What are the wheel hub specifications for the Mitsubishi Lancer EX?

Does Entering the Waiting Zone Count as Running a Red Light?

Entering the waiting zone does not count as running a red light. If you have already crossed the stop line and are continuing to make a left turn when the red light turns on, it is not considered running a red light. More details are as follows: 1. When the straight-ahead signal in the same direction turns green, vehicles in the left-turn lane must move forward into the waiting zone and wait for the signal. The 'left-turn waiting zone' is exclusively for left-turning vehicles. Even if the left-turn signal is red when the straight-ahead signal turns green, left-turning vehicles are allowed to enter the 'left-turn waiting zone' at the intersection and wait until the left-turn signal turns green before proceeding. 2. It is important to remind drivers that the left-turn waiting line is not a 'stop line.' If both the straight-ahead and left-turn signals are red, all vehicles must wait behind the original stop line. 3. If a vehicle has just crossed the stop line when the light turns red but stops immediately, this will not be penalized as running a red light. However, if there is noticeable movement after crossing the line, penalties will apply.

2

4

Share

Why is the clutch getting heavier?

There are several reasons why a car's clutch may become increasingly heavy: 1. When the clutch pedal is released, it should return quickly and accurately to its standby position. A return spring is typically designed at the pedal. If the heavy pedal phenomenon occurs after replacing the spring, it is likely that the clutch pedal return spring has too much tension. 2. Many car clutches use an assist system, which normally makes operation easier. However, if the clutch assist cylinder fails, it may result in insufficient assistance, ultimately causing the clutch pedal to feel very heavy when pressed. 3. Most of the power driving the clutch booster comes from the compressed air in the air reservoir. If the pressure of the compressed air leading to the booster is too low, it can cause insufficient assistance. Therefore, when such a fault occurs, the compressed air pressure to the clutch booster should be checked first.

15

1

Share

Where is the cabin air filter located on the Changan CX30?

The cabin air filter of the Changan CX30 is located beneath the wiper panel under the engine hood. You'll need to remove the wiper panel to access it. Since this involves wiper removal, it's recommended to have it replaced at a 4S dealership or auto repair shop. Manufacturers generally recommend replacement every 20,000-30,000 kilometers. Here are the functions of the cabin air filter: 1. Ensures tight sealing against the housing to prevent unfiltered air from entering the cabin. 2. Filters out solid impurities such as dust, pollen, and abrasive particles from the air. 3. Adsorbs moisture, soot, ozone, odors, carbon oxides, SO2, CO2, etc., with strong and lasting moisture absorption capability. 4. Prevents windshield fogging to maintain driver visibility and ensure driving safety; provides fresh air to the cabin, preventing occupants from inhaling harmful gases and effectively eliminating bacteria and odors. 5. Maintains clean cabin air to prevent bacterial growth and creates a healthy environment; effectively separates solid impurities like dust, core powder, and abrasive particles; efficiently blocks pollen to prevent allergic reactions that could affect driving safety.

2

4

Share

What is the battery model for the Dongfeng Nissan Sylphy remote control?

The battery model for the Dongfeng Nissan Sylphy remote control is a 3V CR2025 button cell. The remote key utilizes the wireless remote control function of the central locking system, allowing you to open and lock the doors from a distance without inserting the key into the lock. The remote key generally consists of the following two parts: 1. Transmitter. Composed of a transmission switch, transmission antenna (keypad), integrated circuit, etc. It contains an identification code storage circuit and an amplitude modulation circuit, with a button-type lithium battery installed on the opposite side of the circuit. The transmission frequency is selected according to the radio standards of the country of use, and the transmission switch sends a signal each time it is pressed. 2. Receiver. After the transmitter sends the identification code using shortwave modulation, it is received by the car's shortwave antenna and processed by the distributor into the shortwave high-frequency amplification processor of the receiver's electronic control unit for demodulation. The demodulated identification code is then compared; if it is the correct code, it is input into the control circuit to activate the actuator.

14

2

Share

How to Use Anti-Skid Control

The method to use anti-skid control: The switch is located below the left side of the steering wheel. Simply press it briefly to turn it off, and press it briefly again to turn it back on. The principle of anti-skid control is: The ABS electronic control unit calculates and analyzes the signals from the wheel speed sensors to determine the wheel slip rate and vehicle speed. The electronic control unit then adjusts the wheel slip rate by controlling the throttle opening and brake pressure. In vehicles equipped with an anti-skid system, the system is enabled by default when the car is powered on. The anti-skid system primarily analyzes data from sensors to ensure optimal dynamic balance during driving.

14

4

Share

Can Tire Pressure Monitoring Be Installed as an Aftermarket Addition?

Tire pressure monitoring can indeed be installed as an aftermarket addition. The tire pressure monitoring system is a type of active safety device that can promptly alert the driver when there are signs of danger in the tires, prompting them to take appropriate measures to avoid serious accidents. With a tire pressure monitoring system, tires can consistently operate within the specified pressure and temperature ranges, thereby reducing tire damage and extending their lifespan. Reasons for the tire pressure monitoring alarm to activate include: 1. Tire repair or inflation without resetting the tire pressure data; 2. Dead battery in the tire pressure sensor; 3. Leaky valve stem; 4. The vehicle has been idle for an extended period.

7

4

Share

What are the wheel hub specifications for the Mitsubishi Lancer EX?

Does Entering the Waiting Zone Count as Running a Red Light?

Why is the clutch getting heavier?

Where is the cabin air filter located on the Changan CX30?

What is the battery model for the Dongfeng Nissan Sylphy remote control?

How to Use Anti-Skid Control

Can Tire Pressure Monitoring Be Installed as an Aftermarket Addition?

Is the Volkswagen Tharu fuel-consuming with the 1.4T engine?

Can Disinfectant Corrode Car Paint?

What brand is the engine of the Mazda6?

What are the differences between the BYD Song Pro Elite and Luxury models?