What are the steps to clear the anti-skid warning light?

1 Answers
DawsonLynn
07/29/25 8:47pm
Steps to clear the anti-skid warning light: Restart the engine and briefly press the ESP OFF button on the vehicle. The main reasons for the anti-skid warning light to illuminate are as follows: 1. Accidentally pressing the ESP OFF button; 2. Loose or faulty sensor connectors; 3. Short circuit in the wiring or related fuse blown; 5. Software issues causing poor signal transmission; 6. ABS pump failure. Below is an introduction to the anti-skid system: 1. Composition: The anti-skid system, also known as the vehicle stability system, is a chassis braking technology developed based on the anti-lock braking system (ABS). It mainly consists of a control unit, steering sensor, wheel speed sensor, skid sensor, lateral acceleration sensor, etc.; 2. Function: It enables automatic vehicle safety control, effectively improving driving stability and safety during dynamic conditions such as braking, acceleration, and steering.
Was this review help?
16
4
Share
More Forum Discussions

What causes high idle speed in a hot Santana?

The reason for high idle speed in a hot Santana is due to the idle switch not closing and the idle contacts being disconnected. The solutions are as follows: 1. Check the throttle opening. If the basic idle speed is too high, inspect the vacuum sealing of the system, especially the sealing of the vacuum tube, PCV valve, and related parts of the crankcase. 2. Check the engine load signal. If the idle control valve opening is too large, verify whether the engine load signals are normal, such as the air conditioning signal, battery voltage, and the temperature value of the water temperature sensor. 3. Check the vacuum degree of the intake manifold. During normal engine idle conditions, the vacuum degree of the intake manifold should be 57~71kPa. If the vacuum degree is too low, it will cause abnormal pressure signals in the engine intake system, leading the engine computer to mistakenly assume an increased load and thus raise the idle speed.
8
2
Share

Can the Audi A4L lock automatically?

Audi A4L can lock automatically. When the vehicle speed reaches the preset speed by the computer, the lock button on the door will automatically press down to prevent accidentally opening the door. The function of automatic locking: Automatic locking can effectively prevent the door from being opened accidentally, and it also has anti-theft features. The doors lock quickly after driving, preventing door-pull robberies during traffic jams or at red lights, providing a certain level of security. The disadvantages of automatic locking: There are also some drawbacks, such as affecting escape in emergency situations. If all occupants in the car become unconscious, rescuers outside may waste more time trying to open the doors.
2
0
Share

What is the model number of the Subaru Outback's low beam headlight?

Subaru Outback's low beam headlight model is D2S (original xenon lamp), high beam: 9005 (HB3). Introduction to high beam: The intensity of the light is adjusted based on the distance of the filament. The high beam is at its focal point, emitting light that is parallel and more concentrated, with greater brightness, capable of illuminating distant and high objects. Introduction to low beam: The low beam is outside its focal point, between 1 to 2 times the focal distance, emitting light in a divergent state, capable of illuminating a larger area of nearby objects. The low beam's illumination distance is approximately 30-40 meters.
7
1
Share

What is the top speed of the Honda CBF190TR?

Honda CB190R has a maximum speed of 122 kilometers per hour. The top speed of Honda CB190R is influenced by the following factors: Engine power: There are many factors that affect the maximum speed of a car, such as the power of the car's engine, the maximum torque of the engine, the speed at maximum torque, the transmission ratio of the drivetrain, driving resistance, etc. Main influencing factors: The maximum speed is measured on a flat and windless road surface with zero acceleration, so the gradient resistance and acceleration resistance are zero. Therefore, the main resistance factors affecting the maximum speed are air resistance and rolling resistance.
15
3
Share

At what tire pressure does the Civic trigger an alarm?

The Honda Civic's tire pressure is around 2.2-2.5 bar. The 10th-generation Civic is equipped with a tire pressure monitoring system. Unlike directly measuring the tire pressure of each tire, this system monitors the vehicle and compares the rolling radius and rotational characteristics of each wheel and tire. If the tire pressure falls outside this range, an alarm will be triggered. Civic parameters: Fuel consumption: 5.0-6.4L, Body structure: 4-door 5-seat sedan, Engine: 1.0T/1.5T, Transmission: 6-speed manual/CVT, Drive type: Front-wheel drive, Fuel type: Gasoline. Hazards of too high or too low tire pressure: For tires, the pressure should neither be too high nor too low. Excessive tire pressure reduces the contact area between the tire and the ground, leading to poor grip, which affects the car's handling and driving stability. Insufficient tire pressure can cause wave-like deformation during high-speed driving, shortening the tire's lifespan and increasing the risk of a blowout. Introduction to standard tire pressure: According to the international GBT2978-2008 standard, the recommended tire pressures for different tires are as follows: Standard tires: 2.4-2.5 bar; Reinforced tires: 2.8-2.9 bar; Maximum pressure: Should not exceed 3.5 bar.
19
5
Share

Where is the triangular warning sign placed in the Audi Q5L?

The triangular warning sign in the Audi Q5L is located in the trunk. Open the cover, and there is a small switch in the middle of the cover. Pull it down to see the warning sign. Introduction to the triangular warning sign: The triangular warning sign, accurately known as the motor vehicle triangular warning sign, is a passive reflector made of plastic reflective material. When a driver encounters a sudden breakdown requiring parking for repair or an accidental collision on the road, the reflective properties of the triangular warning sign can alert other vehicles to avoid it, thereby preventing secondary accidents. Standards for the triangular warning sign: The latest national standard for triangular warning signs is "GB19151-2003 Motor Vehicle Triangular Warning Sign." This standard specifies the technical requirements, test methods, and inspection rules for triangular warning signs.
17
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.