···
Log in / Register

What are the safe driving tips for rainy days?

4 Answers
ONevaeh
09/03/25 7:29am

Safe driving tips for rainy days: Maintain good visibility, drive slowly and cautiously, stay away from large vehicles, and pay attention to pedestrians. Rainy weather can easily lead to traffic accidents due to obstructed driver visibility, so maintaining good visibility is crucial. Turn on the windshield wipers to clear raindrops promptly; when the weather is dim, turn on the low beams, fog lights, and marker lights; if there is fog on the windshield obstructing visibility, turn on the air conditioning to disperse the fog; keep the rearview mirrors clear by activating the heating function or adding plastic shields to block the rain; observe the surrounding road conditions carefully and drive cautiously. Drive slowly and cautiously: Reduce speed and maintain a safe distance; drive carefully, always paying attention to road conditions, especially in areas with many pedestrians; adjust speed according to road conditions, and control speed more strictly on unfamiliar roads; follow the car ahead, and drive carefully along the path of the preceding vehicle on unfamiliar or difficult road sections; follow slowly, avoid speeding blindly, and ensure safety before overtaking. Stay away from large vehicles: Keep a greater distance from large vehicles; do not let large vehicles block your view ahead; be aware of the blind spots of large vehicles to avoid danger; stay away from large vehicles to prevent splashed rainwater from interfering with driving; do not follow blindly—large vehicles may pass through waterlogged sections that small vehicles might not navigate successfully. Pay attention to pedestrians: Do not compete with pedestrians for the right of way, and yield appropriately; observe pedestrian movements to avoid startling them and causing them to slip; if it is inconvenient to avoid, stop and wait; be mindful of waterlogged areas, pass through slowly, and avoid splashing water onto pedestrians.

Was this review help?
11
0
Share
Haven
09/16/25 2:05am

On rainy days with slippery roads, I always drive with extra caution. The top priority is to slow down, as braking distances are longer on wet surfaces compared to dry ones, so I reduce my speed by at least 20 km/h. Maintaining a safe following distance is crucial—I make sure to leave twice the usual space between my car and the one ahead. Sudden braking on wet roads can easily cause skidding, so I apply the brakes gently for better safety. Turning on the headlights and taillights is a must to increase visibility to other drivers, while avoiding hard acceleration and sharp steering. Puddles can lead to hydroplaning, so I steer clear of deep water whenever possible. If I have to drive through standing water, I keep the steering wheel steady. If the rain becomes too heavy, I pull over, turn on the hazard lights, and wait for it to ease up. Regularly checking tire tread depth is important—worn-out tires with poor drainage can lead to loss of control. Additionally, I use the air conditioner to defog the windows for clear visibility. Safe driving in the rain is no small matter—being cautious is always the right approach.

Was this review help?
16
1
Share
Expand All
Alina
10/30/25 2:41am

Before every rainy season, I always inspect my vehicle. Tires are a key focus—adequate tread depth ensures effective water drainage to prevent skidding; if they're worn out, replace them immediately. Wiper blades that have aged can obscure visibility, so check for cracks or signs of drying and replace them if needed. All lighting systems must be functional: adjust the headlight angles when turned on to avoid glare, and ensure taillights are clearly visible. Windows tend to fog up in the rain, so I activate the air conditioning's defogging feature to keep the interior dry. Brakes must be checked for responsiveness; wet roads demand quicker reaction times, making preemptive maintenance essential. If heavy rain is encountered while driving, keep the speed under 60 km/h. I also make it a habit to check weather alerts before setting off—if a storm is forecast, consider delaying the trip or using alternative transportation. Safety comes first, as overlooking small details can lead to major accidents.

Was this review help?
20
1
Share
Expand All
SanJordan
12/13/25 2:48am

Driving in the rain is most challenging due to blurred vision, so I always turn on the headlights to enhance visibility. Adjust the wiper speed to an appropriate level to promptly clear rainwater and maintain clear sight. Reduce your speed by 10-15 km/h compared to normal conditions for safety, and increase the following distance to prevent rear-end collisions. Keep a firm grip on the steering wheel and avoid sudden turns, as wet roads increase the risk of skidding. Regularly wipe the inside of the windshield to prevent fogging, which can worsen visibility when combined with rain. Turn on fog lights for additional illumination in poor lighting conditions. Stay focused on the road and minimize lane changes to avoid distractions and accidents. If heavy rain severely impairs visibility, pull over and wait for conditions to improve. Regular maintenance of wipers and tires ensures they remain in good condition. Following these steps makes driving in the rain safer and more reassuring.

Was this review help?
4
1
Share
Expand All
More Forum Discussions

How many points will be deducted for parking within 10 meters of an intersection?

