What are the small lights below the taillights of the Skoda Octavia?

2 Answers
McCharlotte
07/28/25 3:18pm
The two small lights below the taillights of the Skoda Octavia are the vehicle's position lights. The classification of taillight light sources is as follows: 1. Incandescent light source: An incandescent lamp is a thermal radiation light source that relies on electricity to heat the filament to incandescence to emit light, producing a continuous spectrum. 2. Light-emitting diode (LED): The principle of an LED is that in a forward-biased state, electrons from the N-region and holes from the P-region cross the P-N junction and recombine to emit light. 3. Neon light source: The principle of a neon light source is to apply an electric field at both ends of a discharge tube filled with inert gas to produce continuous discharge.
Was this review help?
5
0
Share
DiLondyn
08/11/25 10:51pm
I've been driving a Skoda Octavia for over ten years, and friends often ask me about the small light below the taillights. Actually, that's the reverse light, positioned near the bottom of the rear bumper, specifically designed to illuminate when you shift into reverse gear. It uses white light to brighten the area behind the car, which is especially useful when reversing at night or in underground parking lots, helping to prevent collisions with walls or obstacles. The light housing is waterproof, but over time the bulb may wear out. I personally check it every six months—replacing a new bulb doesn’t cost much. Safe driving shouldn’t overlook this small detail; if you notice it’s not working, fix it immediately—don’t delay. With European cars like the Octavia, the light placement is standardized, offering a wide illumination range—practical and reliable. Developing good driving habits is crucial, as it makes reversing much safer.
Was this review help?
3
3
Share
Expand All
More Forum Discussions

What Causes a Motorcycle to Stall Mid-Ride and Have Difficulty Restarting?

The reasons why a motorcycle stalls mid-ride and has difficulty restarting are: 1. Abnormal compression process: In many cases, a drop in compression pressure will cause stalling and difficulty starting. In such cases, measuring the compression pressure and checking valve clearance can help identify the general cause. The main reasons for decreased compression pressure include damaged cylinder gaskets, worn pistons, piston rings, or cylinders, poor sealing of the crankcase mating surfaces, improper valve seating, abnormal valve timing, or poor reed valve seating. The main reasons for excessive compression pressure include carbon buildup in the combustion chamber or on the piston top. 2. Fuel system abnormalities: If the motorcycle cannot obtain the proper air-fuel mixture, the engine will become difficult to start. The main reasons for no fuel or insufficient fuel supply include no fuel in the carburetor float chamber, a stuck needle valve, clogged fuel lines or filters, or a blocked fuel tank cap. 3. Ignition system issues: The engine may stall due to a weak or absent spark. The main causes of this phenomenon include insufficient current, incorrect ignition timing, or spark plug failure. Reasons for insufficient current include faulty electrical wiring, a malfunctioning main switch, engine kill switch failure, ignition coil failure, magneto failure, spark plug cap failure, or battery failure. The main causes of spark plug failure include incorrect heat range, worn electrodes, cracked ceramic insulation, damaged or broken gaskets, or carbon buildup.
10
4
Share

What is the difference between 48v20ah and 48v24ah?

Here are the differences between 48v20ah and 48v24ah: Different maximum output current: The maximum output current of 48V24AH is 24 amps; The maximum output current of 48V20AH is 20 amps. Different battery capacity: The 48V24AH has a larger battery capacity and can work for one hour at 24 amps; The 48V20AH can work for one hour at 20 amps. Different charging speed: The 48V24AH charges faster and takes less time to charge; The 48V20AH charges slower and takes longer to charge.
7
4
Share

How many points are deducted and how much is the fine for an illegal U-turn?

3 points will be deducted and a fine of 200 yuan will be imposed. The following is relevant information: 1. Relevant legal provisions: On road sections with no U-turn signs, making a U-turn will be penalized as violating prohibitory signs, prohibitions, or marking instructions, resulting in 3 points deducted and a fine of 200 yuan; According to Article 49 of the Road Traffic Safety Law: Motor vehicles are not allowed to make U-turns at locations with no U-turn or no left-turn signs or markings, as well as at railway crossings, pedestrian crossings, bridges, sharp curves, steep slopes, tunnels, or sections prone to danger; Motor vehicles can make U-turns at locations without no U-turn or no left-turn signs or markings, but must not obstruct the passage of other normally traveling vehicles and pedestrians. 2. Situations where U-turns are allowed: Intersections with U-turn signals; Intersections with U-turn signs; U-turns are allowed where there is no no U-turn sign or there is a separate U-turn indicator or left-turn signal. 3. Situations where U-turns are not allowed: Road sections with no U-turn signs; U-turns are not allowed on zebra crossings; Road sections where the center line is solid; Lanes with straight-only signs on the left cannot be used for U-turns; Intersections where left turns are prohibited.
10
1
Share

What is the shelf life of motorcycle engine oil?

Generally speaking, the sealed storage period of used engine oil varies depending on its type: motorcycle engine oil can be stored for up to 6 months without significant issues; semi-synthetic oil can be stored for 9 months; and full-synthetic oil can be stored for 12 months or even longer. Regardless of the type, this duration is sufficient to last until the motorcycle's next maintenance. Storage methods for opened engine oil: 1. Seal immediately after opening: After maintenance at the repair shop, the oil bottle cap should be tightened immediately. Note that since the original tin foil seal has been damaged, the remaining cap gasket provides limited isolation. At this point, you can use a clean plastic film to cover the bottle mouth. To prevent damage, it's best to fold it several times before covering, then screw on the cap for better sealing. If possible, you can also use wax to seal the bottle mouth. 2. Store in a dry and cool place: After sealing the oil bottle, it should be stored in a dry and cool place, ensuring it is not exposed to sunlight to prevent oxidation of the oil inside. 3. Do not pour completely: When using stored oil for the next maintenance, do not pour all of it into the engine. Retain a small portion, as there may be trace amounts of moisture at the bottom of the bottle after long-term storage, which could affect engine performance or even cause adverse effects if added to the engine.
10
2
Share

What does 4llc mean?

4llc stands for low-speed four-wheel drive with a central differential system, which is a measure of a vehicle's performance. Below is an introduction to vehicle drive and differential systems: Four-wheel drive: Also known as all-wheel drive, it means that both the front and rear wheels of the vehicle have power. The engine's output torque can be distributed in different proportions to all wheels based on the road conditions to improve the vehicle's driving capability. Central differential: A central differential is installed between the drive axles. In multi-axle drive vehicles, the drive axles are connected by drive shafts. To allow each drive axle to have different input angular speeds and eliminate wheel slippage, a central differential is used.
4
3
Share

The Function of Speed Limiting Cruise Control

The function of speed limiting cruise control is to achieve speed limitation by setting the maximum output throttle signal value through the controller. When the throttle output signal cannot exceed the set maximum value, the speed is restricted. The method to use speed limiting cruise control is to press the speed limiting cruise button and then pull down the RES button. Precautions for using speed limiting cruise control: 1. Do not use the speed control system on roads with heavy traffic or poor road conditions; 2. If the set cruising speed is too high compared to the current traffic conditions, do not immediately resume the set speed; 3. Do not shift the gear lever into neutral after the system is turned on.
7
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.