What are the tips for memorizing the route map in Subject 3?

2 Answers
OEmmett
07/29/25 2:03am
You can use paper to note down the sequence of road sections, such as straight driving first, followed by traffic lights, and then passing through deceleration zones, etc. Here is the relevant introduction: 1. Reasons for nervousness: Being unfamiliar with the Subject 3 route is not the most important reason for nervousness; lack of technical proficiency is. However, this statement is not entirely accurate, as all are beginners learning to drive, and their skills are generally average. Some coaches are more responsible and may take students around the test site several times before the exam to familiarize them with the area, while others might even allow students to take the exam without any simulation training. 2. Mindset: If you encounter an irresponsible coach, you should spend more time during regular practice to memorize driving techniques. Some students perform effortlessly during training but repeatedly fail in the actual exam, so developing a good mindset is also crucial.
Was this review help?
15
1
Share
MacAdaline
08/12/25 6:04am
When I was preparing for my driving test (Road Test Part 3), I struggled to memorize the route at first and it took me quite a while to figure out the trick. The most effective method was practicing daily—driving the same route repeatedly while focusing on one or two new landmarks each time, like which tree marked the turn or where to accelerate after passing a bridge. I drew a small map and kept it in my bag, glancing at it during downtime, and paired it with phone recordings to review road details. Practicing with friends also helped—we reminded each other of traffic light positions and lane-change timings, leveraging collective memory. After sticking to this routine for a week, the route became second nature, and my nervousness during the actual test significantly decreased.
Was this review help?
10
2
Share
Expand All
More Forum Discussions

What causes gear shift jerking in the Mercedes-Benz GLK300 transmission?

Mercedes-Benz GLK300 transmission gear shift jerking may be caused by solenoid valve damage or transmission control module failure. The specific reasons and solutions are as follows: Solenoid valve damage: If sludge in the transmission oil circulates and blocks the oil passages in the valve body, gear shift jerking will occur. Prolonged operation under this condition can lead to a series of transmission issues such as overheating, impact, and slippage. The solution is to repair the solenoid valve. Transmission control module failure: The control module serves as the central heart of the transmission, responsible for communicating with the vehicle's main computer, collecting signals, and sending commands. Module failure primarily affects these instruction transmissions. The solution is to perform repair work.
13
2
Share

What causes the Audi A6L to shake when starting?

Audi A6L shaking when starting is caused by abnormalities in the intake system, engine carbon buildup, etc. The specific reasons and solutions are as follows: Abnormalities in the intake system: When the engine is running, the driver controls the throttle opening via the accelerator pedal to adjust the intake volume and regulate engine operation. Issues such as insufficient power and poor acceleration may result from damage to certain components of the intake system. The solution is to replace the relevant parts. Engine carbon buildup: Carbon deposits on the engine's valves and intake passages can absorb an appropriate amount of fuel, failing to achieve the required power performance, leading to shaking when the car starts. The solution is to perform a system cleaning.
13
5
Share

What is the solution for the 3008 burning engine oil?

To resolve the issue of burning engine oil, it is essential to address carbon buildup on the piston rings, wear between the pistons and cylinder walls, valve stem seals, and crankshaft seals, with particular attention to solving the crankshaft seal problem. Burning engine oil occurs when oil enters the engine's combustion chamber and mixes with the air-fuel mixture for combustion. The phenomenon of 'burning engine oil' in a vehicle can lead to premature failure of the oxygen sensor, increased carbon deposits in the combustion chamber, unstable idling, reduced acceleration power, higher fuel consumption, and excessive exhaust emissions. In severe cases, insufficient engine lubrication can cause irreparable damage or even complete engine failure, significantly increasing repair costs and posing potential safety hazards.
5
2
Share

What is the difference between second gear and reverse gear?

The difference between second gear and reverse gear lies in their different positions. Car owners need to pay attention to the positions of these two gears while driving. Below is a detailed introduction about car gears: 1. Speed range: First gear corresponds to a speed of 0-5km/h. Second gear corresponds to 5-20km/h, third gear to 20-40km/h, fourth gear to 40-60km/h, and fifth gear to 60-100km/h. 2. Gear shifting timing: Generally, the optimal time to shift gears is when the engine speed reaches 2000r/min, and should not exceed 2500r/min. For some high-displacement and high-power engines, shifting around 3000r/min is acceptable.
5
4
Share

Does the CS85 have a four-wheel drive model?

Currently, the CS85 does not have a four-wheel drive model. It is a front-engine, front-wheel-drive vehicle. Front-wheel drive refers to a car design where the engine only drives the front pair of wheels, a configuration used by most sedans today. Some urban SUVs are equipped with on-demand four-wheel drive technology, which means the vehicle is primarily front-wheel drive, but when the front wheels slip, power is distributed to the rear wheels. Urban SUVs with on-demand four-wheel drive have better off-road capability than front-wheel-drive SUVs, and they also have relatively lower fuel consumption. The Great Wall CS85 uses a MacPherson strut independent suspension for the front and a multi-link independent suspension for the rear.
15
3
Share

What are the differences between Kawasaki Z400 and Ninja 400?

The main differences between Kawasaki Z400 and Ninja 400 are as follows: 1. Different appearances: Due to their different positioning, there are obvious differences in appearance between these two models. The Ninja 400 adopts the standard fully enclosed design of a sports car, while the Z400 has been simplified, resulting in very few wrapping parts on the overall appearance. Although there are differences in their overall appearance, both belong to the category of stylish and beautiful models. 2. Different riding postures: The riding posture of the Ninja 400 is relatively more aggressive, while the Z400 is more upright. This difference mainly comes from the handlebar designs adopted by the two models. The Ninja 400 uses the split low handlebars commonly used in sports cars, while the Z400 adopts a one-piece handlebar.
7
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.