Parking within 10 meters of an intersection will result in a deduction of 3 points and a corresponding fine. Below are the relevant regulations: In sections of the road with no-parking signs or markings, in sections where there are separation facilities between motor vehicle lanes and non-motor vehicle lanes or sidewalks, as well as in crosswalks and construction zones, motor vehicles are not allowed to park on the road. At intersections, railway crossings, sharp curves, narrow roads less than 4 meters wide, bridges, steep slopes, tunnels, and within 50 meters of these locations, motor vehicles are not allowed to park on the road. In front of bus stops, emergency stations, gas stations, fire hydrants, or fire stations, and within 30 meters of these locations, motor vehicles are not allowed to park on the road. When parking on the roadside, vehicles should be parked close to the right side of the road. The driver must not leave the vehicle and should drive away immediately after passengers get on or off or after loading or unloading goods.
3
4
Share

What are the steps for installing a car anti-theft device?

The steps for installing a car anti-theft device are: 1. Remove the cover under the steering wheel and pull out the two brown turn signal wires from the main harness; 2. Take out the original car plug and connect it to the anti-theft device plug, straighten the wires after connecting, then replace the cover and tighten the screws; 3. Connect the door wire, the turn signal wire and the door wire are together, wrap them with tape after connecting and plug the connector back; 4. Connect the iron wire, brake pedal wire, and horn wire; 5. Install the central lock and anti-theft horn. A car anti-theft device is an alarm system installed in a vehicle. If someone hits, impacts, or moves the car, the sensor will send a signal to the controller indicating the vibration intensity. Depending on the intensity of the vibration, the controller will emit a warning sound or trigger a full alarm to deter thieves and alert the owner.
13
3
Share

What transmission does the Nissan Tiida use?

Nissan Tiida uses a 5-speed manual and CVT transmission. The functions of the transmission are: 1. Change the transmission ratio; 2. Expand the torque and speed of the driving wheels; 3. Enable the car to drive in reverse; 4. Facilitate gear shifting or power output of the transmission. Taking the 2021 Nissan Tiida as an example, it is a compact car with body dimensions of: length 4393mm, width 1766mm, height 1539mm, wheelbase of 2700mm, and a body weight of 1180kg. The 2021 Nissan Tiida is equipped with a 1.6L inline 4-cylinder naturally aspirated engine, with a maximum horsepower of 184PS, maximum torque of 155Nm, maximum power of 90kW, and is paired with a 5-speed manual transmission.
8
4
Share

What Causes the Brake Pedal to Be Hard to Press After Starting the Car?

Car starting after the brake pedal is hard to press reasons are: 1. The car's vacuum booster pump leaks or fails; 2. The brake was pressed again after the engine was turned off, related to the brake booster pump; 3. Lack of necessary maintenance on the brake system, too much debris in the brake master cylinder, poor sealing, or vacuum booster pump failure; 4. Improper operation leading to mechanical failure. Solutions for the brake pedal being hard to press after starting the car: 1. Restart the engine and try to press the brake pedal hard again; 2. While driving, the priority is to slow down and stop, try pressing the pedal multiple times to restore braking; 3. If this situation is discovered before driving, the car can be directly sent to a repair shop.
2
5
Share

What are the symptoms of a faulty clutch disc?

The symptoms of a faulty clutch disc include: 1. The clutch engagement point becomes higher - when starting the vehicle, you originally needed to release the clutch pedal by 1cm to move, but now it requires lifting to 2cm; 2. Noticeable decrease in vehicle power - with no engine abnormalities, whether starting or climbing hills, the car feels sluggish with insufficient power despite high engine RPM, indicating clutch slippage; 3. Metallic grinding noises when depressing or releasing the clutch pedal, which likely results from severe clutch disc wear; 4. Uneven engagement when releasing the clutch during startup, causing jerky front-back movements, along with rough/stiff operation when pressing or releasing the clutch pedal - these indicate the need for clutch disc replacement.
20
4
Share

What is the usage method of piston ring pliers?

The usage method of piston ring pliers is: Clamp the opening of the piston ring with the ring clip on the piston ring pliers, hold the handle and apply even force gently, making the pliers' handles slowly contract while the ring clip gradually expands the piston ring, allowing it to be removed from or installed into the piston ring groove. When using piston ring pliers to install or remove piston rings, the force must be applied evenly to avoid breaking or damaging the piston ring due to excessive force, and also to prevent hand injuries. The piston ring removal method: 1. Remove a piston and wipe it clean with a cloth; 2. Use piston ring pliers to remove the two compression rings; 3. Remove the first compression ring first, then the second; 4. Pay attention to the direction of the rings during removal; 5. Remove the oil ring; 6. Arrange the oil rings in order; 7. Use needle-nose pliers to remove the piston pin circlip; 8. Use a special tool to remove the piston pin; 9. After removal, use a scraper to clean carbon deposits from the piston.
10
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.