What are the steps for changing engine oil?

2 Answers
LeDaniella
07/25/25 12:02pm
The steps for changing engine oil are as follows: 1. After driving the car onto the lift, turn off the engine, use the lift to raise the vehicle, engage the handbrake, and secure the front wheels with wooden wedges; 2. Place an old oil container under the oil pan, locate the oil pan drain bolt, and slowly loosen the drain bolt, being careful not to come into contact with the hot oil; 3. Move the oil container under the oil filter, use an oil filter wrench to loosen the filter, then unscrew it by hand. If the filter is still hot, remember to wear gloves; 4. Refer to the user manual to select the appropriate oil filter; 5. Apply new oil to the gasket of the new filter. If the filter is installed vertically, you can pour some new oil into the filter to reduce dry friction during the next engine start; 6. Pour the new oil into the oil pan, following the instructions in the user manual. Use a funnel to prevent spilling oil on the outside of the engine.
Was this review help?
4
5
Share
DiKylie
08/11/25 8:12pm
Every time I change the car oil myself, I follow the standard procedure to ensure safety and effectiveness. Before starting the whole process, the car must be parked and turned off, with the handbrake pulled tight to prevent sliding. Prepare tools including a jack or ramps to lift the car body, and wear thick gloves to prevent burns. Locate the drain plug under the chassis, slowly loosen it with a wrench to let the old oil flow into the oil pan, being careful not to splash the hot oil on yourself. After the oil has drained, remove the old oil filter, apply new oil to the seal of the new filter, and tighten it to prevent leaks. Clean the drain hole surface and tighten the bolt, then pour in the new oil using a funnel to avoid spills. While pouring, check the dipstick to ensure the oil level is between the middle marks and does not exceed the upper limit. Start the engine and run it for five minutes to check for leaks underneath. Dispose of the used oil at a repair shop for environmentally friendly recycling. It is recommended to change the oil every 5,000 kilometers to keep the engine clean and extend its lifespan. The whole process takes about an hour but can save a lot on maintenance costs and also teach you some skills.
Was this review help?
12
4
Share
Expand All
More Forum Discussions

What are the features of CarLife in cars?

CarLife is a car networking solution launched by Baidu at the 'Connected Cars, Smart and Measured' strategy conference on January 27, 2015. On the car's end, whether it's Linux, QNX, or Android, Baidu CarLife can be well adapted. The following is a detailed introduction to the main features of CarLife: 1. Map Navigation: Voice input, intelligent broadcast, automotive-grade HMI interface design, and connection to car data can achieve high-precision navigation. 2. Music: Play local music, listen to online music or radio, and support third-party service integration. 3. Phone: Make calls, answer incoming calls, synchronize and view mobile phone contacts, and check call history.
5
0
Share

How to Use the Bora's Air Conditioning?

The method for using the Bora's air conditioning varies depending on the situation: 1. Manual air conditioning: Set the air circulation mode to internal circulation, adjust the temperature using the temperature control buttons, and press the A or C button to turn off the air conditioning. 2. Automatic air conditioning: Press the AUTO button and adjust the temperature. Types of car air conditioning can be categorized based on different criteria: 1. By driving method: Independent and non-independent. 2. By performance: Single-function and combined heating/cooling. 3. By control method: Manual and electrically controlled pneumatic adjustment. 4. By adjustment method: Fully automatic adjustment and microcomputer-controlled fully automatic adjustment.
16
0
Share

Why Does the Car Shake at Idle Speed?

Reasons why the car shakes at idle speed: 1. The throttle is dirty or the fuel injector has excessive carbon deposits. 2. Issues with the ignition system. At this time, it is necessary to check the working condition of the spark plugs, high-voltage wires, and ignition coils. Poor performance of the ignition system or bad spark plug firing can also cause such faults. 3. Unstable oil pressure. If you have already cleaned the engine carbon deposits, cleaned the throttle, replaced the oil pads and spark plugs, but still find the car shaking at idle speed, it is recommended to go to a 4S shop to check whether the fuel supply pressure and the intake pressure sensor are normal. 4. Aging of the engine mounts.
2
2
Share

How to use Mazda i-stop?

To use Mazda i-stop, press and hold the i-stop button for more than 2 seconds to toggle it on or off. The i-stop button is located on the lower left panel of the steering wheel. When i-stop is activated, the dashboard will display it in green; when deactivated, it will show in orange. The conditions for i-stop activation are: 1. The engine is fully warmed up and the hood is closed; 2. All doors and windows are closed; 3. The vehicle is stationary and the battery is in good condition; 4. The driver's seatbelt is fastened; 5. The windshield defroster is turned off; 6. The air conditioning is on; 7. The air conditioning temperature is set to match the interior temperature.
19
5
Share

What to Do When the Seat Belt Gets Stuck?

If the seat belt gets stuck, you can try to gently retract and extend it to restore its function. In case of a mechanical failure, it is recommended to seek professional repair. Improper use of a stuck seat belt can cause deformation, making it prone to jamming at the entry and exit points. This situation is relatively simple to resolve; usually, straightening the seat belt and slowly pulling it out will suffice. A seat belt is a safety device used in equipment, such as aircraft or during high-altitude work and performances, to ensure safety. The main materials used are polyester, polypropylene, and nylon. A seat belt is not just the webbing; besides the webbing, it consists of other assembled components.
20
4
Share

Is the Land Cruiser domestically produced?

The Land Cruiser is available in both domestically produced and imported versions. The domestic version is manufactured by FAW Toyota, with its last model being the 2016 version, which includes four models, all meeting the China V emission standards. In terms of body dimensions, the Land Cruiser measures 5095mm in length, 1975mm in width, and 1930mm in height, with a wheelbase of 2850mm. Exterior-wise, the Land Cruiser adopts a family-oriented design, featuring very textured body lines and a visually appealing grille. Its large 5-meter-long body ensures excellent interior space. Under the hood, the Land Cruiser is equipped with a 4.0-liter V6 naturally aspirated engine, delivering a maximum power of 202 kW and a peak torque of 385 Nm.
2
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.