What Are the Yellow Spots on a White Car?

1 Answers
VonDavid
07/30/25 8:31am
Yellow spots on a white car may be caused by tree sap or reactions with the paint. Here are several methods to remove them: 1. Use a clay bar: For stubborn yellow spots that won't wash off, continue using a clay bar. This is the simplest and most direct method, though it is time-consuming and requires careful attention to completely remove them. 2. Iron particle remover: The process is straightforward—wash the car first, dry it, spray on the iron particle remover, wait about ten minutes, and then wash the car again. 3. Polish with microcrystalline polishing wax: Polishing can be somewhat damaging to the paint surface, as it essentially removes a layer of paint, and it also costs money. 4. After cleaning, apply wax to the car body to prevent the recurrence of small yellow spots on the white paint.
Was this review help?
13
4
Share
More Forum Discussions

Does adding a spoiler to a sedan require registration?

Registration is required. Installing a spoiler on a car is considered an alteration to the vehicle's appearance, and the owner must register the modification with the vehicle management office in advance. If a spoiler is installed without registration, the traffic management department will detain the vehicle, confiscate the illegal modification, order restoration to the original condition, and impose a fine according to the law. Here is relevant information: 1. After the modification is completed, the vehicle license must be re-photographed and replaced to ensure that the photo on the license matches the modified vehicle, so that the car can pass annual inspections and routine safety checks. The requirement for adding a spoiler is that it should not exceed the overall dimensions of the vehicle after installation. 2. The main function of a car spoiler is to provide sufficient downforce, reducing lift at the rear of the vehicle, ensuring the car remains firmly on the road and maintains stability during driving. 3. If a vehicle owner wishes to change the body color, replace the engine, or alter the body or frame, they are no longer required to apply to the vehicle management office in advance. They can first make the changes (such as altering the vehicle color, adding body kits, or replacing the engine) and then apply for modification registration at the vehicle management office within 10 days.
6
0
Share

How long does it take to repaint a section of a car?

It usually takes about a week. Disassembly and reassembly take one day, and the preparation work, including priming and base coating, depends on the extent of the damage to the car body, which is the most time-consuming part. If the damage is not severe, this process typically takes three days up until the painting stage. Below is some relevant information: 1. Automotive paint is generally baked-on paint. In car factories, after the frame and body shell are welded (and sometimes manually repaired), the next step is painting. Usually, the first step is applying the primer. The bare car body is dipped into a syrup-like paint tank, then removed and baked to dry the primer. It is then sent to a dust-free workshop where the topcoat is applied using electrostatic spray painting. After that, it is baked at around 200 degrees Celsius. For higher-quality finishes, a layer of clear coat is added. This completes the painting process. 2. There are generally several types of topcoats: standard paint, metallic paint, and pearl paint. Standard paint consists of resin, pigments, and additives. Metallic paint includes aluminum flakes, which give it a shiny appearance. Pearl paint incorporates mica particles. Mica is composed of very thin flakes, which create directional reflections and produce a colorful effect. If metallic paint is combined with a clear coat, the car's finish will look very bright and attractive.
1
4
Share

Can Tesla Replace Its Battery?

Tesla can replace its battery, but the cost is relatively high. Below is some information about Tesla: 1. Introduction: Tesla is an American electric vehicle and clean energy company that manufactures and sells electric cars, solar panels, and energy storage systems. Headquartered in Palo Alto, it was founded on July 1, 2003, by Martin Eberhard and Marc Tarpenning. The founders named the company "Tesla Motors" in honor of the physicist Nikola Tesla. 2. Main Models: Tesla's vehicle lineup includes the Roadster, Model S, Model X, Model 3, and Model Y.
6
4
Share

How to Replace the Camshaft Oil Seal on a Chevrolet Cruze?

The method for replacing the Camshaft oil seal on a Chevrolet Cruze is as follows: 1. First, rotate the crankshaft pulley to the position of the first cylinder. There is a small dot on the crankshaft pulley that should align with the longest protruding strip on the front oil seal housing. Maintain this position, then install the rear crankshaft oil seal. Note that there is a small dot on the rear crankshaft oil seal housing that should align with an empty point on the pulley when installing it onto the crankshaft. 2. The crankshaft seal is located inside the crankshaft pulley, and the rear crankshaft oil seal is situated at the flywheel inside the connection between the engine and the transmission. 3. After assembling the crankshaft into the cylinder block, install the main bearing cap. Before installing the rear main bearing cap, apply sealant to the rear part of the mating surface, then tighten according to the specified torque. The tightening torque for the main bearing cap bolts must be followed. 4. After assembling the crankshaft, when installing the rear crankshaft oil seal, use a specialized tool—the crankshaft thick oil seal press tool—to press the rear oil seal from the rear end of the crankshaft. 5. During the pressing process of the oil seal, ensure that the oil seal remains level at all times.
20
1
Share

What Could Be the Reason When a Car Fails to Start?

There are 5 possible reasons why a car fails to start: 1. Car battery is dead or damaged: A dead battery requires jump-starting with another battery or using the universal push-start method. Failure to start may be caused by leaving headlights on for an extended period or an expired battery lifespan. Generally, replacing the battery according to the maintenance manual will resolve the issue. 2. No fuel pressure in the engine's fuel supply line: This situation often occurs on extremely cold mornings, caused by long-term contamination in the fuel line. At very low temperatures, water mixed with debris can block the fuel line, resulting in failure to start. 3. Car lacks antifreeze: Adding water or low-quality antifreeze can cause the entire cooling system to freeze in extremely cold winter conditions, leading to a cracked engine block. This prevents the water pump from functioning, resulting in failure to start and potential damage to other engine components. 4. Excessive carbon buildup in the vehicle: The solution is to frequently drive at highway speeds to reduce carbon deposits. 5. Steering wheel lock engaged: The steering wheel lock is a simple anti-theft feature. When the car is turned off, rotating the steering wheel from its centered position to a certain angle in one direction will activate the lock. Solution: Turn the steering wheel left and right while pressing the engine start button to release tension and unlock the steering wheel.
19
2
Share

How Many Turns of the Steering Wheel for Turning?

Here is the relevant introduction on how many turns of the steering wheel are needed when turning: 1. Right turn: one turn of the steering wheel: For a right turn, one turn of the steering wheel is generally sufficient. If it's a large intersection, you may feel the need to turn more during the right turn, but you should stop turning. If it's a small intersection and the angle isn't enough, you can adjust slightly. The angle of the steering wheel for a right turn depends on the size of the intersection—the larger the intersection, the smaller the angle of the steering wheel turn. 2. Left turn: half a turn of the steering wheel: Turning too much at a large intersection may lead you into oncoming traffic. Especially when turning left across two or three lanes, excessive steering in the right lane can interfere with left-turning vehicles in the left lane. The correct method is to turn the steering wheel slightly less than half a turn initially, then adjust if needed until it feels right. Additional Information: Precautions for turning: 1. For a tight turn, turn the steering wheel as much as possible, then gradually straighten it after completing the turn. 2. For a wide turn, turn the steering wheel slowly. 3. Beginners often focus only on what's directly ahead or to one side during a turn, neglecting blind spots, which can lead to hitting the curb or causing a scrape. 4. Always check for obstacles below the rearview mirrors; if necessary, open the door and look before turning.
20
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.