What are the symptoms of high-altitude sickness in cars?

1 Answers
Hunter
07/25/25 5:36am
The symptoms of high-altitude sickness in cars include the following: 1. Power reduction: Due to the low oxygen content at high altitudes, fuel combustion is incomplete, leading to a decrease in power. The extent of this reduction varies depending on the vehicle's condition and the road conditions. It is generally more noticeable when climbing slopes compared to driving on flat roads, and more pronounced in poorly maintained vehicles than in well-maintained ones. 2. Difficulty starting in some vehicles. 3. High-altitude vapor lock: Some pressurized fluids (such as brake fluid) containing trace amounts of air may not show issues at lower altitudes, but as the air pressure decreases at high altitudes, they can expand, directly affecting performance and even posing dangers. 4. Coolant overflow or boiling over. 5. Increased tire pressure: Normal tire pressure at lower altitudes will rise as altitude increases and air pressure decreases. If not adjusted in time, this increases the risk of tire blowouts. 6. Reduced fuel consumption in gasoline-powered cars: Air resistance at high altitudes is about 20% less than at lower altitudes.
Was this review help?
2
5
Share
More Forum Discussions

How Often Should Mercedes-Benz Brake Pads Be Replaced?

Mercedes-Benz brake pads are not replaced based on mileage. Generally, they need to be replaced when the brake warning light comes on. Additionally, you should check the thickness of the brake pads; if it is below 3mm, replacement is usually necessary. Here are the methods for inspecting brake pads: 1. Check the thickness: A new brake pad is typically about 1.5cm thick. As it wears down through friction, the thickness gradually decreases. When the visible thickness of the brake pad is reduced to about 1/3 of its original thickness (approximately 0.5cm), the owner should increase the frequency of self-inspection and be prepared to replace it. Some models, due to wheel design, do not allow for visual inspection, and the tire must be removed to check. 2. Listen for sounds: If a metallic scraping or squealing noise is heard when lightly applying the brakes (this could also be due to initial break-in of newly installed brake pads), the brake pads must be replaced immediately. 3. Feel the pedal response: If you notice that the brake pedal feels harder to press and requires deeper application to achieve the usual braking effect, or if the pedal position feels noticeably lower during emergency braking, it may indicate that the brake pads have lost most of their friction and must be replaced.
13
5
Share

Does the Mitsubishi Evo have great modification potential?

The Mitsubishi Evo has great modification potential. After modifications, this car can achieve significant improvements in both performance and appearance. From an exterior perspective, as a compact sedan, it is ideal for modifications, with the main areas being the engine hood and trunk lid. These can be modified using carbon fiber materials, which not only reduce the car's weight but also help the engine cool down faster during operation. More details are as follows: 1. Generally, modifying the car's exterior also involves modifying the interior. The interior is just as important as the exterior. The first step is to modify the steering wheel, followed by the paddle shifters, which can elevate the car's overall aesthetic. 2. For those seeking personalization, the car's roof can also be modified. A popular choice is the 'starry sky' roof lining, commonly seen in luxury models but rare in performance cars. Adding this feature to a performance car can enhance its uniqueness. 3. Additionally, a spoiler can be installed. Originally used on aircraft tails to improve stability, spoilers were later adapted for cars to enhance stability and reduce aerodynamic drag during driving.
16
3
Share

How to Remove the Tie Rod on a Ford Mondeo?

Ford Mondeo tie rod removal method is as follows: 1. Remove the tie rod dust cover: To prevent water from entering the steering gear, the tie rod is equipped with a dust cover. Use pliers and an opening tool to separate the dust cover from the steering gear. 2. Remove the tie rod-to-steering knuckle connecting bolt: Use a 16mm wrench to remove the bolt connecting the tie rod to the steering knuckle. If no special tools are available, you can use a hammer to tap the connection area to separate the tie rod from the steering knuckle. 3. Remove the tie rod-to-steering gear ball joint. 4. Install the new tie rod: Compare the new tie rod to ensure it matches the original part. First, attach one end of the tie rod to the steering gear and secure the locking plate on the steering gear. Then, install the bolt connecting it to the steering knuckle. 5. Secure the dust cover: If this step is not done properly, water entering the steering gear can cause steering noise. Apply sealant to both ends of the dust cover and secure it with zip ties. 6. Perform a wheel alignment: After replacing the tie rod, a wheel alignment is essential to adjust the data within the normal range. Otherwise, incorrect toe settings may lead to uneven tire wear.
7
2
Share

What engine does the Volkswagen Teramont have?

Volkswagen Teramont is equipped with two types of engines, which are: 1. The 2.0L turbocharged engine with the model EA888. Its advantages are superior power and technology, while the disadvantages are high maintenance costs and oil consumption issues. 2. The 2.5L turbocharged engine with the model EA390. Its advantages are compact size, strong power, and smooth operation. Extended content: The EA390-2.5T turbocharged engine has a rated power of 220kW/6000rpm, a maximum torque of 500Nm/2750~3500rpm, and adopts a DOHC double overhead camshaft structure with four valves per cylinder. It optimizes the intake and exhaust systems, features a dual-flow turbocharger, quickly exhausts emissions while increasing intake efficiency, and operates more efficiently than a standard turbocharger, promoting full combustion of fuel.
10
2
Share

Where is the low-pressure pipe port of Volvo S80 air conditioner?

Volvo S80 air conditioner low-pressure pipe port is located next to the computer on the right side of the vehicle. You need to open the decorative panel below the windshield wiper to see it. Here are some additional information: 1. Volvo S80 is the flagship model of Volvo, belonging to the mid-to-high-end Nordic luxury sedan. It competes with the BMW 5 Series and Mercedes-Benz E-Class. The S80 has a spacious cabin, comfortable seats with heating function, suitable for cold weather. The car has strong power, multiple engine options, and comprehensive configurations. 2. Volvo S80 is the safest car Volvo has ever produced. The high safety standards benefit from excellent design, sturdy body, and other features such as the SIPS system (Side Impact Protection System) with side airbags. In addition, the new S80 includes two world-leading innovations: IC (Inflatable Curtain) and WHIPS (Volvo Head Protection System).
6
2
Share

Where is the diagnostic connector located on the Peugeot 5008?

The diagnostic connector of the Peugeot 5008 is located inside the cabin. There is an OBD-labeled clip at the diagnostic connector; opening the clip reveals the diagnostic connector interface. The purpose of the car's diagnostic connector is: when the car malfunctions, the fault codes can be read through the car's OBD interface, and then the faults can be analyzed and cleared. Relevant information is as follows: 1. The OBD system continuously monitors whether the car's exhaust exceeds the standard during engine operation and will issue an alert immediately if it does. 2. Initially, the OBD interface was set up only to monitor the car's exhaust emissions, but in recent years, OBD has evolved through several generations, greatly enhancing its functions and roles.
17
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.