What are the warning symbols on the car dashboard?

What are the body dimensions of the Touran?

The body dimensions of the Touran are: length 4527mm, width 1829mm, height 1659mm, with a wheelbase of 2791mm. Taking the 2021 Touran as an example, it is an MPV with a minimum ground clearance of 120mm and a body weight of 1515kg. The 2021 Touran features a front MacPherson strut independent suspension and a rear four-link independent suspension. It adopts a front-engine, front-wheel-drive layout, equipped with a 1.4T turbocharged engine producing a maximum horsepower of 150PS and a maximum torque of 250Nm. The maximum power output is 110kW, paired with a 7-speed dual-clutch transmission.

5

2

Share

How to Tell If a Car Is Out of Gas?

To determine if a car is out of gas, check the fuel gauge. The amount of fuel is controlled by a float sensor inside the fuel tank. The sensor monitors the fuel level and sends this signal to the ECU, which then analyzes the data and displays it on the dashboard. If the fuel level is too low, the low fuel warning light will illuminate. Tips for refueling: 1. When the fuel tank is down to a quarter full, it's time to refuel—don't wait until it's empty. 2. Avoid filling the tank to the brim; leave some space. 3. Do not mix different types of fuel; do not add diesel or kerosene to gasoline. 4. Follow the fuel grade requirements listed on the fuel tank cap. 5. Refuel at large or medium-sized gas stations. Using low-quality gasoline containing sulfur can poison the oxygen sensor.

1

0

Share

What are the reasons for no response when starting a car?

The reasons for no response when starting a car are: 1. There is a problem with the control circuit of the starter; 2. The starter brush is faulty; 3. The battery voltage is insufficient; 4. There is an issue with the relay; 5. Poor contact of the starter's magnetic switch. The solutions for no response when starting a car are: 1. Check if there is a problem with the control circuit of the starter; 2. Check if the starter brush is faulty and replace it in time if there is a problem; 3. Adjust the battery voltage; 4. Check if there is an issue with the relay; 5. Check the contact condition of the starter's magnetic switch; 6. Check if the starter wire is loose or detached, and whether the switch or adsorption switch is malfunctioning.

15

0

Share

Which company produces the XPeng P7?

XPeng P7 is produced by Xpeng Motors Technology Co., Ltd. Taking the 2021 XPeng P7 as an example, its body structure is a 4-door, 5-seater sedan with dimensions of 4880mm in length, 1896mm in width, and 1450mm in height. It has a wheelbase of 2998mm, front track of 1615mm, rear track of 1621mm, a trunk capacity of 440 liters, and a curb weight of 1935kg. The 2021 XPeng P7 features a double-wishbone independent front suspension and a multi-link independent rear suspension. It is equipped with a permanent magnet synchronous motor paired with a fixed gear ratio transmission.

4

Share

How to Switch Between S Gear and D Gear While Driving?

The method to switch between S gear and D gear while driving is to shift directly without the need to press the brake or stop the vehicle. S gear stands for Sport mode, where the car prioritizes high performance. When shifted into S gear, the transmission delays upshifting to allow the engine to deliver greater power. D gear stands for Drive mode, where the vehicle focuses on comfort and fuel efficiency. The correct way to use an automatic transmission is: 1. Start the vehicle in P or N gear; shift out of P gear by pressing the brake, turning on the power, pressing the brake again, shifting to N gear, and then moving to D gear after ignition to drive forward directly. 2. When switching between N, D, and L gears, there's no need to press the shift button. However, when shifting from L gear to lower restricted gears, press the shift button, but shifting from lower to higher gears does not require pressing the shift button. 3. Do not shift into N gear to coast while driving. 4. Do not push into P gear while driving. 5. After driving, the vehicle must be turned off and shifted into P gear before the key can be removed.

10

5

Share

What is the reason for the sound when stepping on the brake in P gear of an automatic transmission car?

The reason for the sound when stepping on the brake in P gear of an automatic transmission car is: there is a locking mechanism inside the gear lever. After stepping on the brake pedal, the locking mechanism will unlock, and the sound at this time is a normal phenomenon. Introduction to automatic transmission car gears: 1. P gear is the parking gear, used for long-term parking of the vehicle; 2. R gear is the reverse gear, which is engaged when the vehicle needs to reverse; 3. N gear is the neutral gear, which is engaged when the vehicle is parked for a short time without turning off the engine; 4. D gear is the drive gear. When the gear lever is placed in D gear, the vehicle will automatically shift gears based on throttle opening and speed data; 5. S gear is the sport mode, making the vehicle drive more sportily; 6. M gear refers to the manual mode. When the gear lever is engaged in M gear, shifting is done manually by the driver; 7. L gear is the low gear.

15

3

Share

What are the warning symbols on the car dashboard?

What are the body dimensions of the Touran?

How to Tell If a Car Is Out of Gas?

What are the reasons for no response when starting a car?

Which company produces the XPeng P7?

How to Switch Between S Gear and D Gear While Driving?

What is the reason for the sound when stepping on the brake in P gear of an automatic transmission car?

What is the 0-100 km/h acceleration time of the Excelle?

Can the license plate be retained when a vehicle is scrapped?

What type of transmission does the Compass have?

How to Set Up One-Touch Power Window in a Car?