What are the symptoms of a faulty diesel injector?

1 Answers
RhettLee
07/29/25 1:03pm
Diesel engine injector damage can cause noticeable power loss, black smoke from the exhaust pipe, increased engine noise, and sometimes a distinct "click, click, click" sound from the engine. The injector is a crucial component of diesel internal combustion engines, and its atomization level determines fuel consumption and engine power output. Good injector atomization ensures that vehicle fuel is fully converted into kinetic energy, maximizing power output. Here are methods to avoid injector damage: 1. Refueling: Always refuel at reputable, large gas stations. 2. Maintenance: Replace the diesel filter promptly. The diesel filter is the last line of defense for protecting the injector, plunger, and other fuel system components, so always purchase filters from reputable manufacturers and avoid cheap, inferior products.
Was this review help?
4
5
Share
More Forum Discussions

How to remove the horn of Kia K2?

There are two methods to remove the horn of Kia K2. First, you can see the screws installed on the side. There are clips inside, and you can pry the clips by feeling with your hand. Second, there are two small holes about the size of mung beans on both sides of the black plastic cover under the steering wheel. Insert a small flat-head screwdriver into the holes, and with a little feeling or using a flashlight, twist it to pry open the wire spring buckle, and then the cover in the middle of the steering wheel can be removed. Method to remove the horn clock spring of Kia K2: 1. Align the wheels and steering wheel, then disconnect the negative terminal of the battery. 2. Use tools to remove the steering wheel assembly and the steering wheel airbag. 3. Remove the headlight switch trim panel, then remove the airbag clock spring, install the new airbag clock spring and plug in the connector. Then turn the airbag clock spring to the end and rotate it back two and a half turns. Finally, reinstall the steering wheel and steering wheel airbag, and reconnect the negative terminal of the battery.
14
3
Share

What is the reason for no display when pressing the auto hold button in Leopaard CS9?

It is very likely that there is a problem with the electronic parking brake, or it could be caused by worn brake pads, an issue with the electronic system, or a problem with the battery power supply. This must be checked at a repair shop using a decoder to read the fault codes, and then repaired according to the fault codes. Below are the solutions for electronic parking brake failures: 1. Reset the electronic parking brake by turning on the car key, pressing the foot brake, then pressing down the electronic parking brake for 5 seconds and pulling it up for another 5 seconds. This will initialize and reset the electronic parking brake. 2. The parking brake, commonly referred to as the handbrake, is usually installed in the driver's right-hand position for easy use. 3. The function of the parking brake is to stabilize the vehicle after it has stopped, preventing accidents caused by rolling on inclined roads. 4. Some automatic transmission models on the market have a foot brake designed on the outside of the driver's left foot with the same function as the handbrake, and some advanced models are also equipped with an electronic parking brake system.
16
3
Share

How to deal with asphalt spots on the car?

There are the following methods to deal with asphalt spots on the car: 1. To remove these asphalt spots from the car body, car wax must be applied. The oil content in the wax can dissolve the tar in the asphalt. By repeatedly applying car wax, the tar adhering to the car body can be removed. After wiping it off, use a clean cotton cloth to wipe again, which can thoroughly remove any residual tar stains on the car body. 2. Do not rush to rinse or grind, as it may affect the car's paint surface. First, use high-pressure water to rinse the car body for initial cleaning. If asphalt or other dirt remains, you can rinse these local areas again and then wash them with soapy water.
2
0
Share

What are the wiper size and interface type for the Volkswagen Passat?

The wiper size for the Volkswagen Passat is 24+19 inches. There is no fixed replacement cycle; replace them promptly if there is abnormal noise or poor wiping performance. Below are the steps to replace the wiper blades for the Volkswagen Passat: 1. After turning off the vehicle, do not remove the key immediately. Within three seconds, move the wiper lever, and the wipers will enter maintenance mode. 2. Push the wiper firmly toward the front of the vehicle until it locks into place. Press the silver button on the wiper arm, hold the wiper blade, and gently pull it outward to remove the old rubber strip. 3. Release the two clips and remove the old rubber strip. (Be gentle when removing the clips on both sides and the middle connecting device.) 4. When installing the new rubber strip, ensure the two metal pieces are staggered and inserted into the first groove. The process is slightly tedious and requires patience—install one side first, then the other. 5. After successful installation, follow the reverse steps of the removal process to complete the wiper installation.
3
3
Share

Where is the engine number of BMW 320 located?

The engine number of BMW 320 is located on the driver's side wall of the engine compartment, where there is a nameplate engraved with the engine number. The engine number includes information such as the engine model, production time, and origin code, and is unique, with each engine having a specific number. The engine number is an important piece of vehicle information, facilitating the management of the vehicle's engine by the engine manufacturer and vehicle management authorities. The BMW 320 is a car under the BMW brand, with dimensions of 4719mm in length, 1827mm in width, and 1459mm in height, and a wheelbase of 2851mm. The car is equipped with a 12.3-inch programmable full LCD instrument panel, a 10.25-inch touch-sensitive central control display, and a full-color head-up display system that allows for three-screen linkage.
7
4
Share

Is it necessary to clean the car throttle body?

Cleaning the car throttle body is indeed necessary, as the responsiveness of the car's acceleration is closely related to the cleanliness of the throttle body. Cleaning the throttle body can even improve efficiency and save fuel. The steps for cleaning the throttle body are as follows: 1. First, disconnect the wiring harness connector next to the throttle body, use a hex screwdriver to remove the fixing screws, and then take off the throttle body. 2. Cover the air intake to prevent debris from falling into the engine. 3. Spray cleaning agent on the dirt. Be careful not to spray the cleaning agent outside the throttle body, avoid forcefully prying the internal throttle body, and prevent damage to the adjacent throttle motor. 4. Finally, let it dry naturally. It is best not to wipe it with a cloth, as this can easily remove the surface lubricating coating. 5. After reinstalling the throttle body, disconnect the power and restart or redo the throttle body matching.
7
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.