What are the tips for Motorcycle License Tests Subject 2 and 3?

2 Answers
StLucia
09/04/25 6:04am
The tips for Motorcycle License Tests Subject 2 and 3: master riding skills, avoid stalling throughout the test, and maintain steady speed. Detailed explanations are as follows: Master riding skills: Before the test, make sure to practice your riding skills thoroughly. If the training motorcycles at the driving school are insufficient, you can borrow one yourself. Be sure to practice in a spacious and uninhabited area. As the saying goes, practice makes perfect—repeated practice is always beneficial. Avoid stalling throughout the test: When navigating through the poles, proceed slowly and avoid rushing. Be mindful not to let your feet touch the ground, as this will result in point deductions. However, when crossing the bridge, one foot is allowed to touch the ground once, though it's best not to touch the ground at all. Maintain steady speed: When crossing the bridge, do not ride too slowly, as a slight mistake could cause you to fall off. At this point, ensure you provide enough throttle and maintain a steady speed. When approaching the next bridge, always align the front and rear of the motorcycle properly beforehand.
Was this review help?
7
3
Share
VanSerenity
09/16/25 7:01am
I've been riding motorcycles for almost ten years, and I've long mastered the tricky parts of the Subject 2 and Subject 3 tests. The key is to first build a solid foundation—for Subject 2's slalom test, maintain slow and steady throttle control, don’t just stare at the cones but look ahead to keep balance, and practice emergency braking and hill starts to avoid rolling back. For Subject 3’s on-road test, stay focused: observe traffic lights early, always check mirrors before changing lanes with turn signals, and park precisely without blocking traffic. Simulate test scenarios in open areas, and practice clutch-throttle coordination until it becomes instinct. Staying relaxed is crucial—if nervous, take a ride to calm down with deep breaths. Don’t let one failure discourage you; learn from it and try again. Find a skilled instructor to save time. Always prioritize safety—wear helmets and gear while practicing. In short, persistence and practice lead to success—don’t rush for quick results.
Was this review help?
14
3
Share
Expand All
More Forum Discussions

What is the fuel consumption of the RS7?

RS7 owner average fuel consumption: average fuel consumption of 17.8 liters per 100 kilometers, official fuel consumption: 10.3 liters. Here is additional information: Engine: The Audi RS7 is a mid-to-large-sized imported luxury car, originally equipped with a 4.0T V8 turbocharged engine, providing ample power. Design style: The Audi RS7 concept car was designed by a designer from Austria, and the car's exterior design incorporates the styles of several Audi models. The side body and rear design are very similar to the Audi R8, while the car doors adopt Lamborghini's classic scissor door design.
4
1
Share

How to Tighten Motorcycle Mirrors?

First, take a wrench and loosen the screws on the mirror to make them slack. Hold the mirror with your hand and rotate it counterclockwise until the mirror comes off. Place the removed mirror on the ground to inspect the extent of damage. Adjust the mirror angle and use the wrench to tighten the screws on the mirror.
8
2
Share

How to Reset the Maintenance Reminder for the 2020 Magotan?

First, turn the ignition key of the Volkswagen Magotan to the ON position to illuminate the car's dashboard. Then, press the down button on the steering wheel to locate and select the maintenance option. After entering the maintenance interface, a selection screen will appear; choose the reset option. Finally, the vehicle's maintenance reminder will be canceled.
14
1
Share

What is the correct method for B2 pressing the pancakes?

Use the raised left ridge inside the car hood to align with the direction of the front 1st and 2nd pancakes. When the car is about to pass the 4th pancake, center the steering wheel. Once the car is about to pass the 5th pancake, straighten the steering wheel.
8
1
Share

How to Adjust the Angle of the Wiper Linkage Rod?

First, turn the key to the ON position, activate the wipers, then turn off the switch and the key. At the base of the wiper arm, remove the dust cover, use an appropriate wrench or socket to loosen the screw until it can be rotated. Then lift the wiper blade and gently shake it. Once it becomes loose, position the wiper blade to the desired angle, tighten the screw, and replace the dust cover.
15
2
Share

Difference Between TPR Wheels and Rubber Wheels?

TPR tires are tire products that do not require high wear resistance or strength, whereas rubber tires used in vehicles demand high load-bearing capacity, wear resistance, and mechanical strength. Here is additional information: TPR tires: Primarily used for casters, cart wheels, and toy tires where load-bearing capacity and wear resistance strength requirements are not very high. They are typically made of pure TPR material or a composite of TPR with other materials like PP or ABS through injection molding. Rubber tires: Usually vulcanized rubber tires, used for various vehicle tires. Due to the high demands on load-bearing capacity, wear resistance, and mechanical strength, the material requirements for these tires are stringent. Besides vulcanization, materials like steel wires and nylon fabric are incorporated into rubber tire products to enhance impact resistance and anti-burst performance.
11
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.