What are the solutions for the high fuel consumption of Wuling Hongguang?

What are the differences between the 2018 and 2019 Buick Verano?

The differences between the 2018 and 2019 Buick Verano: 1. Different exterior dimensions: The 2018 Verano measures 4718mm in length, 1802mm in width, and 1466mm in height; the 2019 Verano measures 4730mm in length, 1820mm in width, and 1488mm in height. 2. Different tire sizes: The 2018 Verano has tire specifications of 205/55R16; the 2019 Verano has tire specifications of 215/45R16. The Buick Verano comes standard with comprehensive active safety features such as six airbags, rear parking sensors, and tire pressure monitoring. It is also equipped with functions like ACC adaptive cruise control, FCA forward collision alert plus CMB collision mitigation system, LKA lane keeping system, SBZA side blind zone alert, and APA automatic parking assist.

7

3

Share

What is the wading depth of the Tiguan L?

The maximum wading depth of the Tiguan L is 580mm. The wading depth of the Tiguan L is determined by the height of the vehicle's chassis, which is the ground clearance listed in the model's parameter configuration. Generally, the greater the ground clearance, the higher the chassis, and the higher the safety factor when passing through waterlogged roads. Therefore, in terms of safe wading depth, the advantages of off-road vehicles and SUVs are obvious. However, for most compact and small vehicles with low chassis, the position of the vehicle's air intake should be used as a benchmark when passing through waterlogged roads. If the air intake of the Tiguan L is below the water level during wading, water will be sucked into the engine's cylinders. Since water cannot be compressed like air, it will cause severe damage to the engine's mechanical components (such as connecting rods, pistons, crankshafts, etc.). Therefore, the wading depth should not exceed the height of the engine's air intake. The height of the engine's air intake, and thus the maximum wading depth, can also be increased by installing a snorkel. If wading is unavoidable, the following safe and correct operations should be performed: Before the vehicle enters the water, always turn off the auto start-stop function to prevent the engine from automatically restarting after stalling in the water, which could cause severe damage due to water ingestion. Based on the passage of preceding vehicles, assess the underwater road conditions and choose an appropriate entry point. Observe the path taken by other vehicles and follow their tracks at low speed, avoiding sudden acceleration or deceleration. On roads prone to water accumulation, observe warning water level markers, trees, or reference points like the wheels and doors of other vehicles to estimate the water depth before deciding whether to proceed. Be aware of your vehicle's safe wading depth. If the water depth exceeds half the height of the tires or the engine's air intake, do not proceed and choose an alternative route instead.

2

5

Share

How much fuel does the Emgrand consume when the air conditioning is on?

When the air conditioning is on, the Emgrand consumes approximately 11 to 11.5 liters of fuel, with the air conditioning increasing fuel consumption by roughly 2 liters. Types of fuel consumption with car air conditioning: One occurs while driving. When the car speed is above 80 km/h, using the air conditioning is more fuel-efficient. Below 80 km/h, or when idling, the air conditioning relies solely on the engine, leading to more noticeable fuel consumption. Tips to reduce fuel consumption when using air conditioning: When the engine has just started and hasn't stabilized yet, turn on the external circulation for at least five minutes and open the windows to expel hot air from the car. Once the engine idle stabilizes, turn on the air conditioning—this saves fuel and avoids harming the engine; adjust the airflow direction. Since cold air sinks and hot air rises, point the vents upward to balance the temperature and cool the car more effectively; alternate between turning the air conditioning on and off. At speeds below 80 km/h, open the windows to reduce air conditioning fuel consumption. However, at speeds above 80 km/h, open windows increase wind resistance, consuming more fuel than using the air conditioning; turn off the air conditioning before shutting down the engine to prevent it from automatically turning on during the next start, which would increase engine load and fuel consumption.

2

3

Share

Reasons for the Malfunctioning Dashboard of Haval H6?

Haval H6 dashboard malfunction is caused by damaged dashboard lighting, short-circuited power supply wires, or blown power supply fuses. Dashboard repair methods: If the dashboard lighting is damaged, disassemble the dashboard. The lighting is usually located at the rear of the dashboard; replace the non-functioning lights. If the dashboard power supply wires are short-circuited, they must be replaced with new wires. If the dashboard power supply fuse is blown, simply replace it with a new fuse. Highlights of the Haval H6 model: The Haval H6 is positioned as an urban SUV, offering both two-wheel drive and four-wheel drive configurations. The H6 is built on a different platform compared to the previous H3 and H5 models. Its most notable feature is the use of a monocoque body. The four-wheel-drive version of the H6 employs an on-demand four-wheel-drive system. While this may somewhat affect off-road performance, it reduces body weight, improves fuel efficiency, and enhances ride comfort. As it is built on an entirely new platform, the two-wheel-drive version of the Haval H6 features front-wheel drive, which differs from the rear-wheel-drive setup of the H3 and H5 two-wheel-drive models.

19

2

Share

What are the solutions for CRV shaking when the air conditioner is turned on?

