What are the simple methods to remove car stickers?

1 Answers
AngelinaLee
07/29/25 9:37pm
You can use essential balm, toothpaste, alcohol, or a hairdryer to easily remove car stickers. Here are the detailed instructions: Essential Balm: If there are some stickers with strong adhesion that are difficult to peel off, you can buy a bottle of essential balm from a pharmacy. Then, take a towel or tissue, drip some essential balm on it, and slowly wipe the sticker. This will make it easy to remove without damaging the car's windshield. Toothpaste: If there is a transparent film on the windshield, you can use a little toothpaste. Slowly and repeatedly rub the area with the sticker for a while, then use an oil card to gently scrape off the residual adhesive. Remember not to use a blade or any sharp object to scrape, as it may scratch the windshield. Alcohol: Take a towel, pour some alcohol on it, and wipe a few times. It's simple and practical. However, be careful not to spray alcohol directly on the windshield, as it may damage the car film. Hairdryer: If the transparent film has been on for too long and has aged, making it difficult to peel off, you can use a hairdryer to heat it up. This will make it easier to remove. Do not hold the hairdryer too close if the temperature is too high; about one minute should be sufficient.
Was this review help?
3
1
Share
More Forum Discussions

How to Use Cruise Control Function?

Cruise control usage is divided into five steps. Below is an introduction to cruise control usage: 1. Press the power button to activate the system, at which point the cruise control indicator light on the dashboard will illuminate. 2. Accelerate to over 40km/h, then press the SET button. At this point, release the accelerator with your right foot, and the speed will be set at the current velocity. 3. Press the RES (+) button to increase speed from the current setting, or press the SET (-) button to decrease speed from the current setting. 4. There are three ways to deactivate cruise control: stepping on the brake, pressing the CANCEL button, or pressing the power button. 5. If cruise control is canceled by stepping on the brake or pressing the cancel button, you can press the RES button to resume the previously set cruise control speed.
3
1
Share

What is the top speed of the 2012 Skoda Fabia?

The top speed of the 2012 Skoda Fabia is 175km/h. Below is an introduction related to top speed: Factors affecting top speed: There are many factors that affect a car's top speed, such as the power of the car's engine, the engine's maximum torque, the speed at maximum torque, the transmission ratio of the drivetrain, and driving resistance. The resistance mainly refers to air resistance and rolling resistance. Top speed of common car models: The top speed of general small cars is about 180km/h, mid-to-high-end cars can reach 250km/h, and imported sports cars can have a maximum speed of 280km-300km/h.
9
3
Share

What are the causes of glass breakage?

Glass is formed by melting silicon dioxide and other chemical substances together (the main production raw materials are: soda ash, limestone, quartz). There are 4 main reasons that cause glass breakage: 1. Glass damage leading to breakage: Scratches, surface corrosion, or chipped edges on the glass surface or edges due to careless handling, installation, or maintenance can easily disrupt the stress balance of the glass, triggering spontaneous breakage of tempered glass. 2. Breakage during installation: During the installation process, if the installation gap is too small or the glass directly contacts the frame, the different expansion coefficients of glass and frame under sunlight can generate compressive forces on the edges or corners of the glass, inducing breakage. 3. Breakage caused by glass processing: Glass with drilled holes or cut corners is prone to breakage. 4. Natural environmental factors causing glass breakage: Wind disasters such as strong typhoons can lead to the failure of wind pressure resistance design, resulting in glass breakage.
20
4
Share

How to Refurbish Car Headlights?

Car headlights can be refurbished through polishing, which is the most commonly used method in car detailing shops. This repair method is fast, convenient, and effective for refurbishment, with low costs. Since the headlight surface is generally made of plastic rather than paint, the light transmittance decreases when the wax component on the surface wears off. The specific steps are as follows: 1. Clean the dust and dirt on the headlight surface. 2. Use tape to cover and protect the areas around the headlight that do not require refurbishment. 3. Sand the surface with water sandpaper. 4. After sanding, remove the powder, then use a towel dipped in polishing wax to polish in a circular motion.
6
5
Share

How to Remove the ETC Device?

ETC device removal depends on blocking the anti-tamper switch. You can press the electronic tag firmly with your hand, then use a wallpaper knife to cut through the double-sided adhesive between the device and the windshield. Be sure to keep pressing the anti-tamper switch during the entire process and remove it carefully. Here are some important notes about ETC lanes: 1. Do not exceed the speed limit when passing through an ETC lane. The ETC lane sensing area is 8 meters, and the sensing speed is below 20km/h. Speeding may not only prevent the system from detecting your vehicle but could also result in penalty points. 2. If a driver mistakenly enters an ETC lane, making a U-turn is not considered a traffic violation. If there are no vehicles behind, you can reverse and enter an MTC lane or a manual toll lane to pay the toll in cash or by card. If there are vehicles behind, you can ask them to make way or seek assistance from toll station staff.
7
0
Share

What maintenance is needed for a sedan at 10,000 kilometers?

The 10,000-kilometer maintenance is mostly the second maintenance for a car, also known as the second service. The specific maintenance items for a sedan at 10,000 kilometers are as follows: 1. Replace the engine oil and oil filter: The engine oil needs to be replaced at 10,000 kilometers. Since the oil plays a lubricating role during the operation of the car, as the vehicle usage time extends, the performance of the engine oil may degrade or even fail, so it needs to be replaced in time during vehicle maintenance. 2. Vehicle inspection: After driving 10,000 kilometers, the car's engine, transmission, air conditioning system, steering system, braking system, suspension, body, tires, etc., need to be inspected to ensure the performance of the car during operation. 3. Clean or replace the air and cabin air filters: After driving 10,000 kilometers, it is recommended that the owner clean the air and cabin air filters. 4. Check various vehicle fluids: After driving 10,000 kilometers, it is necessary to check the coolant, brake fluid, tire pressure, etc. During the operation of the car, if there are abnormalities in the various fluids, abnormal wear may occur during the operation of the car, affecting its performance.
11
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.