What are the uses of Toyota shift-lock?

1 Answers
VonMax
07/29/25 4:25pm
Toyota shift-lock is a parking gear that enables the vehicle to remain stationary on slopes by locking the axle through the gear position. It is a special neutral gear that mechanically locks the transmission output shaft to secure the vehicle. Its function is to act as a brake after parking, preventing the vehicle from moving. Relevant information about joint-venture vehicles is as follows: Introduction: A project jointly established by Chinese and foreign investors. Chinese investment methods include granting land and factory usage rights and capital, while foreign investors provide brands, technology, capital, and talent. Joint-venture vehicles are the products of such collaborations. Foreign parties provide technology, talent, and brands for domestic assembly, but core technologies remain controlled by foreign entities. Joint-venture brands under the FAW Group include: FAW-Volkswagen, FAW-Audi, FAW-Mazda (all produced in Changchun, Jilin), and FAW-Toyota (produced in Changchun, Jilin; Tianjin; and Chengdu, Sichuan).
Was this review help?
12
5
Share
More Forum Discussions

How to Reset the Car Engine Malfunction Light?

Car engine malfunction light can be reset by: 1. Using higher octane gasoline; 2. Replacing the oxygen sensor; 3. Replacing the mass airflow sensor; 4. Cleaning the spark plugs; 5. Replacing the engine; 6. Replacing the coolant temperature sensor. Reasons for engine malfunction light illumination include: 1. Poor quality or substandard gasoline; 2. Faulty oxygen sensor; 3. Malfunctioning mass airflow sensor; 4. Spark plug carbon buildup; 5. Engine knocking; 6. Damaged coolant temperature sensor; 7. Engine misfire. Causes for car engine warning light activation are: 1. Sensor damage, poor connection or signal interruption; 2. Poor engine maintenance; 3. Low-quality fuel or engine oil; 4. Incomplete fuel mixture combustion; 5. Faulty spark plugs or ignition coils; 6. Fuel pump failure or clogged fuel lines; 7. Clogged cabin air filter.
15
3
Share

Where is the cigarette lighter fuse in the BMW 520?

The front cigarette lighter fuse is located inside the glove compartment cover on the passenger side; the rear cigarette lighter fuse is located inside the side cover panel in the trunk. The exact position of the cigarette lighter fuse will be clearly indicated on the fuse box cover. Instructions for locating the cigarette lighter fuse: Before searching for the fuse, for safety reasons, turn off the engine and power supply; correctly locate the fuse box position and use a pry tool to remove the cover panel; check the position of the cigarette lighter fuse on the cover panel; then remove the fuse protection cover, use a test pen to measure the fuse contacts; use a clip tool to remove the blown fuse and replace it with a new one. How to use the cigarette lighter: Insert the cigarette lighter into the power socket and press down to lock it; when the heating element reaches the temperature for automatic ejection, or wait about 5 to 8 seconds until the heating element turns red, then manually remove it.
5
0
Share

How to distinguish between Porsche Cayenne and Macan?

Porsche Cayenne was launched earlier than the Macan and is positioned higher than the Macan, with the Cayenne being a mid-to-large-sized SUV. Here is the relevant information: 1. The Macan is a mid-sized SUV, which means it is in the same class as the Audi Q5 and Mercedes-Benz GLK, while the Cayenne is a mid-to-large-sized vehicle, so it naturally has a larger body size than the Macan, and of course, the interior space is also superior in the Cayenne. 2. The top-of-the-line Macan Turbo model is equipped with a 3.6L twin-turbocharged engine, delivering a maximum horsepower of 400 hp, paired with a 7-speed dual-clutch transmission, achieving a 0-100 km/h acceleration time of just 4.8 seconds. This makes the Cayenne, at the same price, with an acceleration time of 7 seconds, seem almost unattainable compared to the Macan.
4
2
Share

What is the voltage of the Honda CRV battery?

The battery model for the Honda CRV is 46B24LS, with a rated voltage of 12V and a rated current of 45Ah. The original vehicle is equipped with a Yuasa (YUASA) maintenance-free starting battery. Precautions for using the Honda CRV battery: During the use of the car, the battery plays a crucial role. If it cannot supply power normally, it will cause engine problems or stalling. Generally, the battery needs to be replaced every 2 years or so, but with good maintenance, its lifespan can be extended to up to 4 years. Important factors affecting battery life include the condition of the car, road conditions, and the driver's habits. Regularly check the car's battery: In summer, it should be checked weekly, while in winter, it should be checked every two weeks. Since new cars have better alternator performance, the battery can be fully charged, so new cars generally save battery power.
8
3
Share

What causes the battery light to flash in a Santana?

The reasons for the battery light flashing in a Santana are as follows: Oxidized battery terminals: Check the battery terminals for oxidation. If there is oxidation, clean it yourself. Battery discharge: Measure the battery voltage with a multimeter when the engine is off. If it's above 12 volts, the battery is fine; otherwise, the battery is damaged. Alternator fault: If there's a charging issue, meaning the alternator is not charging properly, measure the battery voltage with a multimeter when the engine is running. If it's above 14 volts, the alternator is fine; if it's below 14 volts, the alternator is faulty. Battery aging: The battery light flashes because the battery is not supplying enough power or the battery is too old to hold a charge. This is a normal reaction when a Santana's battery has been left unused for a long time without timely recharging.
4
4
Share

How much engine oil should be added to the Honda Shashark?

Honda Shashark usually requires 700ml of engine oil. Methods for selecting engine oil: There are three main factors to consider when choosing engine oil: API grade, viscosity grade, and base oil quality. For motorcycles like the Honda Shashark, an API grade of SF or above is sufficient. The viscosity grade can be 10W-30 or 10W-40, and the base oil quality can be mineral oil, semi-synthetic, or fully synthetic oil depending on the situation. The specific oil change model can be referred to in the vehicle's user manual. Methods for checking engine oil level: The engine oil level can be checked using the dipstick in the oil pan. When the engine is cold, pull out the dipstick, wipe it clean, reinsert it, and then pull it out again. As long as the oil level is between the MIN and MAX marks, it is acceptable.
4
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.