What are the techniques for beginners to stabilize the throttle?

3 Answers
ODiana
07/29/25 10:37am
After the car stalls, if the key switch is in the ON position, do you need to turn the key to the OFF position and then restart, or can you directly start the ignition from the ON position? Below is an analysis of the causes of sudden stalling: 1. Circuit failure: During driving, the engine may stall due to low-voltage power interruption. If the stalling is caused by a short circuit in the low-voltage circuit, intermittent stalling may occur subsequently. 2. Component failure: Focus on checking the ignition coil and electronic ignition module. Problems with these components can lead to intermittent stalling. 3. Fuel system failure: Automatic transmission vehicles generally do not stall unless there is an issue with the fuel system.
Was this review help?
1
5
Share
StManuel
08/13/25 3:12pm
Maintaining steady throttle control is a fundamental skill for beginners, which leads to smoother driving. Find a safe open area to practice: keep your right heel planted on the floor and gently press the accelerator with the ball of your foot—avoid using excessive force. Imagine stepping on an air cushion—apply gradual pressure to about 1/4 depth, and the speed will increase evenly. Avoid stomping suddenly, as it may cause engine jerking or loss of control. Having taught many trainees, I recommend focusing on the speedometer after starting, adjusting the throttle to maintain 20-30 km/h. Apply slightly more pressure uphill and ease off on flat roads. Automatic transmissions make this easier, while manuals require clutch coordination. Practice a few times weekly to build muscle memory. Also, ensure your seat is adjusted comfortably to prevent foot fatigue. Once mastered, stop-and-go city traffic becomes effortless—and you’ll save fuel too.
Was this review help?
13
1
Share
Expand All
DelIsabela
10/07/25 6:02am
When I first learned to drive, I also kept pressing the accelerator unevenly, making the car jerk back and forth, which was quite scary. Later, I realized the key is to control the throttle gently with the sole of your foot. Keep your right heel still and press down lightly, as if gently pushing a ball. Try counting three seconds after starting and gradually increasing pressure—the speed will stabilize. I like to practice in empty parking spaces—lightly press the accelerator until the tachometer stabilizes around 2000 RPM, then hold it. Don’t rush; try a few times to get the hang of it. While driving, pay attention to road conditions, like easing off before a red light. Manual transmission cars are a bit more complicated—you need to engage the clutch halfway while pressing the accelerator when starting, but don’t get too nervous. Mastering these techniques will make you a more confident driver.
Was this review help?
16
1
Share
Expand All
More Forum Discussions

How to Remove the Honda Lingpai Wiper?

The method for removing the Lingpai wiper is as follows: 1. Lift the wiper arm from the windshield. 2. Then press and hold the wiper lock pin to release it. 3. Finally, slide the wiper along the wiper arm to remove it. Maintenance methods for the Lingpai wiper: 1. Replace the wiper blade when it hardens. If the wiper works well during heavy rain but leaves uneven streaks when used in light rain, affecting visibility, this indicates the wiper blade has hardened. 2. Replace the wiper arm when the spring tension weakens. The wiper blade relies on the spring tension of the wiper arm to maintain close contact with the windshield. If the spring tension weakens, the wiper may lift due to strong wind pressure on the windshield at high speeds, especially noticeable with longer wipers, leaving parts of the glass uncleaned. This is commonly referred to as wiper lift during driving, and it is best to replace the wiper arm in such cases. 3. In some situations, such as when the wiper causes a foggy, water-beaded, streaky, or partially blurred windshield, this is due to oil film, dirt, or wax buildup. Simply cleaning the windshield and wiper blade will resolve the issue.
17
3
Share

What Causes Compressor Failure?

Compressor failure is caused by liquid slugging, oil shortage, and insufficient lubrication. Below is an analysis of compressor damage: 1. Liquid Slugging: A phenomenon where liquid refrigerant and lubricating oil are drawn into the compressor cylinder along with gas, damaging the suction valve plates. Reducing or preventing liquid from entering the cylinder can avoid liquid slugging, making it entirely preventable. 2. Oil Shortage and Insufficient Lubrication: The compressor is a high-speed, complex machine. Ensuring adequate lubrication of moving parts such as the crankshaft, bearings, connecting rods, and pistons is a basic requirement for maintaining normal operation.
3
5
Share

No Sound When Navigation is Connected to Car Bluetooth?

Phone call volume is not turned on. The volume of the car navigation system is not activated. Below is an analysis of why there is no sound when navigation is connected to car Bluetooth: 1. Solution: Go to the phone's Bluetooth settings, click the gear icon next to the paired device, and turn on "Call Audio" and "Media Audio." 2. Reason: This might be because when you got in the car, your phone's volume needed to be turned on again. Often, it automatically resets to 0, so naturally, there's no sound. Gradually increase the volume a little, and you'll know if there's sound.
1
4
Share

What number to call when a car is blocking the entrance?

Call 110 or 122, the traffic police hotline. Below is the analysis of making the call: 1. Procedure: Directly dial 110 or 122 to report to the police, provide the license plate number of the vehicle, and the traffic police will help you contact the owner to request moving the car. 2. Reason: By calling 110 or 122 and informing the operator that your car is blocked by a certain license plate number at a specific location, the traffic police will quickly contact the owner to move the vehicle. The traffic police indicate that upon receiving a request for vehicle removal, 110 will first notify the local traffic police department, which will then inform the squadron to contact the owner.
2
0
Share

Is the Honda Inspire's engine the same as the Accord's?

Honda Inspire shares the same engine with the Accord, both equipped with a 1.5T turbocharged engine, along with identical chassis and transmission. Below are some key details about the Inspire: 1. Stylistically, the Inspire leans more towards a sporty aesthetic compared to the Accord. This is evident from the bold grille design on both sides of the front fascia, featuring more expressive elements, while chrome accents further enhance its muscular appeal. 2. The side profile showcases sharp lines complemented by a fastback-style roofline and large stylish wheels, giving it a strong coupe-like presence. At the rear, the distinctive "boomerang"-shaped taillights offer excellent visual impact when illuminated. The most eye-catching feature is the dual exhaust setup, which adds a bold and dynamic touch. 3. The 8-inch freestanding LCD display on the dashboard adopts a physical button layout, offering a clean interface and responsive operation for easy usability. Additionally, the new model comes with built-in AutoNavi maps, enhancing the accuracy of its onboard navigation system.
13
4
Share

What is the fuel consumption per 100 kilometers for a 2.0T car?

2.0T version engines have a combined fuel consumption of around 11L per 100 kilometers. The following is an analysis of the combined fuel consumption for 2.0T engines per 100 kilometers: 1. Different models: The fuel consumption of 2.0T engines is influenced by factors such as the vehicle model, driving conditions, transmission technology, and driving habits, resulting in varying fuel consumption for each user. 2. Reasons: The BMW B48 2.0T version engine is developed based on BMW's B platform, representing a brand-new inline 4-cylinder engine. The Volkswagen EA888 2.0T version engine was introduced back in 2011, and the fourth-generation 2.0T version engine utilizes a dual-cycle switching system, with a compression ratio increased to 11.7:1 and a thermal efficiency as high as 38%.
17
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.