Here are the reasons and solutions for Honda CRV idle shaking: 1. Severe engine carbon deposits: The most common cause of car shaking is dirty throttle or excessive carbon deposits in the fuel injector. When there is too much carbon deposit inside the engine, the gasoline sprayed by the cold start injector will be largely absorbed by the carbon deposits, resulting in an overly lean mixture during cold starts, making it difficult to start. In this situation, the car can only start easily after the carbon deposits are saturated with gasoline. After starting, the gasoline adsorbed on the carbon deposits will be sucked into the cylinder by the engine's vacuum suction for combustion, making the mixture too rich. The engine's combustible mixture alternates between being too lean and too rich, causing idle shaking after a cold start. Additionally, the lower the temperature, the more fuel is needed for a cold start, and the presence of carbon deposits will affect the smoothness of the cold start. The solution is to clean the fuel system and check if the idle speed motor has carbon deposits that need cleaning. 2. Ignition system issues: Check the working condition of the spark plugs, high-voltage wires, and ignition coils. Poor performance of the ignition system or bad spark plug firing can also cause such faults. The solution is to check if the spark plugs have excessive carbon deposits and replace them if necessary. 3. Unstable oil pressure: If you have already cleaned the engine carbon deposits, cleaned the throttle, replaced the oil pad and spark plugs, but still notice body shaking at idle, it is recommended to go to a 4S shop to check the fuel supply pressure and the intake pressure sensor. If the fuel pump supply pressure is abnormal or the intake pressure sensor values are incorrect or malfunctioning, it can cause body shaking. The solution is to check the oil pressure and replace parts if necessary. 4. Aging engine components: Car shaking can also be related to aging engine mounts. Engine mounts are actually the shock absorption system of the engine. They absorb the slight vibrations of the engine during operation. If the engine mounts are faulty, these vibrations will be transmitted to the steering wheel and the interior of the car, causing shaking at idle. Carbon deposits can form in certain areas, especially the throttle. If the throttle is very dirty, it will obstruct the air intake, causing the engine to barely or insufficiently drive the compressor. This is why the car shakes when the air conditioner is turned on.

11

1

Share

What does it mean when the ABS light on the car is on?

When the ABS light is displayed on the car, it means there is a malfunction in the vehicle's Anti-lock Braking System. During emergency braking, if the wheels lock up, the vehicle may lose control and skid, making it difficult for the driver to slow down or adjust the vehicle's trajectory, posing significant safety risks. There are several states in which the ABS light may illuminate, each with different causes and solutions, as detailed below: State 1: ABS warning light remains constantly on (most common). Cause 1: The ABS speed sensor's sensing part is covered by dirt, mud, or other contaminants, affecting its ability to detect the corresponding speed signal. This prevents the ABS computer from determining the vehicle speed or the wheel's slip rate, thus failing to issue appropriate commands to adjust braking. Solution: Clean the dirt from the speed sensor and adjust the gap between the speed sensor and the signal ring to restore normal function. Cause 2: Poor signal transmission due to loose connections in the system wiring or poor contact in the ABS relay, leading to system failure. Solution: Check the wiring connections and reconnect any loose parts. State 2: ABS warning light intermittently illuminates but turns off during acceleration. Cause: When multiple vehicle electrical devices are in use, the battery voltage drops below 10.5V. As the engine speed increases, the voltage rises, causing the ABS light to turn off. This may also occur if the ABS system's power supply voltage is too low due to poor terminal contact or grounding issues. Solution: Check the battery's specific gravity; inspect the charging system; examine the power supply (e.g., voltage relay or poor power contact). State 3: ABS warning light remains on after engine start and only turns off when the engine is turned off (IGFF). Cause: Poor grounding contact in the ABS hydraulic valve body; loose wiring connections in the ABS hydraulic valve body; ABS computer malfunction. Solution: Loosen and then retighten the grounding screw on the hydraulic valve body, cleaning the contact surface if necessary; check if the connector gap has widened; replace the ABS or ABS/ASR computer. State 4: ABS warning light illuminates during high-speed driving. Cause: During high-speed driving, the ABS computer detects a significant discrepancy between the rear and front wheel speed signals; incorrect tire or wheel rim specifications. Solution: Refer to the vehicle's tire and wheel rim specifications, as indicated on the label near the fuel tank cap. State 5: ABS warning light intermittently illuminates. Cause: Improper adjustment of the brake light switch; poor internal contact in the brake light. Solution: Start the engine, press the brake pedal, push the brake switch linkage down fully with your fingers, then release the brake pedal to complete the self-setting position; replace the brake light switch if necessary.

3

4

Share

What are the solutions for the high fuel consumption of Wuling Hongguang?

What are the differences between the 2018 and 2019 Buick Verano?

What is the wading depth of the Tiguan L?

How much fuel does the Emgrand consume when the air conditioning is on?

Reasons for the Malfunctioning Dashboard of Haval H6?

What are the solutions for CRV shaking when the air conditioner is turned on?

What does it mean when the ABS light on the car is on?

What brand of tires does Tesla use?

Where is the daytime running light switch for the CS75?

How to Use the Cruise Control on the Regal?

What to Do If Paint Gets on the Car?