noises, or blue/black smoke from the exhaust. Intake issues: If there is a problem with the vehicle's intake, it may lead to clogged engine piping, and in severe cases, trigger the engine warning light. A dirty air filter that is not cleaned regularly can cause intake problems. Exhaust issues: Exhaust system faults can also cause the engine warning light to come on. Common causes include faults in the rear oxygen sensor, catalytic converter, exhaust camshaft, or bearings, with the catalytic converter being the most frequent issue. Using leaded gasoline, lead or silicon-based lubricant additives, physical damage to the catalytic converter, or faults in the engine fuel supply system can easily lead to catalytic converter failure. Anti-theft system malfunction: If the vehicle's electronic anti-theft system malfunctions or if the anti-theft controller does not match the engine electronic controller, the anti-theft system may prevent the engine from operating normally, and the engine warning light will illuminate. If the engine warning light comes on, follow these steps: First, check if the engine is running normally and whether there are any issues such as shaking or smoke. If so, avoid restarting the engine. Note: Do not restart the engine if the red warning light is on. If the engine can be started, turn it off and wait for 5-10 minutes. Without pressing the brake, press the start button once or turn the key halfway to the "on" position without depressing the clutch. The vehicle will enter self-check mode after powering on. Wait for 5-10 seconds and observe whether the warning light on the dashboard turns off. If the warning light remains on, visit a service center as soon as possible to diagnose the issue. The service center can use a portable diagnostic tool to read the fault codes, identify the problem, and perform targeted repairs.
1
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.