···
Log in / Register

What are the rules for returning a borrowed car?

1 Answers
SanKatherine
07/29/25 3:30pm

There are 6 rules to follow when borrowing someone else's car: Drive gently: Don't rush at traffic lights, avoid squeezing in traffic jams, and try to steer clear of muddy roads, waterlogged areas, or bumpy sections - if unavoidable, proceed with caution. Don't move items inside the car: Many car owners keep daily necessities or snacks in their vehicles for emergencies. It's advised not to relocate or use these items without the owner's permission. Provide updates during prolonged use: If borrowing for an extended period, remember to update the owner about the car's condition. Report any accidents honestly and cover repairs: In case of minor scratches or collisions, inform the owner proactively and bear repair costs - never conceal damages. Do a walk-around inspection before returning. Refuel and clean before returning: Remember to refill the tank and clean the car thoroughly before returning. Take responsibility: After returning, note the license plate number and check traffic violation records for 1-2 months to confirm no unintentional penalties occurred.

Was this review help?
11
3
Share
More Forum Discussions

What Causes Low Idle Speed in a Car?

Low idle speed in a car may be caused by low battery voltage; carbon deposits; the control unit receiving incorrect signals and issuing wrong commands, leading to inaccurate control of engine idle air intake and abnormal combustion. It can also result from faulty idle air actuators causing inaccurate idle air control. The impact of idle speed on gasoline engines is as follows: 1. Fuel Economy: Since engines often operate at idle, statistics show that about 30% of urban vehicle fuel consumption occurs during idle. Therefore, reducing fuel consumption during idle is crucial, which is also a requirement for idle control. 2. Emissions: During idle, gasoline engines have a high amount of residual exhaust gas in the cylinders. To ensure stable combustion, the mixture needs to be enriched, leading to incomplete combustion and the production of harmful emissions like CO and HC. Experiments prove that lower idle speeds increase the dilution effect of exhaust gases, further raising CO and HC emissions. Thus, increasing idle speed helps reduce CO and HC emissions. Relevant data and experiments show that increasing engine idle speed from 700r/min to 800r/min reduces CO by 10% and HC emissions by 15%.
5
3
Share

How often should the motor vehicle inspection compliance label be replaced?

For new small passenger vehicles, inspection is required every two years for the first 6 years, and every six months after reaching 15 years. Each inspection results in the issuance of a new compliance label, which displays the valid date. The specific inspection schedule is as follows: 1. Operational passenger vehicles must be inspected annually within the first 5 years, and every 6 months thereafter; 2. Trucks and large/medium non-operational passenger vehicles must be inspected annually within the first 10 years, and every 6 months thereafter; 3. Small and mini non-operational passenger vehicles must be inspected every two years within the first 6 years, annually thereafter, and every 6 months after reaching 15 years; 4. Motorcycles must be inspected every two years within the first 4 years, and annually thereafter; 5. Other motor vehicles must be inspected annually. Required documents for the procedure: 1. Motor vehicle registration certificate; 2. Compulsory traffic accident liability insurance certificate; 3. Motor vehicle safety technical inspection compliance certificate.
4
5
Share

What does brake system failure mean?

Brake system failure means that there is a malfunction in the braking system. The causes of brake system failure in a car include: 1. Insufficient brake fluid. 2. Air in the brake system. 3. Excessive free travel of the brake pedal or excessive clearance in the brake, poor contact of the brake shoe friction lining, severe wear, or oil contamination. 4. Blockage in the brake system pipelines. The possible reasons for brake system failure in a vehicle are as follows: 1. Excessive wear of the brake pads: Some brake pads come with a sensor wire that activates a circuit when the wear reaches the limit, causing the warning light on the dashboard to illuminate. 2. Insufficient brake fluid: A lack of brake fluid is often accompanied by significantly reduced braking force, and in severe cases, a complete loss of braking power. This issue can be resolved by promptly replenishing the brake fluid.
9
1
Share

Do I need to replace all 4 glow plugs if one is broken?

Do I need to replace all 4 glow plugs if one is broken? The following is the relevant introduction of glow plugs: 1. The function of glow plugs: Glow plugs are used to preheat the intake air when the diesel engine is started at low temperature. Using glow plugs in winter can shorten the starting time, reduce the current consumption of the battery and reduce the wear of the diesel engine. 2. Cold engine power-on: When the engine is cold, power the glow plugs for 2 minutes, and touch the electrode of each glow plug with your hand. If the heating element of the glow plug is disconnected, the electrode will be cold. This method is simple and easy to implement, but the effect is slightly worse. 3. Single test: Test each glow plug individually, remove each glow plug, ground the outside of the glow plug, connect the live wire to the glow plug terminal F (use 12V power for vehicles with 24V batteries), and conduct a short-cycle test. If the glow plug becomes hot, it means it is intact.
15
1
Share

What is the highway fuel consumption of the BMW 325?

The BMW 325 has a highway fuel consumption of 8.3 liters per 100 kilometers. Fuel consumption is not only related to the car itself but also depends on the driver's habits and road conditions. Here is additional information about the BMW 325: 1. The BMW 325 is equipped with a medium-power 2.0-liter turbocharged engine, which has a maximum power output of 135 kW and a maximum torque of 300 Nm. The engine reaches its maximum power at 5,000 to 6,000 rpm and its maximum torque at 1,350 to 4,000 rpm. This engine features direct fuel injection technology and uses an aluminum alloy cylinder head and block. It is paired with an 8-speed automatic transmission (8AT). 2. The BMW 3 Series also includes models with a high-power 2.0-liter turbocharged engine, which delivers 258 horsepower and a maximum torque of 400 Nm. This engine is also matched with an 8AT transmission from ZF. The new BMW 3 Series features a double-joint independent front suspension and a multi-link independent rear suspension.
12
4
Share

What are the reasons for the Lavida's heater not producing hot air?

The following are the reasons why the Lavida's heater may not produce hot air: 1. The thermostat is constantly open or opens too early: The cooling system prematurely enters the large circulation cycle, and with the low external temperature, especially when the car is moving, the cold air quickly cools the antifreeze, preventing the engine water temperature from rising and the heater from producing hot air. 2. The water pump impeller is damaged or slipping: The flow rate through the heater's small radiator is insufficient, preventing the heat from rising. 3. There is airlock in the engine cooling system: Airlock causes poor circulation in the cooling system, resulting in high water temperature and the heater not producing hot air. If there is always air in the cooling system, it is likely caused by a damaged cylinder gasket allowing air into the cooling system. If the inlet pipe of the heater's small radiator is very hot while the outlet pipe is relatively cool, this situation indicates a blockage in the heater's small radiator, which should be replaced.
8
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.