What are the steps for driving a car?

1 Answers
VanMalia
07/30/25 6:35am
The basic steps for driving a car are: 1. Walk around the car to check for any special circumstances before getting in; 2. After entering the car, adjust the seat position and the angles of the left and right rearview mirrors according to your comfort; 3. Fasten the seatbelt after adjustments are made; 4. Fully depress the clutch and brake, then turn on the left turn signal; 5. Shift into first gear and start slowly, ensuring there are no vehicles or pedestrians within a certain distance behind before entering the traffic lane. Prohibited actions when starting the car: 1. Avoid unstable starts; 2. Avoid selecting an inappropriate gear for starting; 3. Avoid improper coordination of the clutch pedal, accelerator pedal, and brake pedal when starting; 4. Avoid leaving the left foot on the clutch pedal after starting or forgetting to release the parking brake lever when starting; 5. Avoid starting without clearly observing the surroundings; 6. Avoid starting the car with faults, insufficient engine oil or coolant, or driving without complete documentation.
Was this review help?
8
1
Share
More Forum Discussions

How many painted surfaces does a car have in total?

A car has a total of 13 painted surfaces. Below is a partial introduction about painted surfaces: 1. Distribution of painted surfaces: The exterior of a car has 13 painted surfaces, which are: the front and rear bumpers, the left and right front fenders, the two doors on the left side, the two doors on the right side, the left and right rear fenders, the front hood, the rear trunk lid, and the roof of the vehicle. 2. Paint material: Automotive paint generally consists of four basic components: film-forming substances (resins), pigments (including extender pigments), solvents, and additives. The film-forming substance is the main component of the paint, whose function is to keep the pigments bright, make them sturdy and durable, and allow them to adhere to the surface of the object. It is the substance that determines the type of paint.
19
0
Share

What is the issue when PRE-SAFE stops functioning

PRE-SAFE stops functioning under the following circumstances: 1. Normal situation: If PRE-SAFE stops functioning under normal circumstances, it does not affect the vehicle's operation. The driver can restore normal function by turning off the engine and restarting it. 2. Sensor malfunction: In special cases where it cannot be activated, it may be due to a sensor malfunction. It is recommended to take the vehicle to a 4S shop for inspection and check if the car radar needs cleaning; it is also possible that the camera sensor was damaged during car washing. 3. Safety protection device turned off: Additionally, PRE-SAFE stopping functioning could be due to the vehicle's safety protection device being turned off, meaning the passenger airbag switch is deactivated. The owner can go to a service station for assistance or manually turn on the passenger airbag themselves, with the switch located on the passenger side. If none of these issues are present, the owner can choose to upgrade the computer system and then clear the fault code.
6
1
Share

What to do if ETC was scanned when entering but not when exiting the highway?

Here are the solutions if the ETC card was not scanned when exiting the highway: 1. Contact the bank. 2. Contact the toll station and highway company. 3. Call the highway service hotline. If you choose to evade the toll when exiting the highway without ETC deduction, you will be blacklisted by ETC and prohibited from using highways nationwide. You will be charged the maximum distance fee for the entire highway. Therefore, you should follow the instructions of the toll station staff to the MTC or manual lane and pay the toll by swiping the card or cash to proceed. Below is an introduction to ETC: ETC, also known as the Electronic Toll Collection system, is a road toll method specifically designed for toll roads. It is commonly used on highways, toll bridges or tunnels, and some sections of urban roads to alleviate traffic congestion in cities.
8
2
Share

Can Turbocharged Engines Be Shut Down Immediately Now?

Now turbocharged engines cannot be shut down immediately. Here are the specific reasons why turbocharged engines cannot be shut down immediately now: 1. Unable to dissipate heat: When cooling is interrupted, the car cannot rotate, and the engine bearings will continue to spin at high speed, causing certain bearing damage. 2. Protecting the turbocharger: The turbocharger in the car serves to enhance lubrication. When the engine is turned off during high-speed driving, its internal operation stops, but due to inertia, it continues to move at high speed. At this point, the lack of lubrication can easily cause damage. To protect it, it is necessary to wait for a while after parking before shutting down the engine, which can effectively reduce damage to the turbocharger.
7
0
Share

Why is the Buick Excelle's reversing radar not beeping?

Buick Excelle's reversing radar not beeping is most likely an issue with the buzzer. Here are the specific details:1. Introduction: The full name of the reversing radar is "reverse anti-collision radar", also known as "parking assist device". It is a safety auxiliary device for parking or reversing, consisting of ultrasonic sensors (commonly known as probes), a controller, and a display (or buzzer).2. Function: When reversing, it helps the driver "see" things that are not visible in the rearview mirror, informing the driver of the surrounding obstacles through sound or more intuitive display. It relieves the driver from the trouble of looking around when parking, reversing, and starting the vehicle, and helps the driver eliminate blind spots and blurred vision defects, improving driving safety.
14
0
Share

How many liters of engine oil should be added to the T-Roc?

The T-Roc requires 4 liters of engine oil. Oil dipstick markings: There are two markings on the oil dipstick: one is the maximum level, and the other is the minimum level. The normal oil level should not be above the maximum level or below the minimum level; it should be between these two markings. Method for checking the oil level: After adding the engine oil, start the vehicle and then turn it off. Wait for 3 minutes before checking the oil level. This is because when changing the engine oil, the oil filter also needs to be replaced. The new oil filter initially contains no oil, and after starting the vehicle, oil will flow into the filter. Waiting for 3 minutes allows the oil to settle into the oil pan, ensuring a more accurate reading. Note that you should not check the oil level on a slope, as the vehicle's tilt will cause the oil in the pan to tilt as well, leading to an inaccurate measurement.
9
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.