What are the symptoms of a faulty knock sensor in a car?

1 Answers
JayceMarie
07/30/25 5:07am
When the knock sensor in a car is damaged, the symptoms include: 1. Engine knocking occurs during operation. A faulty knock sensor can cause excessive ignition timing advance during engine operation, leading to engine knocking due to factors such as engine load, temperature, and fuel quality. 2. Decreased engine power, increased fuel consumption, accompanied by engine knocking. A damaged knock sensor affects the engine's load, resulting in higher fuel consumption and knocking sounds. Here is some information about the knock sensor in a car: 1. The knock sensor is an AC signal generator. It is used to detect the speed and position of the crankshaft, as well as vibrations or mechanical pressure. 2. The knock sensor is installed in various locations on the engine block or cylinders. When vibrations or knocking occur, it generates a small voltage peak; the more severe the knocking or vibration, the higher the peak produced by the knock sensor. A certain high frequency indicates knocking or pinging, and knock sensors are typically designed to measure frequencies in the range of 5 to 15 kHz.
Was this review help?
15
2
Share
More Forum Discussions

What is the function of the P gear?

P gear serves the purpose of parking. It utilizes a mechanical device to lock the rotating parts of the car, preventing the vehicle from moving. When the car needs to remain stationary for an extended period or before leaving the vehicle after parking, the handbrake should be engaged and the gear lever pushed into the "P" position. The introduction of car gears is as follows: P gear: Parking gear. The gear lever can only be moved into this position after the car has come to a complete stop, at which point the drive wheels are mechanically locked. R gear: Reverse gear. The gear lever can only be moved into this position after the car has completely stopped, enabling reverse driving. N gear: Neutral gear. After the gear lever is moved into this position, no power is transmitted to the wheels, and the wheels cannot utilize engine braking.
7
0
Share

Can You Still Drive If the Engine Guard Plate Falls Off?

You can still continue driving if the engine guard plate falls off. This situation is mainly caused by the engine guard plate not being securely fixed. It is recommended to go to a repair shop to have the engine guard plate refixed. This is not a major issue, and you can continue driving after securing it properly. More information about engine guard plates is as follows: Function: The engine guard plate is very important for a car. Its main role is to effectively protect the cleanliness inside the engine compartment and prevent water, mud, and other debris from entering the engine compartment. It also effectively prevents stones and hard objects kicked up by the tires during driving from hitting the engine. Introduction: The front end of the car engine guard plate has two hooks, so it won't fall off even if the screws loosen. If the engine guard plate falls off, it should be reinstalled promptly. Guard plates are vehicle-specific, and manufacturers provide matching screws. The vehicle needs to be lifted, and the guard plate should be installed according to the manufacturer's specifications.
19
1
Share

What are the reasons for an electric vehicle suddenly not moving?

Possible reasons for an electric vehicle suddenly not moving are as follows: Controller damage: If the controller of the electric vehicle is damaged, it may cause the wheels to stop turning even when there is power. Solution: Check if there is a burnt smell from the controller. If it is indeed damaged, a new controller needs to be replaced. Motor failure: If the motor of the electric vehicle malfunctions, such as poor contact of the motor carbon brushes, it can also cause the vehicle to have power but not move. Additionally, motor wear and damage can lead to the same issue. Solution: Repair the motor or replace it with a new one.
8
3
Share

What is the Impact of Tire Performance on Vehicle Driving?

The impact of tire performance on vehicle driving lies in support and handling, with specific details as follows: Support Function: Supports the total mass of the vehicle and withstands various forces from the road surface, including vertical reaction forces, lateral reaction forces, and tangential reaction forces. Absorbs and mitigates part of the impacts and vibrations encountered during driving, ensuring the vehicle has good ride comfort and smooth driving. Enhancing Handling: Ensures good adhesion between the tire and the road surface to improve the vehicle's dynamic performance, maneuverability, and off-road capability. The structure and performance of the tire itself also directly affect the vehicle's safety inspection and economy.
2
2
Share

Why does the Audi A3 shake at idle when waiting at a red light?

Audi A3 shaking at idle when waiting at a red light may be caused by engine intake pipe leakage, fuel system blockage or malfunction, or idle control valve failure. Engine intake pipe leakage: The intake system contains many intake manifolds and various valves. If there is a leak, it can cause the concentration of the air-fuel mixture in the intake manifold to become too high or too low, leading to intermittent engine shaking or weak idle. Fuel system blockage or malfunction: Blockages in areas such as the fuel tank vent hole or certain fuel lines can prevent the engine from receiving the appropriate amount of fuel during idle, resulting in a lean air-fuel mixture, weakened engine power output, and idle shaking. Idle control valve failure: The idle operation of fuel-injected engines is mostly controlled by the idle control valve. The ECU adjusts the opening of the idle control valve based on signals such as engine speed, temperature, and throttle position to maintain stable engine idle. If the valve fails, it can cause uneven air distribution, fluctuating idle power, and vehicle shaking.
18
1
Share

How Many Types of Brake Water Spray Devices Are There?

1.5-2 atmospheric pressures are sufficient. Brake system maintenance can be carried out from the following aspects: 1. High-temperature protection for brake pads: Prevent corrosion in the brake system, avoid brake pad seizure due to high temperatures, eliminate brake pad squealing, and maintain good long-lasting lubrication. Products containing ceramic components that can withstand temperatures above 1400°C are required. Therefore, regularly check the thickness of the brake pads or brake shoes. Replace them immediately when their thickness approaches or falls below the manufacturer's specified minimum thickness. 2. Brake caliper lubrication maintenance: Lubricate the moving shafts and rubber cups of the brake calipers, keep the caliper bushings soft, and extend the caliper's service life. Fully synthetic brake caliper lubricant should be used. 3. Brake disc cleaning: Quickly clean oil stains, dirt, and friction dust from brake discs, brake drums, and any other parts to maintain good heat dissipation of the brake discs; eliminate harsh brake noises and promote even braking. 4. Brake fluid replacement: Brake fluid has water-absorbing properties. If not replaced for a long time, it can corrode the braking system, posing a hazard to driving. Generally, it is recommended that owners replace the brake fluid every 20,000 kilometers, mainly to ensure the cleanliness of the brake fluid. 5. Anti-rust lubrication for tire bolts, brake discs, and wheel rim contact surfaces: Prevent corrosion and bolt seizure due to heat, facilitate disassembly, and use products containing aluminum components that can withstand temperatures above 1100°C to ensure contact area with the brake pads and improve braking force.
11
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.