What are the steps for tire rotation?

1 Answers
LeCarlos
07/30/25 4:02am
1. Lift the vehicle to about 10cm above the ground to test stability. After ensuring safety, raise the vehicle to the appropriate position. 2. Remove the tires from the vehicle. 3. Perform dynamic balancing on all four tires. 4. Carry out the tire rotation. 5. Use a torque wrench to tighten the wheel bolts according to the specified sequence and torque requirements. 6. Lower the vehicle and conclude the process. Wheel alignment is required under the following circumstances: 1. During normal driving, with proper tire pressure, the vehicle doesn't drive straight even when the steering wheel is centered. 2. The vehicle feels unstable when taking turns. 3. Upon inspecting the tires, uneven wear patterns are observed.
Was this review help?
2
0
Share
More Forum Discussions

Why Does My Car Smell Strongly of Gasoline When Starting?

The reasons for a strong gasoline smell when starting a car are: 1. Insufficient air intake through the throttle body, leading to incorrect air flow information; 2. Excessive carbon buildup in the cylinder combustion chamber and pistons, resulting in insufficient cylinder pressure; 3. Too much carbon deposits inside the engine, causing poor atomization of the air-fuel mixture; 4. Gasoline pipe leakage, forming sludge at pipe connections, with the odor entering the cabin through the air conditioning system. Solutions for addressing a strong gasoline smell when starting the car include: 1. Replace the rubber hoses of the gasoline vapor canister; 2. Tighten or repair gasoline pipe connections; 3. Repair or reinstall the fuel pump; 4. Avoid overfilling the fuel tank.
6
4
Share

What is the ground clearance of the Toyota RAV4?

The ground clearance of the Toyota RAV4 is 193 millimeters. The function of the chassis is to support and install the car engine and its various component assemblies, forming the overall shape of the car, receiving the power generated by the engine, and ensuring normal driving when the car is in motion. The Toyota RAV4 is a compact 5-door, 5-seat SUV with body dimensions of 4600 mm in length, 1855 mm in width, 1720 mm in height, and a wheelbase of 2660 mm. The Toyota RAV4 is equipped with a 2.4L naturally aspirated engine and a 4-speed automatic transmission, with a maximum power of 125 kW at 6000 rpm and a maximum torque of 224 Nm at 4000 rpm.
4
1
Share

What is the body weight of the Volkswagen Lavida?

The body weight of the Volkswagen Lavida is 1.2 tons. The Lavida is produced by Shanghai Volkswagen, with dimensions of 4600mm in length, 1700mm in width, and 1500mm in height, and a wheelbase of 2610mm. In terms of color scheme, the Lavida inherits the traditional two-tone interior design of Volkswagen models in China, featuring a darker upper section and a lighter lower section. However, between these two sections, it incorporates a wood-grain trim that blends with the center console, inspired by the design style of Japanese mid-size cars. Exterior-wise, the front fascia of the Lavida differs significantly from previous Volkswagen A-segment models, particularly with its unique teardrop-shaped headlights. The traditional Volkswagen grille and U-shaped front design are also prominently featured and carried forward in the Lavida.
2
1
Share

Strong Jerking Sensation When Shifting from Second to Third Gear in Automatic Transmission

Introduction to the causes of strong jerking sensation when shifting from second to third gear in automatic transmission: Transmission issues: The jerking sensation during gear shifts in an automatic transmission can be caused by dirty transmission fluid, oil pump pressure leakage, or internal clutch slippage. A detailed analysis of the transmission's data stream is required to pinpoint the exact cause. Shift solenoid valve problems: If the vehicle has reached 2 years or 60,000 kilometers, it is advisable to replace the transmission fluid. If the issue persists after replacement, the shift solenoid valves for second and third gears should be inspected. Engine oil passage blockage: The engine's power output, which affects the smoothness of gear shifts, is determined by the ignition, air intake, and fuel injectors. A decrease in air intake, weaker ignition, or reduced fuel injection can lead to insufficient power, resulting in a jerking sensation.
9
5
Share

Do I need to wait for the traffic light when driving to the right front?

If it is a dedicated right-turn lane, you generally do not need to wait for the traffic light in this situation. Below is relevant information about traffic lights: Introduction: Traffic lights are signals that direct traffic flow. Classification: Traffic lights are divided into motor vehicle signals, non-motor vehicle signals, pedestrian crossing signals, directional indicator lights (arrow signals), lane signals, flashing warning signals, and railway crossing signals. Light Colors: Initially, there were only red and green colors. Later, after improvements, a yellow light was added. The red light means stop, the yellow light means prepare, and the green light means go. The reason these three colors are used as traffic signals is related to human visual structure and psychological response.
4
3
Share

Is pulling up the left turn signal or the right turn signal?

Turning on the right turn signal is done by pulling up. Below is relevant information about car turn signals: Introduction: The turn signal is an important indicator light that is activated when the vehicle is turning to alert surrounding vehicles and pedestrians. The turn signal bulb uses a xenon tube, controlled by a single-chip microcomputer circuit, working continuously with alternating left and right flashes. The turn signal employs a flasher to achieve the blinking effect. Timing is crucial when activating the turn signal; it should be turned on approximately 100 meters before the turn. If changing lanes, it should be activated even earlier. Turning it on too early may give the impression of "forgetting to turn off the signal" to the following vehicle, while turning it on too late may cause accidents due to insufficient reaction time for the following vehicle or pedestrians. Classification: Turn signals use flashers to achieve the blinking effect. They can mainly be divided into three types: resistance wire type, capacitor type, and electronic type.
13
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.