What are the steps to use cruise control?

1 Answers
VanValeria
07/29/25 12:16pm
The steps to use cruise control are: 1. Press the power button to activate the cruise control system; 2. Increase the vehicle speed to the desired level and press the set button, then release the accelerator with your right foot to lock the speed at the current rate; 3. Use the res (+) and set (-) buttons to fine-tune the speed; 4. Press the brake, cancel button, or power button to deactivate cruise control; 5. If cruise control is canceled by pressing the brake or cancel button, you can press the res button to resume the previous cruise control speed. When the cruise control function is activated, you can press the accelerator to increase the speed to or above the lower limit of the cruise control speed. Once the cruise control function is confirmed to be active, the engine will automatically supply fuel to meet the power requirements for the current speed.
Was this review help?
12
3
Share
More Forum Discussions

Is the Jeep Wrangler Suitable for Family Use?

jeep Wrangler is not suitable for family use, but rather for those who enjoy off-roading. Taking the 2021 Wrangler two-door version as an example, it belongs to the mid-size SUV category with the following dimensions: length 4334mm, width 1894mm, height 1839mm, wheelbase 2459mm, fuel tank capacity 70l, and curb weight 1843kg. The 2021 Wrangler two-door version is equipped with a 2.0T turbocharged engine, delivering a maximum horsepower of 266PS, maximum power of 195.4kW, and maximum power speed of 5000rpm. It is paired with an 8-speed automatic transmission.
7
0
Share

What Causes Abnormal Noise When Accelerating a Motorcycle?

Abnormal noise when accelerating a motorcycle is usually caused by excessive valve clearance or loose components. Here are specific solutions: 1. Excessive valve clearance: The noise during acceleration is caused by excessive valve clearance, which can be resolved by readjusting the valve clearance. A "clanking" sound under load during acceleration may result from poor-quality gasoline or a lean air-fuel mixture due to insufficient fuel supply from the carburetor. This can be fixed by using standard gasoline and cleaning the carburetor. 2. Loose components: If the noise is due to loose parts, it is advisable to have the motorcycle inspected and repaired at a service center to prevent minor issues from escalating into major accidents, thereby reducing potential economic losses.
8
3
Share

What is the difference between Hankook ex+ and ex?

Here is an introduction to the differences between Hankook ex+ and ex: 1. Price: Hankook ex+ is relatively more expensive and is one of the top performers in the automotive tire market, offering higher cost performance compared to lower-priced products on the market; Hankook ex is relatively cheaper than ex+, but still provides better cost performance than lower-priced products available. 2. Performance: Hankook ex+ offers superior performance, greater practicality, and excels in handling and grip; Hankook ex has slightly lower performance compared to ex+, and is not as good in aspects like handling and grip.
9
4
Share

What does it mean when the TC light comes on in the Buick GL8?

When the TC light comes on in the Buick GL8, it indicates that the engine control module has detected a fault in the traction control system. The reasons for the TC light coming on are: 1. Solenoid valve failure; 2. Dirty engine oil clogging the solenoid valve filter screen; 3. Wear of the actuator gear and impeller causing oil pressure leakage; 4. Dirty throttle body. The Buick GL8 is a 5-door, 7-seater MPV with body dimensions of 5238mm in length, 1878mm in width, 1776mm in height, and a wheelbase of 3088mm. It is equipped with a 2.0T turbocharged engine, delivering a maximum power of 174kW and a maximum torque of 350Nm, paired with a 9-speed automatic transmission.
20
3
Share

What is the method for a car to pass over a speed bump?

Car passing over a speed bump method is: before passing over the speed bump, reduce the speed, and pass slowly with both wheels vertically. This method allows both left and right wheels to contract simultaneously, and the force from the ground is equally shared by the springs and shock absorbers of both wheels. Even force distribution can minimize damage to the car. The wrong practices for a car passing over a speed bump are: 1. Passing over the speed bump with only one side of the tires; 2. Passing over the speed bump at high speed; 3. Passing over the speed bump diagonally. Speed bumps, also known as speed humps, are traffic safety devices installed on roads to reduce the speed of motor vehicles and non-motor vehicles.
4
2
Share

What is the 0-100 km/h acceleration time for the Mustang 2.3T?

The Mustang 2.3T accelerates from 0 to 100 km/h in 6 seconds, which is a direct reflection of the car's power. The Mustang 2.3T is a 2-door, 4-seater hardtop sports car with the following dimensions: length 4794mm, width 1916mm, height 1391mm, wheelbase 2720mm, fuel tank capacity 58.9 liters, and curb weight 1702kg. It is equipped with a turbocharged engine that delivers a maximum power of 220kW at 5400 rpm and a maximum torque of 434Nm at 3000 rpm.
17
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.